Factory Defaults | Lantronix 10 instruction

Configure

3.8.3 Disable Telnet Setup

This setting defaults to the N (No) option. The Y (Yes) option disables access to this Configuration Menu by Telnet (port 9999). It only allows access via the Web pages and the serial port of the unit.

3.8.4 Disable TFTP Firmware Upgrade

This setting defaults to the N (No) option. The Y (Yes) option disables the use of TFTP to perform network firmware upgrades. With this option, firmware upgrades can be performed only by using a *.hex file over the serial port of the unit.

3.8.5 Disable Port 77FE (Hex)

Port 77FE is a setting that allows DeviceInstaller, Web Pages, and custom programs to configure the unit remotely. You may wish to disable this capability for security purposes. For more information about remote configuration, see the Lantronix Embedded Integration Kit user guide on the Lantronix Web site www.lantronix.com.

The default setting is the N (No) option, which enables remote configuration. You can configure the unit by using DeviceInstaller, Web pages, Telnet, or serial configuration. The Y (Yes) option disables remote configuration and Web pages.

Note: The Yes option disables many of the GUI tools for configuring the Device Server, including the embedded Web Page Configuration tool.

3.8.6 Disable Web Server

This setting defaults to the N (option). The Y (Yes) option disables the use of the Web Page Configuration tool that is built into the unit.

3.8.7 Enable Enhanced Password

This setting defaults to the N (option), which allows you to set a 4-character password that protects the Configuration Menu via Telnet and Web pages. The Y (Yes) option allows you to set an extended security password of 16-characters for protecting Telnet access.

3.9 Factory Defaults

Select 7 to reset the unit’s Channel 1 and Enhanced Security to the factory default settings. The server configurations (IP address information) remain unchanged.

3-26	UDS-10 User Guide

Image 66

Lantronix 10 manual Factory Defaults

Contents

UDS-10 User Guide Copyright and Trademark Disclaimer and Revisions Date Rev Author Comments Declaration of Conformity Warranty Sales Offices Table of Contents Server Configuration Network Configuration DeviceComm Manager 10.1 List of Figures UDS-10-IAP List of Tables Disconnect Mode Options Page Introduction UDS-10 UDS-10B UDS-10-IAP Device Server UDS-10-IAP Industrial Automation Protocols IP Address Network ProtocolsPacking Algorithm Port Number Serial Interface RJ-45 Ethernet Interface DIR PIN Signal NameEthernet Cable Primary Function Serial Interface Connection LEDs LEDMeaning Dimensions Product Information LabelSoftware Support Power Requirements Reset Switch Technical Specifications Technical SpecsPage Ethernet MAC Address Getting StartedAddresses and Port Number Internet Protocol IP Address Physically Connecting the Unit UDS-10 Connected to Serial Device and Network Methods of Assigning the IP Address Method Description Dhcp AutoIP DeviceInstaller Install DeviceInstaller Software DeviceInstaller Window Assign IP Address and Network Class Test the IP Address Ping Device Window Add the Unit to the Manage List Search Network Window Devices in a Group Opening a Configuration Window Device Management Window ARP and Telnet Serial Port Login Configuring the Unit Configuring via Web Browser Using DeviceInstaller Configure Web Manager Web Manager 3.0 has the following buttons Unit Configuration Telnet Password Server Properties Port Properties Configure Update Settings Technical Support Configuring via the Setup Mode Window Using a Telnet Connection Setup Mode Window Server Configuration Network Configuration Using the Serial PortSet Gateway IP Address Netmask Number of Bits for Host Part Network Class Host Bits NetmaskNetmask Host Bits Change Telnet configuration password Dhcp Naming Mode Option Channel 1 Configuration Serial Port Parameters2 I/F Interface Mode Baudrate Common I/F Mode Setting Binary Hex Flow Flow Control Option HexPort Numbers Reserved for Connect Mode Connect Mode Option Manual Connection Address Example Modem Mode Function Command ATD Remote Port Disconnect Mode OptionRemote IP Address DisConnMode Flush Mode Buffer Flushing Input Buffer Serial to Network Pack Control Pack Control Options Send Characters DisConnTime Inactivity TimeoutChannel Port Password Telnet Terminal Type Disable Snmp Expert SettingsSecurity Settings TCP Keepalive time in s Factory Defaults Exit Configuration Mode Get Configuration Set Configuration Updating Protocol Firmware Protocol Firmware Via DeviceInstaller Search Network Window Upgrade Firmware Via Tftp Via Another Unit Tftp Dialog Box Via the Serial Port DeviceComm Manager Installing DeviceComm Manager Install DeviceComm Manager Setup Status Meaning Firmware Troubleshooting Technical Support Troubleshooting Problems and Error Messages Firmware field UDS/CoBox Page Entering Monitor Mode Via the Serial Port Monitor ModeMonitor Mode Entering Monitor Mode Via the Network Port Command Command Name Function Response Meaning Network Configuration using UDP Byte Command ParametersUDP Datagrams Byte Command Parameters Configuring Multiple Devices Acquiring a Valid Setup Record Sending a Setup Record Intel Hex Format Option Hex Calculating the Checksum Calculating the Two’s Complement Setup Records Bytes Function Channel Parameters Channel Parameters Interface Mode Option Binary Hex Baud Rate Flow ControlSpeed Hex Bps Connect Mode Disconnect Mode Function 5 4 3 2 1 Option Subnet Portion IP AddressesNetwork Portion Network Class Network Portion of Address Broadcast Address Host PortionNetwork Address Network Class Network Bits Host Bits Netmask Private IP Networks and the Internet Network RFCs Binary to Hex Conversion Decimal Binary Hex Connect Mode Options UDP Hostlist Unconditionally Character No active startup Connect Mode Options for Modem Emulation Disconnect Mode Options Binary to Hex Flush Mode Buffer Flushing Options Active connection Enable Passive connection Disconnect Disconnect Active connection Passive connection Enable Active connection Disconnect Enable Passive connection Active connection Passive connection Disconnect Enable Passive connection Active connection Disconnect Enable Interface Mode Options Pack Control Options Byte Sequence 250ms Yes 5sec 12ms 52ms Page Class B Network IP AddressesClass a Network Class C Network Network Address Broadcast AddressIP Netmask Private IP Networks and the Internet Network RFCsPage Glossary of Terms AUI Bootp BNC Chap CSMA/CD Dhcp Fddi FTP Http LAN IPXIsdn LAT MII MAUMIB MMJ MOP NIC NOS PAP PPPProm Rmon ROM SNA RtelSlip Snmp TCP/IP SPXSQE 10BASE-T Tftp UTP