Read Verification by Symbology | Datalogic Scanning 6000 PLUS

Read Verification by Symbology

To set the minimum read requirement for a desired symbology:

1. Scan the SET label.

2. Scan one symbology label below to select the symbology to be verified.

3. Scan the label on the following page representing the amount of times you wish a bar code label of that symbology type to be read before transmission to the host.

4. Repeat steps one through three above until read verification has been selected for all symbologies you desire to be verified.

5. Scan the END label.

SET

READ VERIFICATION SYMBOLOGY TYPE

----------------------------------------------

VERIFY UPC-A -------------------

VERIFY UPC-E -------------------

VERIFY EAN-8 --------------------

VERIFY EAN-13 ------------------

VERIFY INSTORE LABEL1 --------------------

VERIFY CODE 39 ------------------

1Instore labels are UPC-A bar codes with a number system character of 2 or 4, and EAN-8 and EAN-13 bar codes with a Flag 1 character of 2.

Programming Guide

83

Image 87

Datalogic Scanning 6000 PLUS manual Read Verification by Symbology, Verify UPC-A Verify UPC-E Verify EAN-8 Verify EAN-13

Contents

QuickScan 6000/6000 Plus Datalogic Scanning, Inc Contents Symbologies Additional InformationSample Bar Codes Integrating Peripherals With Host Systems Understanding the Basics Changing Interfaces HardwareSoftware Wand Emulation Keyboard Wedge RS-232 Customizing Your Scanner Operation What Is Programming Mode? How To Program Using Bar CodesProgramming Overview Programming Session Scanner Response When In Programming Mode If You Make a Mistake Return to Factory Settings Where To Go From Here END IBM 4683/84 4693/94 Port 5B SettingsIBM 4683/84 4693/94 Port 5B Interface Selection Send AS Code Dont Send AS Code IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E I/F Selection IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E Settings IBM 4682/92 Port E Interface Selection IBM 4682/92 Port E Settings Datalogic OCIA1 Interface Selection NCR Ocia Nine Bit long format Interface SelectionSNI Ocia Interface Selection Ocia Options Enable Disable END Wand Emulation Settings Wand Emulation Interface SelectionTransmit in C39 Transmit PRE-NOISE LOW High RS-232 Interface Selection SNI RS-232 Interface SelectionRS-232 Communication Parameters Data Format Table Baud Rate None Even ODD Mark Space ONE TWO Seven Bits Eight Bits END Data Format Settings Handshaking Hardware Control SET Enable XON/ Xoff Disable XON/XOFF END These features available for QuickScan 6000 Plus only Disable ACK/NAK Intercharacter Delay = 90 Milliseconds = 100 Milliseconds END Keyboard Wedge Communication Parameters PC Keyboard Wedge Interface Selection T YPE PC Keyboard Wedge Connect to a Laptop/No Keyboard Attached Keyboard Attached Enable Disable END SET Caps Lock OFF Caps Lock on Caps Lock QuickScan 6000 Plus only Country Mode QuickScan 6000 Plus only Spain Sweden Switzerland Japanese 106-KEY END Country Mode QuickScan 6000 Plus only Intercharacter Delay Intercharacter Delay Prefix & Suffix RS-232 and Keyboard Wedge Interfaces Only Programming Guide Non-Symbology Specific Items Setting Non-Symbology Specific PrefixesSET SET Prefix Setting Non-Symbology Specific Suffixes Entering Programming ModeSET SET Suffix Setting Prefix and/or Suffix Characters Setting a Single Character Prefix or Suffix ONE Character only Ascii Character Set Symbology-Specific Label I.D Setting Symbology-Specific Label Identifiers Label I.DIndustry Standard Label Identifiers all are prefixes Setting Symbology Specific Label Identifiers Label I.D Label I.D. Symbology Selection ODE EAN-13 W/2 Digit ADD- onEAN-13 W/5 Digit ADD- on EAN-13 W/C128 ADD- on This example 8 equals 38hex How to Set Single Character Label I.D Symbology Specific Label Identifiers Characters Disabling Label I.D. for a Specific Symbology END Symbologies Symbology Options Overview Universal Symbology Selection Enable All Symbologies Disable All Symbologies1Standard 2 of 5 must be enabled before Iata can be enabled SET Enable UPC/EAN Disable UPC/EAN Enable Code Disable Code Symbology Selection Enable IATA3 Disable Iata Enable MSI/PLESSEY Disable MSI/PLESSEY Enable Codabar Disable Codabar Enable Code Disable Code UPC/EAN Options UPC/EAN Expansion Dont Expand EXPAND1Dont Expand END Optional Required Disabled END UPC/EAN Add-OnsC128 and Custom Add-Ons Price/Weight Check Digit Enable 4 Digit Check Enable 5 Digit CheckUPC Data Format Settings Send Check Digit Send NSD1 Dont Send NSD1 Send Check DIGIT2Send NSD2 Dont Send NSD2 END EAN Data Format Settings Code 39 Options Code Dont Compute Dont Transmit Enable Disable END Setting Lengths END Code 128 Options AIM Symbology ID Prefix Interleaved 2 of 5 Label Lengths Interleaved 2 Check Digit and Variable Length Label Selections Set Fixed Setting Interleaved 2 of 5 Fixed and Minimum Label LengthsSetting Fixed Lengths Setting Minimum Label Length SET First Fixed Length Standard 2 of 5 Label Lengths Standard 2 Check Digit and Variable Length Label Selections Setting Standard 2 of 5 Fixed and Minimum Label Lengths Standard 2 of 5 Fixed and Minimum Label Lengths 5 Fixed Abel Lengths Tandard Minimum Codabar Options Codabar Check Digit & Variable Length Format = abcd/abcd END Codabar Start/Stop Character Codabar Fixed Length Enable Fixed Codabar SET Fixed Lengths ONE Check Digit TWO Check Digits END MSI/Plessey Check Digit MSI/Plessey Fixed Length MSI/PLESSEY SET Fixed Lengths Good Read Beeper Settings General Features OFF Universal Read Verification Read Verification Read Verification by Symbology Verify UPC-A Verify UPC-E Verify EAN-8 Verify EAN-13Verify Code Verify Interleaved 2 Disable LOW Power Idle Low Power Mode AutoSense Stand Mode Debug Mode Host Programming Creating MultiFunction LabelsNeed More Information? Appendix B Sample Bar Codes UPC-E QuickScan 6000/6000 Plus Default Wand Keyboard Symbology RS-232 I/F Code 128 Options Transmit Don’t Transmit Codabar Options ABCD/ABCD Page Australia