Cybex 710T Treadmill Owner’s Manual

If the drive motor (and running belt) does not rotate at all, the problem is more difficult to diagnose. First, suspect the power relay and check it by going into diagnostics, C18, and press the v elevation button in conjunction with the SPEED + button. This will toggle the relay on/off. You should be able to hear the relay toggle and note as well that the value in the center window reads “1.” If it reads zero, the problem is most likely the console cable.

If none of these prove to be the problem, have a qualified service technician check the wiring for wear or abrasion and also inspect the motor brushes. Any arcing, pitting or burning of the brushes, or a brush that is less than .438” (7/16"/11.13mm) indicates the need for brush replacement. The tightness of the brush cap and brush holder mount in the drive motor housing should also be checked. NOTE: There are two lower board fuses which allow power to the display and to the motor drives. The upper display is not likely to light up at all if one or both of the fuses need to be replaced. Have a qualified service technician replace these only with equivalent value fuses.

ERROR 2: EXCESSIVE CURRENT DRAW

This error code is generated by exceeding the current limit of the motor drive system for two seconds. The error is generated to help prolong the life of the treadmill and alert the owner to a potentially damaging situation. Most common occurrences of this are high belt/deck friction due to wear or contamination, a worn motor, or a breakdown of the choke. Problems in the drive motor brush area, such as worn, pitted or arcing motor brushes, a loose drive motor brush cap, or a loose drive motor brush holder can also cause this error code to

be generated.

Another source of this problem could be excessive friction between the deck and belt, usually caused by a lack of routine belt/deck cleaning (see Chapter 5), or by a worn deck.

A third cause for this code could be a defective choke or a poor connection at the choke assembly.

Last, the failure of an electronic component in the motor control or loss of magnetism in the drive motor permanent magnet could also generate this error code.

ERROR 3: LOSS OF SPEED SIGNAL

This error code occurs after the treadmill has successfully started and indicates that the com- puter in the display control panel has lost the motor speed signal from the speed sensor. The causes for this error are similar to those listed for Error 1.

ERROR 50: OVERSPEED

This error code indicates a problem with the speed control circuitry. This error is stored as ERROR 6 but displayed as ERROR 50.

It can occur if the treadmill recognizes a discrepancy in the actual belt speed vs. the speed set at the control panel. If the actual speed of the belt is 1 mph (1.6 kph) over the set speed for 0.2 seconds or 2 mph (3.2 kph) below the set speed for 2 seconds, this error code will be displayed.

Page 7-12

Page 74 Page 76
Page 75
Image 75
Cybex International 710T manual Error 2 Excessive Current Draw, Error 3 Loss of Speed Signal, Error 50 Overspeed
Page 74 Page 76

LT-14464-4 Rev H, 710T specifications

The Cybex International 710T, LT-14464-4 Rev H is a top-tier piece of fitness equipment designed for commercial gym settings and serious home workout enthusiasts. This high-performance treadmill stands out due to its innovative features, robust design, and technology that prioritizes user comfort and efficiency.

One of the central features of the 710T is its advanced mechanics, which include a powerful DC motor that provides a smooth and consistent performance across various speeds. With a top speed of 12 miles per hour and an incline of up to 15%, users can engage in a diverse range of workouts that simulate outdoor running and walking environments. This versatility makes the 710T suitable for users of different fitness levels, from beginners to seasoned athletes.

The treadmill also boasts a spacious running surface of 22 inches by 60 inches, allowing for comfortable strides and reduced risk of injury. The patented FlexTech® system is engineered to absorb impact, providing a cushioned deck that minimizes stress on joints while still allowing for an effective workout. This technology promotes longer exercise sessions, which can contribute to better overall fitness goals.

Another remarkable feature is the intuitive console equipped with a large, easy-to-read display that offers users essential metrics, including time, distance, calories burned, and heart rate. The console is designed for simplicity and ease of use, with quick-access buttons for speed and incline adjustments, enabling users to customize their workouts effortlessly.

Connectivity is a significant aspect of modern workout experiences, and the 710T does not disappoint. It includes built-in Bluetooth compatibility, allowing users to sync their devices with fitness apps for tracking and sharing workout progress. Additionally, the integrated USB charging port ensures devices remain powered during exercise, allowing for uninterrupted music or entertainment.

Safety is a top priority, and the Cybex 710T is equipped with emergency stop features and adjustable handrails for added stability. The durable construction of the treadmill makes it suitable for heavy daily use, ensuring longevity and reliability.

In summary, the Cybex International 710T, LT-14464-4 Rev H is a comprehensive treadmill engineered with innovative technology, robust design, and user-friendly features that cater to various fitness needs. Its combination of performance, safety, and connectivity epitomizes the philosophy of Cybex in promoting an efficient and enjoyable workout experience.
Top Page Image Contents