Power Requirements, Reset Switch | Lantronix 10 instruction

Introduction

1.13 Power Requirements

The UDS-10 is shipped with a 12VDC, 1A power supply, but any DC power supply between 9VDC and 30VDC can be used. You can order the UDS-10 with a 110VAC (UDS-10-01) or 230VAC (UDS-10-02) power supply.

Note: The input voltage for all UDS-10 products has been changed from 6-9VDC to 9- 30VDC. The new power supply shipped with the product supplies voltage within the new 9- 30VDC range. Please note that this new power supply should only be used with the 9-30VDC UDS-10 products. The correct input voltage is marked on a label above the power socket and on the back of the unit.

Power Socket

1.14 Reset Switch

The unit has a reset switch located next to the RJ-45 connector. This reset switch will reboot the UDS when pressed.

Reset Switch

1-12	UDS-10 User Guide

Image 26

Lantronix 10 manual Power Requirements, Reset Switch

Contents

UDS-10 User Guide Copyright and Trademark Disclaimer and Revisions Date Rev Author Comments Declaration of Conformity Warranty Sales Offices Table of Contents Server Configuration Network Configuration DeviceComm Manager 10.1 List of Figures UDS-10-IAP List of Tables Disconnect Mode Options Page Introduction UDS-10 UDS-10B UDS-10-IAP Device Server UDS-10-IAP Industrial Automation Protocols IP Address Network ProtocolsPacking Algorithm Port Number Serial Interface RJ-45 Ethernet Interface DIR PIN Signal NameEthernet Cable Primary Function Serial Interface Connection Meaning LEDsLED Software Support DimensionsProduct Information Label Power Requirements Reset Switch Technical Specifications Technical SpecsPage Ethernet MAC Address Getting StartedAddresses and Port Number Internet Protocol IP Address Physically Connecting the Unit UDS-10 Connected to Serial Device and Network Methods of Assigning the IP Address Method Description Dhcp AutoIP DeviceInstaller Install DeviceInstaller Software DeviceInstaller Window Assign IP Address and Network Class Test the IP Address Ping Device Window Add the Unit to the Manage List Search Network Window Devices in a Group Opening a Configuration Window Device Management Window ARP and Telnet Serial Port Login Configuring the Unit Configuring via Web Browser Using DeviceInstaller Configure Web Manager Web Manager 3.0 has the following buttons Unit Configuration Telnet Password Server Properties Port Properties Configure Update Settings Technical Support Configuring via the Setup Mode Window Using a Telnet Connection Setup Mode Window Set Gateway IP Address Server Configuration Network ConfigurationUsing the Serial Port Netmask Host Bits Netmask Number of Bits for Host PartNetwork Class Host Bits Netmask Change Telnet configuration password Dhcp Naming Mode Option Channel 1 Configuration Serial Port Parameters2 I/F Interface Mode Baudrate Common I/F Mode Setting Binary Hex Port Numbers Reserved for FlowFlow Control Option Hex Connect Mode Connect Mode Option Manual Connection Address Example Modem Mode Function Command ATD Remote Port Disconnect Mode OptionRemote IP Address DisConnMode Flush Mode Buffer Flushing Input Buffer Serial to Network Pack Control Pack Control Options Send Characters DisConnTime Inactivity TimeoutChannel Port Password Telnet Terminal Type Disable Snmp Expert SettingsSecurity Settings TCP Keepalive time in s Factory Defaults Exit Configuration Mode Get Configuration Set Configuration Updating Protocol Firmware Protocol Firmware Via DeviceInstaller Search Network Window Upgrade Firmware Via Tftp Via Another Unit Tftp Dialog Box Via the Serial Port DeviceComm Manager Installing DeviceComm Manager Install DeviceComm Manager Setup Status Meaning Firmware Troubleshooting Technical Support Troubleshooting Problems and Error Messages Firmware field UDS/CoBox Page Entering Monitor Mode Via the Serial Port Monitor ModeMonitor Mode Entering Monitor Mode Via the Network Port Command Command Name Function Response Meaning UDP Datagrams Network Configuration using UDPByte Command Parameters Byte Command Parameters Configuring Multiple Devices Acquiring a Valid Setup Record Sending a Setup Record Intel Hex Format Option Hex Calculating the Checksum Calculating the Two’s Complement Setup Records Bytes Function Channel Parameters Channel Parameters Interface Mode Option Binary Hex Speed Hex Bps Baud RateFlow Control Connect Mode Disconnect Mode Function 5 4 3 2 1 Option Subnet Portion IP AddressesNetwork Portion Network Class Network Portion of Address Broadcast Address Host PortionNetwork Address Network Class Network Bits Host Bits Netmask Private IP Networks and the Internet Network RFCs Binary to Hex Conversion Decimal Binary Hex Connect Mode Options UDP Hostlist Unconditionally Character No active startup Connect Mode Options for Modem Emulation Disconnect Mode Options Binary to Hex Flush Mode Buffer Flushing Options Active connection Enable Passive connection Disconnect Disconnect Active connection Passive connection Enable Active connection Disconnect Enable Passive connection Active connection Passive connection Disconnect Enable Passive connection Active connection Disconnect Enable Interface Mode Options Pack Control Options Byte Sequence 250ms Yes 5sec 12ms 52ms Page Class B Network IP AddressesClass a Network Class C Network IP Netmask Network AddressBroadcast Address Private IP Networks and the Internet Network RFCsPage Glossary of Terms AUI Bootp BNC Chap CSMA/CD Dhcp Fddi FTP Http LAN IPXIsdn LAT MII MAUMIB MMJ MOP NIC NOS Prom PAPPPP Rmon ROM SNA RtelSlip Snmp TCP/IP SPXSQE 10BASE-T Tftp UTP