Cybex 445T Treadmill Owner’s Manual
ITEM | QTY. PART NO. | DESCRIPTION | |
NO. |
|
|
|
76 | 2 | Bolt, 3/8 x 2.25, HXHD CAP, Black Zinc, G5 | |
77 | 2 | Nut, Jam 3/8 - 16, Black Zinc | |
78 | 1 | Weldment, Motor Base | |
80 | 2 | Bearing, | |
81 | 1 | PCA, Control Board, 115 VAC, 445T | |
81 | 1 | PCA, Control Board, 230 VAC, 445T | |
82 | 1 | Switch, Rocker, Thermal CB, 15 A | |
82 | 1 | Switch, Rocker, Thermal CB, 20 A | |
83 | 1 | Filter, 16 Amp | |
83 | 1 | Filter, 20 Amp | |
84 | 4 | KEPS, 5/16 - 18, HEX STL ZINC | |
85 | 8 | Screw, SEMS, 8/32 x .38, PNHD EXT Black Zinc | |
86 | 8 | Wire Tie, Nylon, 9 | |
87 | 2 | KEPS, | |
88 | 1 | Washer, Lock External, No. 10 ZC | |
89 | 2 | Screw, SEMS, | |
90 | 1 | Wire Tie, Nylon, 18 | |
91 | 1 | Plate, Circuit Breaker Mount | |
92 | 1 | Label, Disconnect Power, Multilingual | |
93 | 1 | Decal, Warning, Motor Plate | |
94 | 1 | Decal, IS3 logo | |
95 | 1 | Bracket, Idler | |
96 | 1 | Idler Wheel, 1.88 x 1.0 | |
97 | 2 | Bushing, Flange, .375 x .469 x .25 | |
98 | 1 | Screw, 3/8 - 16 x 1.75, SCHD BTN, BLK, ZN | |
99 | 1 | Decal, IR Comp Adjust, English | |
100 | 1 | Plug, Plastec, 7/16”, Black | |
101 | 1 | Bracket, Power Factor, Choke | |
102 | 1 | Motor, Elevation, 115 VAC | |
102 | 1 | Motor, Elevation, 230 VAC | |
103 | 1 | Motor, Drive, 110 VAC | |
103 | 1 | Motor, Drive, 220 VAC | |
111 | 1 | Weldment, Monitor Bracket, 445T | |
120 | 1 | Heat Sink, Silpad | |
121 | 1 | Ferrite, | |
122 | 1 | Choke | |
123 | 2 | Strip, Motor Base, Isolation | |
124 | 1 | Bushing, Strain Relief, .370” | |
200 | 1 | Assembly, Top Platform, Right | |
201 | 1 | Assembly, Top Platform, Left | |
202 | 1 | Weldment, Upright | |
203 | 1 | Weldment, Frame, 445T | |
204 | 2 | Decal, Safety Walk | |
205 | 8 | Screw, | |
206 | 1 | Cover, Rear, Top Left | |
207 | 1 | Cover, Rear, Bottom Left | |
208 | 1 | Cover, Rear, Top Right | |
209 | 1 | Cover, Rear, Bottom Right | |
210 | 1 | Decal, “CX 445T”, Black | |
210 | 1 | Decal, “CX 445T”, Silver 877 | |
211 | 1 | Plug, Hole, Plastic, 1”, Black | |
220 | 1 | Shaft, Deck Pivot, 445T | |
221 | 2 | Weldment, Deck Pivoting Bracket | |
222 | 1 | Bearing, IGUS | |
300 | 1 | Assembly, 445T Console, English | |
301 | 1 | Assembly, Cover, Top CHR, English | |
304 | 1 | PCA, Display, 445T | |
305 | 1 | Bracket, Console Anchor, Right | |
306 | 1 | Bracket, Console Anchor, Left | |
308 | 1 | Decal, Warning, Right | |
309 | 1 | Decal, Warning, Left | |
310 | 1 | Sensor, Polar Wireless Remote Mount | |
311 | 4 | Screw, | |
312 | 7 | Screw, SLFTP, | |
313 | 1 | Tape, Double Sided, .032 Thick | |
314 | 2 | Tab, Book Holder | |
|
|
|
|
Customer
Service
Page
