Lantronix 10 8.2.2 Sending a Setup Record

UDP

8-4 UDS-10 User Guide

To request the setup record of a properly configured Device Server via another Device Server

on the network:

5. Make sure that both units are plugged onto the network properly.

6. Enter Monitor Mode (with network support enabled) on the unit that is not properly

configured. (see Monitor Mode on page 7-1)

7. Issue the command GC x.x.x.x followed by a carriage return, where x.x.x.x is the IP

address of the properly configured device. The properly configured device will respond

by sending its setup record to the unit you are currently on. This configuration will be

displayed in Intel HEX format.

8. Copy that HEX string, and then issue the command SC. Now paste the copied string.

The unit will not reboot on its own. You must reboot the unit before the settings take effect.

To build the setup record in software:

1. Create a 120-byte setup record.

2. Convert it to an Intel Hex record (see The Intel Hex Format on page 8-5).

3. Copy the setup record into a text file and save it for future use.

To request the setup record of a properly configured Device Server via UDP:

1. Configure a Device Server with the desired parameters and place it on the network.

2. From a host PC, send the F8 datagram to the Device Server (see Network Configuration

using UDP on page 8-1). The Device Server responds with the F9 datagram, which

includes its setup record.

3. Send a previously saved setup record from a host PC via UDP.

8.2.2 Sending a Setup Record

There are also a number of ways to send a setup record to a Device Server:

• Send a previously saved setup record via Monitor Mode (easiest method).

• Send the setup record of a properly configured Device Server to another Device

Server on the network.

• Send a previously saved setup record from a host PC via UDP.

Contents

Main UDS-10 User Guide Copyright and Trademark Disclaimer and Revisions Declaration of Conformity Warranty Sales Offices Table of Contents Page Page Page List of Figures List of Tables Page Page 1. Introduction 1.1 UDS-10 1.2 UDS-10B 1.3 UDS-10-IAP Device Server 1.3.1 Industrial Automation Protocols 1.4 Network Protocols 1.4.1 Packing Algorithm 1.4.2 IP Address 1.4.3 Port Number 1.5 Serial Interface 1.6 RJ-45 Ethernet Interface 1.7 Ethernet Cable Introduction UDS-10 User Guide 1-9 1.8 Serial Interface Connection DTE, 9-Pin, FEMALE RX(in) TX(in) 1.9 LEDs The device contains the following LEDs: link net Tx/Rx collision diagnostic status Table 2 - UDS-10 LED Functions LED Meaning 1.10 Dimensions 1.11 Product Information Label 1.12 Software Support 1.13 Power Requirements 1.14 Reset Switch 1.15 Technical Specifications Table 3 - Technical Specs Page 2. Getting Started 2.1 Addresses and Port Number 2.1.1 Ethernet (MAC) Address 2.1.2 Internet Protocol (IP) Address 2.1.3 Port Number 2.2 Physically Connecting the Unit 2.3 Methods of Assigning the IP Address 2.3.1 DHCP 2.3.2 AutoIP 2.4 DeviceInstaller 2.4.1 Install DeviceInstaller Software 2.4.2 Assign IP Address and Network Class 2.4.3 Test the IP Address 2.4.4 Add the Unit to the Manage List Page 2.4.5 Opening a Configuration Window 2.5 ARP and Telnet 2.6 Serial Port Login 3. Configuring the Unit 3.1 Configuring via Web Browser 3.2 Using DeviceInstaller Page 3.3 Web Manager Page 3.3.1 Unit Configuration 3.3.2 Server Properties 3.3.3 Port Properties Page 3.3.4 Technical Support 3.3.5 Update Settings 3.4 Configuring via the Setup Mode Window 3.4.1 Using a Telnet Connection Configure Figure 13 - Setup Mode Window UDS-10 User Guide 3-11 3.4.2 Using the Serial Port 3.5 Server Configuration (Network Configuration) 3.5.1 IP Address 3.5.2 Set Gateway IP Address 3.5.3 Netmask: Number of Bits for Host Part 3.5.4 Change Telnet configuration password 3.5.5 DHCP Naming 3.6 Channel 1 Configuration (Serial Port Parameters) 3.6.1 Baudrate 3.6.2 I/F (Interface) Mode Page 3.6.3 Flow 3.6.4 Port Number 3.6.5 Connect Mode Page Page 3.6.6 Remote IP Address 3.6.7 Remote Port 3.6.8 DisConnMode 3.6.9 Flush Mode (Buffer Flushing) 3.6.10 Pack Control 3.6.11 DisConnTime (Inactivity Timeout) 3.6.12 Send Characters 3.6.13 Telnet Terminal Type 3.6.14 Channel (Port) Password 3.7 Expert Settings 3.7.1 TCP Keepalive time in s 3.8 Security Settings 3.8.1 Disable SNMP 3.8.2 SNMP Community Name 3.9 Factory Defaults Page 3.12 Set Configuration 4. Updating Protocol (Firmware) 4.1 Protocol Firmware 4.2 Reloading Protocol Firmware 4.2.1 Via DeviceInstaller Page 4.2.2 Via TFTP 4.2.3 Via Another Unit 4.2.4 Via the Serial Port 5. DeviceComm Manager 5.1 Installing DeviceComm Manager 5.1.1 Install DeviceComm Manager 5.1.2 Setup Page 6. Troubleshooting 6.1 Technical Support 6.1.1 Technical Support Page Troubleshooting UDS-10 User Guide 6-3 Table 16 - Problems and Error Messages Problem/Message Reason Solution Troubleshooting 6-4 UDS-10 User Guide Problem/Message Reason Solution Troubleshooting UDS-10 User Guide 6-5 Problem/Message Reason Solution Page 7. Monitor Mode 7.1 Monitor Mode 7.1.1 Entering Monitor Mode Via the Serial Port 7.1.2 Entering Monitor Mode Via the Network Port 7.1.3 Monitor Mode Commands Table 17 - Monitor Mode Commands Command Command Name Function 8. Network Configuration using UDP 8.1 UDP Datagrams Byte Command Parameters Notes 8.2 Configuring Multiple Devices 8.2.1 Acquiring a Valid Setup Record 8.2.2 Sending a Setup Record 8.2.3 The Intel Hex Format 8.2.4 Calculating the Checksum 8.2.5 Calculating the Twos Complement 8.3 Setup Records 8.3.1 Channel Parameters 8.3.2 Interface Mode 8.3.3 Baud Rate 8.3.4 Flow Control 8.3.5 Connect Mode 8.3.6 Disconnect Mode 8.3.7 Flush Mode (Buffer Flushing) 8.3.8 Pack Control 8.4 IP Addresses 8.4.1 Network Portion 8.4.2 Subnet Portion 8.4.3 Host Portion 8.4.4 Network Address 8.4.5 Broadcast Address 8.4.6 Private IP Networks and the Internet 8.4.7 Network RFCs 9. Binary to Hex Conversion Binary to Hex 9-2 UDS-10 User Guide 9.1 Connect Mode Options Binary to Hex UDS-10 User Guide 9-3 Binary to Hex 9-4 UDS-10 User Guide Accept Incoming Connections Response Hex 9.2 Disconnect Mode Options Page Binary to Hex UDS-10 User Guide 9-7 9.3 Flush Mode (Buffer Flushing) Options Table 39 - Flush Mode Options Serial to Network Clear input buffer upon: Network to Serial Clear output buffer upon: Alternate Packing Algorithm Page Page Page Page Page Binary to Hex UDS-10 User Guide 9-13 9.4 Interface Mode Options Table 40 - Interface Mode Options Interface Bits Parity Stop Bits Hex Binary to Hex 9.5 Pack Control Options Table 41 - Pack Control Options Page Page 10. IP Addresses 10.1 Class A Network 10.2 Class B Network 10.3 Class C Network 10.4 Network Address 10.5 Broadcast Address 10.6 IP Netmask 10.7 Private IP Networks and the Internet 10.8 Network RFCs Page 11. Glossary of Terms