Port Properties | Lantronix 10 specification

Configure

3.3.3 Port Properties

Serial Protocol: RS232, RS422/485 4-wire, RS485 2-wire

Speed: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200

Character Size: 8, 7

Parity: None, Even, Odd

Stop Bit: 1,2

Flow Control: None, XON/XOFF, XON/XOFF Pass Characters to Host, CTS/RTS (Hardware)

UDP Datagram Mode: Enable, Disable

UDP Datagram Type: (User selectable)

Incoming Connection: Accept unconditional, Accept Incoming/DTR (Inactive), Never accept incoming

Response: Nothing (quiet), Character response

Startup: No active startup, with any character, with active DTR (Inactive), with CR (0x0D) only, Manual Connection, Autostart, Modem Mode

Remote IP Address: (user selectable)

Remote Port: (user selectable)

Local Port: 10001 (default 10001, user selectable)

UDS-10 User Guide

3-7

Image 47

Lantronix 10 manual Port Properties

Contents

UDS-10 User Guide Copyright and Trademark Date Rev Author Comments Disclaimer and Revisions Declaration of Conformity Warranty Sales Offices Table of Contents Server Configuration Network Configuration DeviceComm Manager 10.1 UDS-10-IAP List of Figures List of Tables Disconnect Mode Options Page Introduction UDS-10 UDS-10B UDS-10-IAP UDS-10-IAP Device Server Industrial Automation Protocols Port Number Network ProtocolsPacking Algorithm IP Address RJ-45 Ethernet Interface Serial Interface Primary Function Signal NameEthernet Cable DIR PIN Serial Interface Connection Meaning LEDsLED Software Support DimensionsProduct Information Label Reset Switch Power Requirements Technical Specs Technical SpecificationsPage Internet Protocol IP Address Getting StartedAddresses and Port Number Ethernet MAC Address UDS-10 Connected to Serial Device and Network Physically Connecting the Unit Method Description Methods of Assigning the IP Address AutoIP Dhcp Install DeviceInstaller Software DeviceInstaller Assign IP Address and Network Class DeviceInstaller Window Ping Device Window Test the IP Address Search Network Window Add the Unit to the Manage List Devices in a Group Device Management Window Opening a Configuration Window ARP and Telnet Serial Port Login Configuring via Web Browser Configuring the Unit Using DeviceInstaller Configure Web Manager 3.0 has the following buttons Web Manager Unit Configuration Server Properties Telnet Password Port Properties Configure Technical Support Update Settings Using a Telnet Connection Configuring via the Setup Mode Window Setup Mode Window Set Gateway IP Address Server Configuration Network ConfigurationUsing the Serial Port Netmask Host Bits Netmask Number of Bits for Host PartNetwork Class Host Bits Netmask Dhcp Naming Change Telnet configuration password Baudrate Channel 1 Configuration Serial Port Parameters2 I/F Interface Mode Mode Option Common I/F Mode Setting Binary Hex Port Numbers Reserved for FlowFlow Control Option Hex Connect Mode Option Connect Mode Manual Connection Address Example ATD Modem Mode Function Command DisConnMode Disconnect Mode OptionRemote IP Address Remote Port Input Buffer Serial to Network Flush Mode Buffer Flushing Pack Control Options Pack Control Telnet Terminal Type DisConnTime Inactivity TimeoutChannel Port Password Send Characters TCP Keepalive time in s Expert SettingsSecurity Settings Disable Snmp Factory Defaults Get Configuration Exit Configuration Mode Set Configuration Protocol Firmware Updating Protocol Firmware Via DeviceInstaller Search Network Window Via Tftp Upgrade Firmware Tftp Dialog Box Via Another Unit Via the Serial Port DeviceComm Manager Install DeviceComm Manager Installing DeviceComm Manager Status Meaning Setup Firmware Technical Support Troubleshooting Troubleshooting Problems and Error Messages Firmware field UDS/CoBox Page Entering Monitor Mode Via the Network Port Monitor ModeMonitor Mode Entering Monitor Mode Via the Serial Port Response Meaning Command Command Name Function UDP Datagrams Network Configuration using UDPByte Command Parameters Byte Command Parameters Acquiring a Valid Setup Record Configuring Multiple Devices Sending a Setup Record Option Hex Intel Hex Format Calculating the Two’s Complement Calculating the Checksum Bytes Function Setup Records Channel Parameters Channel Parameters Option Binary Hex Interface Mode Speed Hex Bps Baud RateFlow Control Connect Mode Disconnect Mode Option Function 5 4 3 2 1 Network Class Network Portion of Address IP AddressesNetwork Portion Subnet Portion Network Class Network Bits Host Bits Netmask Host PortionNetwork Address Broadcast Address Network RFCs Private IP Networks and the Internet Decimal Binary Hex Binary to Hex Conversion UDP Connect Mode Options Hostlist Unconditionally Character No active startup Connect Mode Options for Modem Emulation Disconnect Mode Options Binary to Hex Flush Mode Buffer Flushing Options Active connection Enable Passive connection Disconnect Disconnect Active connection Passive connection Enable Active connection Disconnect Enable Passive connection Active connection Passive connection Disconnect Enable Passive connection Active connection Disconnect Enable Interface Mode Options Pack Control Options Byte Sequence 250ms Yes 5sec 12ms 52ms Page Class C Network IP AddressesClass a Network Class B Network IP Netmask Network AddressBroadcast Address Network RFCs Private IP Networks and the InternetPage AUI Glossary of Terms BNC Bootp Chap Dhcp CSMA/CD Fddi FTP Http LAT IPXIsdn LAN MMJ MAUMIB MII MOP NOS NIC Prom PAPPPP ROM Rmon Snmp RtelSlip SNA 10BASE-T SPXSQE TCP/IP Tftp UTP