Datalogic Scanning 6000 PLUS guide

IBM 4683/84 • 4693/94 Port 9A, 9B, 9C, 9E I/F Selection

Scan this label to enable the IBM 468x/9x Port 9x interface.

IBM 4683/84 • 4693/94 Port 9A, 9B, 9C, 9E Settings

Data Format: Send As Code 39 — converts bar code data (UPC/EAN, add-ons, Code 93, Codabar, MSI/Plessey and Code 128) into Code 39 format before sending the data to the host.

These settings are for IBM 4683/84 • 4693/94 Port 9A, 9B, 9C, 9E inter- face ONLY.

Limit Command Set — is an option that causes the scanner to ignore 'enable scanner' and 'disable scanner' commands sent from the host.

Transmit Unsolicited Status1 — when enabled, this option causes the scanner to transmit a status message to the host upon receipt of an "SNRM".

SET

DATA FORMAT

----------------------------------------------

SEND AS CODE 39 ----------------

DON'T SEND AS CODE 39 --------

ENABLE LIMIT COMMAND SET -----

DISABLE LIMIT COMMAND SET -----

TRANSMIT UNSOLICITED STATUS ---

DON'T TRANSMIT UNSOLICITED STATUS ---

END ----------------------------------------------

1 For this IBM interface, the setting for Unsolicited Status is normally Disabled.

10	QuickScan 6000/6000 Plus

Image 14

Datalogic Scanning 6000 PLUS manual IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E I/F Selection

Contents

QuickScan 6000/6000 Plus Datalogic Scanning, Inc Contents Sample Bar Codes SymbologiesAdditional Information Understanding the Basics Integrating Peripherals With Host Systems Software Changing InterfacesHardware RS-232 Wand Emulation Keyboard Wedge Customizing Your Scanner Operation Programming Overview What Is Programming Mode?How To Program Using Bar Codes Scanner Response When In Programming Mode Programming Session Return to Factory Settings If You Make a Mistake Where To Go From Here Send AS Code Dont Send AS Code IBM 4683/84 4693/94 Port 5B SettingsIBM 4683/84 4693/94 Port 5B Interface Selection END IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E Settings IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E I/F Selection IBM 4682/92 Port E Settings IBM 4682/92 Port E Interface Selection SNI Ocia Interface Selection Datalogic OCIA1 Interface SelectionNCR Ocia Nine Bit long format Interface Selection Enable Disable END Ocia Options Transmit in C39 Wand Emulation SettingsWand Emulation Interface Selection LOW High Transmit PRE-NOISE RS-232 Communication Parameters RS-232 Interface SelectionSNI RS-232 Interface Selection Baud Rate Data Format Table Data Format Settings None Even ODD Mark Space ONE TWO Seven Bits Eight Bits END Hardware Control Handshaking Enable XON/ Xoff Disable XON/XOFF END SET Disable ACK/NAK These features available for QuickScan 6000 Plus only Intercharacter Delay = 90 Milliseconds = 100 Milliseconds END PC Keyboard Wedge Interface Selection Keyboard Wedge Communication Parameters T YPE Keyboard Attached Enable Disable END PC Keyboard Wedge Connect to a Laptop/No Keyboard Attached Caps Lock QuickScan 6000 Plus only SET Caps Lock OFF Caps Lock on Country Mode QuickScan 6000 Plus only Country Mode QuickScan 6000 Plus only Spain Sweden Switzerland Japanese 106-KEY END Intercharacter Delay Intercharacter Delay RS-232 and Keyboard Wedge Interfaces Only Prefix & Suffix Programming Guide SET SET Prefix Non-Symbology Specific ItemsSetting Non-Symbology Specific Prefixes SET SET Suffix Setting Non-Symbology Specific SuffixesEntering Programming Mode Setting a Single Character Prefix or Suffix Setting Prefix and/or Suffix Characters ONE Character only Ascii Character Set Industry Standard Label Identifiers all are prefixes Symbology-Specific Label I.DSetting Symbology-Specific Label Identifiers Label I.D Setting Symbology Specific Label Identifiers Label I.D Label I.D. Symbology Selection EAN-13 W/C128 ADD- on EAN-13 W/2 Digit ADD- onEAN-13 W/5 Digit ADD- on ODE How to Set Single Character Label I.D This example 8 equals 38hex Disabling Label I.D. for a Specific Symbology Symbology Specific Label Identifiers Characters END Symbologies Symbology Options Overview Standard 2 of 5 must be enabled before Iata can be enabled Universal Symbology SelectionEnable All Symbologies Disable All Symbologies1 Symbology Selection SET Enable UPC/EAN Disable UPC/EAN Enable Code Disable Code Enable IATA3 Disable Iata Enable Codabar Disable Codabar Enable Code Disable Code Enable MSI/PLESSEY Disable MSI/PLESSEY UPC/EAN Options Dont Expand END UPC/EAN ExpansionDont Expand EXPAND1 C128 and Custom Add-Ons Optional Required Disabled ENDUPC/EAN Add-Ons UPC Data Format Settings Price/Weight Check DigitEnable 4 Digit Check Enable 5 Digit Check Send NSD2 Dont Send NSD2 END Send Check DigitSend NSD1 Dont Send NSD1 Send Check DIGIT2 EAN Data Format Settings Code 39 Options Dont Compute Dont Transmit Enable Disable END Code Setting Lengths END AIM Symbology ID Prefix Code 128 Options Interleaved 2 Interleaved 2 of 5 Label Lengths Check Digit and Variable Length Label Selections Setting Minimum Label Length Setting Interleaved 2 of 5 Fixed and Minimum Label LengthsSetting Fixed Lengths Set Fixed SET First Fixed Length Standard 2 Standard 2 of 5 Label Lengths Check Digit and Variable Length Label Selections Setting Standard 2 of 5 Fixed and Minimum Label Lengths Standard 2 of 5 Fixed and Minimum Label Lengths 5 Fixed Abel Lengths Tandard Minimum Codabar Options Codabar Check Digit & Variable Length Codabar Start/Stop Character Format = abcd/abcd END Enable Fixed Codabar Fixed Length Codabar SET Fixed Lengths MSI/Plessey Check Digit ONE Check Digit TWO Check Digits END MSI/Plessey Fixed Length MSI/PLESSEY SET Fixed Lengths General Features Good Read Beeper Settings OFF Read Verification Universal Read Verification Verify Code Read Verification by SymbologyVerify UPC-A Verify UPC-E Verify EAN-8 Verify EAN-13 Verify Interleaved 2 Low Power Mode Disable LOW Power Idle Debug Mode AutoSense Stand Mode Need More Information? Host ProgrammingCreating MultiFunction Labels Appendix B Sample Bar Codes UPC-E QuickScan 6000/6000 Plus Default Wand Keyboard Symbology RS-232 I/F Code 128 Options Transmit Don’t Transmit Codabar Options ABCD/ABCD Page Australia