General Features | Datalogic Scanning 6000 PLUS guide

General Features

The following section contains the general features that are common to all interfaces. These features allow modification of the scanner's behavior to accomodate user preferences.

Good Read Beeper Settings

These labels provide options for the scanner's audible 'beep' signal.

Audible Signal — enables/disables the beep upon completion of a good read.

NOTE

It is strongly recommended that this feature remain enabled, as the good read beep provides the best scanning status feedback to the user. Error tones are always enabled and cannot be disabled.

Power-up Beep — when enabled, beeps upon scanner power-up.

Beeper Volume — allows setting of the beeper to NORMAL or HIGH volume.

Good Read Beep Duration — can be adjusted to short (100msec), medium (250msec), or long (500msec) durations.

When to Beep — may be programmed to announce a 'good read' upon completion of one of the following events:

•Decode of a bar code's label

•Transmission from the scanner to the host

•CTS activation at the host terminal (RS-232 models ONLY)

80	QuickScan 6000/6000 Plus

Image 84

Datalogic Scanning 6000 PLUS manual General Features, Good Read Beeper Settings

Contents

QuickScan 6000/6000 Plus Datalogic Scanning, Inc Contents Symbologies Additional InformationSample Bar Codes Understanding the Basics Integrating Peripherals With Host Systems Changing Interfaces HardwareSoftware RS-232 Wand Emulation Keyboard Wedge Customizing Your Scanner Operation What Is Programming Mode? How To Program Using Bar CodesProgramming Overview Scanner Response When In Programming Mode Programming Session Return to Factory Settings If You Make a Mistake Where To Go From Here IBM 4683/84 4693/94 Port 5B Settings IBM 4683/84 4693/94 Port 5B Interface SelectionSend AS Code Dont Send AS Code END IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E Settings IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E I/F Selection IBM 4682/92 Port E Settings IBM 4682/92 Port E Interface Selection Datalogic OCIA1 Interface Selection NCR Ocia Nine Bit long format Interface SelectionSNI Ocia Interface Selection Enable Disable END Ocia Options Wand Emulation Settings Wand Emulation Interface SelectionTransmit in C39 LOW High Transmit PRE-NOISE RS-232 Interface Selection SNI RS-232 Interface SelectionRS-232 Communication Parameters Baud Rate Data Format Table Data Format Settings None Even ODD Mark Space ONE TWO Seven Bits Eight Bits END Hardware Control Handshaking Enable XON/ Xoff Disable XON/XOFF END SET Disable ACK/NAK These features available for QuickScan 6000 Plus only Intercharacter Delay = 90 Milliseconds = 100 Milliseconds END PC Keyboard Wedge Interface Selection Keyboard Wedge Communication Parameters T YPE Keyboard Attached Enable Disable END PC Keyboard Wedge Connect to a Laptop/No Keyboard Attached Caps Lock QuickScan 6000 Plus only SET Caps Lock OFF Caps Lock on Country Mode QuickScan 6000 Plus only Country Mode QuickScan 6000 Plus only Spain Sweden Switzerland Japanese 106-KEY END Intercharacter Delay Intercharacter Delay RS-232 and Keyboard Wedge Interfaces Only Prefix & Suffix Programming Guide Non-Symbology Specific Items Setting Non-Symbology Specific PrefixesSET SET Prefix Setting Non-Symbology Specific Suffixes Entering Programming ModeSET SET Suffix Setting a Single Character Prefix or Suffix Setting Prefix and/or Suffix Characters ONE Character only Ascii Character Set Symbology-Specific Label I.D Setting Symbology-Specific Label Identifiers Label I.DIndustry Standard Label Identifiers all are prefixes Setting Symbology Specific Label Identifiers Label I.D Label I.D. Symbology Selection EAN-13 W/2 Digit ADD- on EAN-13 W/5 Digit ADD- onEAN-13 W/C128 ADD- on ODE How to Set Single Character Label I.D This example 8 equals 38hex Disabling Label I.D. for a Specific Symbology Symbology Specific Label Identifiers Characters END Symbologies Symbology Options Overview Universal Symbology Selection Enable All Symbologies Disable All Symbologies1Standard 2 of 5 must be enabled before Iata can be enabled Symbology Selection SET Enable UPC/EAN Disable UPC/EAN Enable Code Disable Code Enable IATA3 Disable Iata Enable Codabar Disable Codabar Enable Code Disable Code Enable MSI/PLESSEY Disable MSI/PLESSEY UPC/EAN Options UPC/EAN Expansion Dont Expand EXPAND1Dont Expand END Optional Required Disabled END UPC/EAN Add-OnsC128 and Custom Add-Ons Price/Weight Check Digit Enable 4 Digit Check Enable 5 Digit CheckUPC Data Format Settings Send Check Digit Send NSD1 Dont Send NSD1 Send Check DIGIT2Send NSD2 Dont Send NSD2 END EAN Data Format Settings Code 39 Options Dont Compute Dont Transmit Enable Disable END Code Setting Lengths END AIM Symbology ID Prefix Code 128 Options Interleaved 2 Interleaved 2 of 5 Label Lengths Check Digit and Variable Length Label Selections Setting Interleaved 2 of 5 Fixed and Minimum Label Lengths Setting Fixed LengthsSetting Minimum Label Length Set Fixed SET First Fixed Length Standard 2 Standard 2 of 5 Label Lengths Check Digit and Variable Length Label Selections Setting Standard 2 of 5 Fixed and Minimum Label Lengths Standard 2 of 5 Fixed and Minimum Label Lengths 5 Fixed Abel Lengths Tandard Minimum Codabar Options Codabar Check Digit & Variable Length Codabar Start/Stop Character Format = abcd/abcd END Enable Fixed Codabar Fixed Length Codabar SET Fixed Lengths MSI/Plessey Check Digit ONE Check Digit TWO Check Digits END MSI/Plessey Fixed Length MSI/PLESSEY SET Fixed Lengths General Features Good Read Beeper Settings OFF Read Verification Universal Read Verification Read Verification by Symbology Verify UPC-A Verify UPC-E Verify EAN-8 Verify EAN-13Verify Code Verify Interleaved 2 Low Power Mode Disable LOW Power Idle Debug Mode AutoSense Stand Mode Host Programming Creating MultiFunction LabelsNeed More Information? Appendix B Sample Bar Codes UPC-E QuickScan 6000/6000 Plus Default Wand Keyboard Symbology RS-232 I/F Code 128 Options Transmit Don’t Transmit Codabar Options ABCD/ABCD Page Australia