Manuals
/
Brands
/
Computer Equipment
/
Network Card
/
Lantronix
/
Computer Equipment
/
Network Card
Lantronix
10
- page 122
1
122
139
139
Download
139 pages, 875.31 Kb
Contents
Main
UDS-10 User Guide
Copyright and Trademark
Disclaimer and Revisions
Declaration of Conformity
Warranty
Sales Offices
Table of Contents
Page
Page
Page
List of Figures
List of Tables
Page
Page
1. Introduction
1.1 UDS-10
1.2 UDS-10B
1.3 UDS-10-IAP Device Server
1.3.1 Industrial Automation Protocols
1.4 Network Protocols
1.4.1 Packing Algorithm
1.4.2 IP Address
1.4.3 Port Number
1.5 Serial Interface
1.6 RJ-45 Ethernet Interface
1.7 Ethernet Cable
Introduction
UDS-10 User Guide 1-9
1.8 Serial Interface Connection
DTE, 9-Pin, FEMALE
RX(in)
TX(in)
1.9 LEDs
The device contains the following LEDs:
link net Tx/Rx collision diagnostic status
Table 2 - UDS-10 LED Functions LED Meaning
1.10 Dimensions
1.11 Product Information Label
1.12 Software Support
1.13 Power Requirements
1.14 Reset Switch
1.15 Technical Specifications
Table 3 - Technical Specs
Page
2. Getting Started
2.1 Addresses and Port Number
2.1.1 Ethernet (MAC) Address
2.1.2 Internet Protocol (IP) Address
2.1.3 Port Number
2.2 Physically Connecting the Unit
2.3 Methods of Assigning the IP Address
2.3.1 DHCP
2.3.2 AutoIP
2.4 DeviceInstaller
2.4.1 Install DeviceInstaller Software
2.4.2 Assign IP Address and Network Class
2.4.3 Test the IP Address
2.4.4 Add the Unit to the Manage List
Page
2.4.5 Opening a Configuration Window
2.5 ARP and Telnet
2.6 Serial Port Login
3. Configuring the Unit
3.1 Configuring via Web Browser
3.2 Using DeviceInstaller
Page
3.3 Web Manager Page
3.3.1 Unit Configuration
3.3.2 Server Properties
3.3.3 Port Properties
Page
3.3.4 Technical Support
3.3.5 Update Settings
3.4 Configuring via the Setup Mode Window
3.4.1 Using a Telnet Connection
Configure
Figure 13 - Setup Mode Window
UDS-10 User Guide 3-11
3.4.2 Using the Serial Port
3.5 Server Configuration (Network Configuration)
3.5.1 IP Address
3.5.2 Set Gateway IP Address
3.5.3 Netmask: Number of Bits for Host Part
3.5.4 Change Telnet configuration password
3.5.5 DHCP Naming
3.6 Channel 1 Configuration (Serial Port Parameters)
3.6.1 Baudrate
3.6.2 I/F (Interface) Mode
Page
3.6.3 Flow
3.6.4 Port Number
3.6.5 Connect Mode
Page
Page
3.6.6 Remote IP Address
3.6.7 Remote Port
3.6.8 DisConnMode
3.6.9 Flush Mode (Buffer Flushing)
3.6.10 Pack Control
3.6.11 DisConnTime (Inactivity Timeout)
3.6.12 Send Characters
3.6.13 Telnet Terminal Type
3.6.14 Channel (Port) Password
3.7 Expert Settings
3.7.1 TCP Keepalive time in s
3.8 Security Settings
3.8.1 Disable SNMP
3.8.2 SNMP Community Name
3.9 Factory Defaults
Page
3.12 Set Configuration
4. Updating Protocol (Firmware)
4.1 Protocol Firmware
4.2 Reloading Protocol Firmware
4.2.1 Via DeviceInstaller
Page
4.2.2 Via TFTP
4.2.3 Via Another Unit
4.2.4 Via the Serial Port
5. DeviceComm Manager
5.1 Installing DeviceComm Manager
5.1.1 Install DeviceComm Manager
5.1.2 Setup
Page
6. Troubleshooting
6.1 Technical Support
6.1.1 Technical Support
Page
Troubleshooting
UDS-10 User Guide 6-3
Table 16 - Problems and Error Messages
Problem/Message Reason Solution
Troubleshooting
6-4 UDS-10 User Guide
Problem/Message Reason Solution
Troubleshooting
UDS-10 User Guide 6-5
Problem/Message Reason Solution
Page
7. Monitor Mode
7.1 Monitor Mode
7.1.1 Entering Monitor Mode Via the Serial Port
7.1.2 Entering Monitor Mode Via the Network Port
7.1.3 Monitor Mode Commands
Table 17 - Monitor Mode Commands Command Command Name Function
8. Network Configuration using UDP
8.1 UDP Datagrams
Byte Command Parameters Notes
8.2 Configuring Multiple Devices
8.2.1 Acquiring a Valid Setup Record
8.2.2 Sending a Setup Record
8.2.3 The Intel Hex Format
8.2.4 Calculating the Checksum
8.2.5 Calculating the Twos Complement
8.3 Setup Records
8.3.1 Channel Parameters
8.3.2 Interface Mode
8.3.3 Baud Rate
8.3.4 Flow Control
8.3.5 Connect Mode
8.3.6 Disconnect Mode
8.3.7 Flush Mode (Buffer Flushing)
8.3.8 Pack Control
8.4 IP Addresses
8.4.1 Network Portion
8.4.2 Subnet Portion
8.4.3 Host Portion
8.4.4 Network Address
8.4.5 Broadcast Address
8.4.6 Private IP Networks and the Internet
8.4.7 Network RFCs
9. Binary to Hex Conversion
Binary to Hex
9-2 UDS-10 User Guide
9.1 Connect Mode Options
Binary to Hex
UDS-10 User Guide 9-3
Binary to Hex
9-4 UDS-10 User Guide
Accept Incoming Connections
Response Hex
9.2 Disconnect Mode Options
Page
Binary to Hex
UDS-10 User Guide 9-7
9.3 Flush Mode (Buffer Flushing) Options
Table 39 - Flush Mode Options
Serial to Network Clear input buffer upon:
Network to Serial Clear output buffer upon:
Alternate Packing Algorithm
Page
Page
Page
Page
Page
Binary to Hex
UDS-10 User Guide 9-13
9.4 Interface Mode Options
Table 40 - Interface Mode Options
Interface Bits Parity Stop Bits
Hex
Binary to Hex
9.5 Pack Control Options
Table 41 - Pack Control Options
Page
Page
10. IP Addresses
10.1 Class A Network
10.2 Class B Network
10.3 Class C Network
10.4 Network Address
10.5 Broadcast Address
10.6 IP Netmask
10.7 Private IP Networks and the Internet
10.8 Network RFCs
Page
11. Glossary of Terms