Configure | Lantronix 10 specs

Configure

On Active Connection: Enable, Disable

On Passive Connection: Enable, Disable

At Time of Disconnect: Enable, Disable

Packing Algorithm: Enable, Disable

Idle Time: Force transmit 12 ms, Force transmit 52 ms, Force Transmit 250 ms, Force Transmit 5000 ms

Trailing Characters: None, One, Two

Send Immediate After Sendchars: Enable, Disable

Send Define2-Byte Sequence: Enable, Disable

Send Character 01: (User Selectable)

Send Character 02: (User Selectable)

3-8	UDS-10 User Guide

Image 48

Lantronix 10 manual Configure

Contents

UDS-10 User Guide Copyright and Trademark Disclaimer and Revisions Date Rev Author Comments Declaration of Conformity Warranty Sales Offices Table of Contents Server Configuration Network Configuration DeviceComm Manager 10.1 List of Figures UDS-10-IAP List of Tables Disconnect Mode Options Page Introduction UDS-10 UDS-10B UDS-10-IAP Device Server UDS-10-IAP Industrial Automation Protocols Network Protocols Packing AlgorithmIP Address Port Number Serial Interface RJ-45 Ethernet Interface Signal Name Ethernet CableDIR PIN Primary Function Serial Interface Connection LEDs LEDMeaning Dimensions Product Information LabelSoftware Support Power Requirements Reset Switch Technical Specifications Technical SpecsPage Getting Started Addresses and Port NumberEthernet MAC Address Internet Protocol IP Address Physically Connecting the Unit UDS-10 Connected to Serial Device and Network Methods of Assigning the IP Address Method Description Dhcp AutoIP DeviceInstaller Install DeviceInstaller Software DeviceInstaller Window Assign IP Address and Network Class Test the IP Address Ping Device Window Add the Unit to the Manage List Search Network Window Devices in a Group Opening a Configuration Window Device Management Window ARP and Telnet Serial Port Login Configuring the Unit Configuring via Web Browser Using DeviceInstaller Configure Web Manager Web Manager 3.0 has the following buttons Unit Configuration Telnet Password Server Properties Port Properties Configure Update Settings Technical Support Configuring via the Setup Mode Window Using a Telnet Connection Setup Mode Window Server Configuration Network Configuration Using the Serial PortSet Gateway IP Address Netmask Number of Bits for Host Part Network Class Host Bits NetmaskNetmask Host Bits Change Telnet configuration password Dhcp Naming Channel 1 Configuration Serial Port Parameters 2 I/F Interface ModeMode Option Baudrate Common I/F Mode Setting Binary Hex Flow Flow Control Option HexPort Numbers Reserved for Connect Mode Connect Mode Option Manual Connection Address Example Modem Mode Function Command ATD Disconnect Mode Option Remote IP AddressRemote Port DisConnMode Flush Mode Buffer Flushing Input Buffer Serial to Network Pack Control Pack Control Options DisConnTime Inactivity Timeout Channel Port PasswordSend Characters Telnet Terminal Type Expert Settings Security SettingsDisable Snmp TCP Keepalive time in s Factory Defaults Exit Configuration Mode Get Configuration Set Configuration Updating Protocol Firmware Protocol Firmware Via DeviceInstaller Search Network Window Upgrade Firmware Via Tftp Via Another Unit Tftp Dialog Box Via the Serial Port DeviceComm Manager Installing DeviceComm Manager Install DeviceComm Manager Setup Status Meaning Firmware Troubleshooting Technical Support Troubleshooting Problems and Error Messages Firmware field UDS/CoBox Page Monitor Mode Monitor ModeEntering Monitor Mode Via the Serial Port Entering Monitor Mode Via the Network Port Command Command Name Function Response Meaning Network Configuration using UDP Byte Command ParametersUDP Datagrams Byte Command Parameters Configuring Multiple Devices Acquiring a Valid Setup Record Sending a Setup Record Intel Hex Format Option Hex Calculating the Checksum Calculating the Two’s Complement Setup Records Bytes Function Channel Parameters Channel Parameters Interface Mode Option Binary Hex Baud Rate Flow ControlSpeed Hex Bps Connect Mode Disconnect Mode Function 5 4 3 2 1 Option IP Addresses Network PortionSubnet Portion Network Class Network Portion of Address Host Portion Network AddressBroadcast Address Network Class Network Bits Host Bits Netmask Private IP Networks and the Internet Network RFCs Binary to Hex Conversion Decimal Binary Hex Connect Mode Options UDP Hostlist Unconditionally Character No active startup Connect Mode Options for Modem Emulation Disconnect Mode Options Binary to Hex Flush Mode Buffer Flushing Options Active connection Enable Passive connection Disconnect Disconnect Active connection Passive connection Enable Active connection Disconnect Enable Passive connection Active connection Passive connection Disconnect Enable Passive connection Active connection Disconnect Enable Interface Mode Options Pack Control Options Byte Sequence 250ms Yes 5sec 12ms 52ms Page IP Addresses Class a NetworkClass B Network Class C Network Network Address Broadcast AddressIP Netmask Private IP Networks and the Internet Network RFCsPage Glossary of Terms AUI Bootp BNC Chap CSMA/CD Dhcp Fddi FTP Http IPX IsdnLAN LAT MAU MIBMII MMJ MOP NIC NOS PAP PPPProm Rmon ROM Rtel SlipSNA Snmp SPX SQETCP/IP 10BASE-T Tftp UTP