PRELIMINARYCY14B101P

Pinouts

Figure 1. Pin Diagram - 16-Pin SOIC

 

 

NC

 

 

1

16

 

 

VCC

 

 

 

 

 

 

 

 

 

 

 

 

VRTCbat

 

2

15

 

 

INT

 

 

 

 

Xout

 

3

14

 

 

VCAP

 

 

 

 

 

 

 

 

 

 

Xin

 

4

Top View 13

 

 

SO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

not to scale

 

 

SI

 

 

WP

 

 

 

5

12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

 

SCK

HOLD

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VRTCcap

 

7

10

 

 

 

 

 

 

 

CS

 

 

 

 

 

 

 

 

 

 

 

GND

 

8

9

 

 

 

 

 

 

HSB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Table 1. Pin Definitions

Pin Name

I/O Type

 

 

Description

 

 

 

 

 

 

 

 

 

Input

 

Chip Select. Activates the device when pulled LOW. Driving this pin HIGH puts the device in low

 

 

 

 

CS

 

 

 

 

 

 

 

 

 

 

 

power standby mode.

 

 

SCK

Input

 

Serial Clock. Runs at speeds up to a maximum of 25 MHz. All inputs are latched at the rising edge

 

 

 

 

 

 

 

 

 

 

 

of this clock. Outputs are driven at the falling edge of the clock.

 

 

 

 

SI

Input

 

Serial Input. Pin for input of all SPI instructions and data.

 

 

 

 

 

 

 

 

 

 

SO

Output

 

Serial Output. Pin for output of data through SPI.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Input

 

Write Protect. Implements hardware write protection in SPI.

 

 

 

WP

 

HOLD

 

Input

 

HOLD

Pin. Suspends Serial Operation.

 

 

 

 

 

 

 

 

Input/Output

 

Hardware Store Busy: A weak internal pull up keeps this pin pulled HIGH. If not used, this pin is

 

 

HSB

 

 

 

 

 

 

 

 

 

 

 

 

left as No Connect.

 

 

 

 

 

 

 

 

 

 

 

Output: Indicates busy status of nvSRAM when LOW.

 

 

 

 

 

 

 

 

 

 

 

Input: Hardware Store implemented by pulling this pin LOW externally.

 

VCAP

Power Supply

 

AutoStore Capacitor. Supplies power to the nvSRAM during power loss to STORE data from the

 

 

 

 

 

 

 

 

 

 

 

SRAM to nonvolatile elements. If AutoStore is not needed, this pin must be left as No Connect. It

 

 

 

 

 

 

 

 

 

 

 

must never be connected to GND.

VRTCcap

Power Supply

 

Capacitor Backup for RTC. Left unconnected if VRTCbat is used.

VRTCbat

Power Supply

 

Battery Backup for RTC. Left unconnected if VRTCcap is used.

 

 

Xout

Output

 

Crystal Output connection. Drives crystal on start up.

 

 

 

 

 

 

 

 

 

 

Xin

Input

 

Crystal Input connection. For 32.768 kHz crystal.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INT

Output

 

Interrupt Output. Programmable to respond to the clock alarm, the watchdog timer, and the power

 

 

 

 

 

monitor. Also programmable to either active HIGH (push or pull) or LOW (open drain).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NC

No Connect

 

No Connect. This pin is not connected to the die.

 

 

 

 

 

GND

Power Supply

Ground

 

 

 

 

 

 

 

VCC

Power Supply

Power Supply (2.7-3.6V)

Document #: 001-44109 Rev. *B

Page 2 of 32

[+] Feedback

Page 2
Image 2
Cypress CY14B101P manual Pinouts, Pin Definitions Pin Name Type Description, Hold