Dimensions, Product Information Label | Lantronix 10 manual

Introduction

1.10 Dimensions

The UDS-10 dimensions are shown in the following drawing.

Note: For UDS-10 and UDS-10-IAP.

6.4cm (2.5 in)

9 cm (3.5 in)

2.3cm (0.9 in)

1.11Product Information Label

The product information label contains important information about your specific unit.

S/N:2447938

UDS-10B

00-20-4A-24-BB-42 Rev. D12

Made in USA

Serial Number

Part Number

MAC ID

Revision

1.12 Software Support

DeviceInstaller is a powerful software utility for configuring device servers from a network connection. For more information, see Using DeviceInstaller on page 3-2.

Lantronix DeviceComm Manager is a Windows based COM port redirector software utility. Its function is to redirect customer application data destined for a local serial (COM) port to the PC’s network port. Rather than going out the local port, the data is transmitted across the Ethernet network port using the TCP/IP protocol. For more information, see DeviceComm Manager on page 5-1.

UDS-10 User Guide

1-11

Image 25

Lantronix 10 manual Dimensions, Product Information Label, Software Support

Contents

UDS-10 User Guide Copyright and Trademark Date Rev Author Comments Disclaimer and Revisions Declaration of Conformity Warranty Sales Offices Table of Contents Server Configuration Network Configuration DeviceComm Manager 10.1 UDS-10-IAP List of Figures List of Tables Disconnect Mode Options Page Introduction UDS-10 UDS-10B UDS-10-IAP UDS-10-IAP Device Server Industrial Automation Protocols Packing Algorithm Network ProtocolsIP Address Port Number RJ-45 Ethernet Interface Serial Interface Ethernet Cable Signal NameDIR PIN Primary Function Serial Interface Connection LED LEDsMeaning Product Information Label DimensionsSoftware Support Reset Switch Power Requirements Technical Specs Technical SpecificationsPage Addresses and Port Number Getting StartedEthernet MAC Address Internet Protocol IP Address UDS-10 Connected to Serial Device and Network Physically Connecting the Unit Method Description Methods of Assigning the IP Address AutoIP Dhcp Install DeviceInstaller Software DeviceInstaller Assign IP Address and Network Class DeviceInstaller Window Ping Device Window Test the IP Address Search Network Window Add the Unit to the Manage List Devices in a Group Device Management Window Opening a Configuration Window ARP and Telnet Serial Port Login Configuring via Web Browser Configuring the Unit Using DeviceInstaller Configure Web Manager 3.0 has the following buttons Web Manager Unit Configuration Server Properties Telnet Password Port Properties Configure Technical Support Update Settings Using a Telnet Connection Configuring via the Setup Mode Window Setup Mode Window Using the Serial Port Server Configuration Network ConfigurationSet Gateway IP Address Network Class Host Bits Netmask Netmask Number of Bits for Host PartNetmask Host Bits Dhcp Naming Change Telnet configuration password 2 I/F Interface Mode Channel 1 Configuration Serial Port ParametersMode Option Baudrate Common I/F Mode Setting Binary Hex Flow Control Option Hex FlowPort Numbers Reserved for Connect Mode Option Connect Mode Manual Connection Address Example ATD Modem Mode Function Command Remote IP Address Disconnect Mode OptionRemote Port DisConnMode Input Buffer Serial to Network Flush Mode Buffer Flushing Pack Control Options Pack Control Channel Port Password DisConnTime Inactivity TimeoutSend Characters Telnet Terminal Type Security Settings Expert SettingsDisable Snmp TCP Keepalive time in s Factory Defaults Get Configuration Exit Configuration Mode Set Configuration Protocol Firmware Updating Protocol Firmware Via DeviceInstaller Search Network Window Via Tftp Upgrade Firmware Tftp Dialog Box Via Another Unit Via the Serial Port DeviceComm Manager Install DeviceComm Manager Installing DeviceComm Manager Status Meaning Setup Firmware Technical Support Troubleshooting Troubleshooting Problems and Error Messages Firmware field UDS/CoBox Page Monitor Mode Monitor ModeEntering Monitor Mode Via the Serial Port Entering Monitor Mode Via the Network Port Response Meaning Command Command Name Function Byte Command Parameters Network Configuration using UDPUDP Datagrams Byte Command Parameters Acquiring a Valid Setup Record Configuring Multiple Devices Sending a Setup Record Option Hex Intel Hex Format Calculating the Two’s Complement Calculating the Checksum Bytes Function Setup Records Channel Parameters Channel Parameters Option Binary Hex Interface Mode Flow Control Baud RateSpeed Hex Bps Connect Mode Disconnect Mode Option Function 5 4 3 2 1 Network Portion IP AddressesSubnet Portion Network Class Network Portion of Address Network Address Host PortionBroadcast Address Network Class Network Bits Host Bits Netmask Network RFCs Private IP Networks and the Internet Decimal Binary Hex Binary to Hex Conversion UDP Connect Mode Options Hostlist Unconditionally Character No active startup Connect Mode Options for Modem Emulation Disconnect Mode Options Binary to Hex Flush Mode Buffer Flushing Options Active connection Enable Passive connection Disconnect Disconnect Active connection Passive connection Enable Active connection Disconnect Enable Passive connection Active connection Passive connection Disconnect Enable Passive connection Active connection Disconnect Enable Interface Mode Options Pack Control Options Byte Sequence 250ms Yes 5sec 12ms 52ms Page Class a Network IP AddressesClass B Network Class C Network Broadcast Address Network AddressIP Netmask Network RFCs Private IP Networks and the InternetPage AUI Glossary of Terms BNC Bootp Chap Dhcp CSMA/CD Fddi FTP Http Isdn IPXLAN LAT MIB MAUMII MMJ MOP NOS NIC PPP PAPProm ROM Rmon Slip RtelSNA Snmp SQE SPXTCP/IP 10BASE-T Tftp UTP