Disable ACK/NAK | Datalogic Scanning 6000 PLUS manual

RS-232 ACK/NAK Options (QuickScan 6000 Plus ONLY)

Several ACK/NAK parameters can be set for your QuickScan 6000 Plus scanner. Contact your Datalogic dealer if the specific ACK/NAK option you wish to set is not included in this section.

Options for RS-232 ACK/NAK are:

•Disable ACK/NAK

•Enable ACK/NAK for bar code transmission

•Enable ACK/NAK for host command acknowledge

•Enable ACK/NAK for bar code transmission and host command acknowledge.

(These features available for QuickScan 6000 Plus ONLY)

SET ----------------------------------------------

ACK/NAK ENABLE

DISABLE ACK/NAK -------------------

FOR BAR CODE TRANSMISSION --------

FOR HOST COMMAND ACKNOWLEDGE --

FOR BAR CODE TRANSMISSION --------

AND HOST COMMAND ACKNOWLEDGE

END ----------------------------------------------

Programming Guide

21

Image 25

Datalogic Scanning 6000 PLUS manual Disable ACK/NAK, These features available for QuickScan 6000 Plus only

Contents

QuickScan 6000/6000 Plus Datalogic Scanning, Inc Contents Additional Information SymbologiesSample Bar Codes Integrating Peripherals With Host Systems Understanding the Basics Hardware Changing InterfacesSoftware Wand Emulation Keyboard Wedge RS-232 Customizing Your Scanner Operation How To Program Using Bar Codes What Is Programming Mode?Programming Overview Programming Session Scanner Response When In Programming Mode If You Make a Mistake Return to Factory Settings Where To Go From Here IBM 4683/84 4693/94 Port 5B Interface Selection IBM 4683/84 4693/94 Port 5B SettingsSend AS Code Dont Send AS Code END IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E I/F Selection IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E Settings IBM 4682/92 Port E Interface Selection IBM 4682/92 Port E Settings NCR Ocia Nine Bit long format Interface Selection Datalogic OCIA1 Interface SelectionSNI Ocia Interface Selection Ocia Options Enable Disable END Wand Emulation Interface Selection Wand Emulation SettingsTransmit in C39 Transmit PRE-NOISE LOW High SNI RS-232 Interface Selection RS-232 Interface SelectionRS-232 Communication Parameters Data Format Table Baud Rate None Even ODD Mark Space ONE TWO Seven Bits Eight Bits END Data Format Settings Handshaking Hardware Control SET Enable XON/ Xoff Disable XON/XOFF END These features available for QuickScan 6000 Plus only Disable ACK/NAK Intercharacter Delay = 90 Milliseconds = 100 Milliseconds END Keyboard Wedge Communication Parameters PC Keyboard Wedge Interface Selection T YPE PC Keyboard Wedge Connect to a Laptop/No Keyboard Attached Keyboard Attached Enable Disable END SET Caps Lock OFF Caps Lock on Caps Lock QuickScan 6000 Plus only Country Mode QuickScan 6000 Plus only Spain Sweden Switzerland Japanese 106-KEY END Country Mode QuickScan 6000 Plus only Intercharacter Delay Intercharacter Delay Prefix & Suffix RS-232 and Keyboard Wedge Interfaces Only Programming Guide Setting Non-Symbology Specific Prefixes Non-Symbology Specific ItemsSET SET Prefix Entering Programming Mode Setting Non-Symbology Specific SuffixesSET SET Suffix Setting Prefix and/or Suffix Characters Setting a Single Character Prefix or Suffix ONE Character only Ascii Character Set Setting Symbology-Specific Label Identifiers Label I.D Symbology-Specific Label I.DIndustry Standard Label Identifiers all are prefixes Setting Symbology Specific Label Identifiers Label I.D Label I.D. Symbology Selection EAN-13 W/5 Digit ADD- on EAN-13 W/2 Digit ADD- onEAN-13 W/C128 ADD- on ODE This example 8 equals 38hex How to Set Single Character Label I.D Symbology Specific Label Identifiers Characters Disabling Label I.D. for a Specific Symbology END Symbologies Symbology Options Overview Enable All Symbologies Disable All Symbologies1 Universal Symbology SelectionStandard 2 of 5 must be enabled before Iata can be enabled SET Enable UPC/EAN Disable UPC/EAN Enable Code Disable Code Symbology Selection Enable IATA3 Disable Iata Enable MSI/PLESSEY Disable MSI/PLESSEY Enable Codabar Disable Codabar Enable Code Disable Code UPC/EAN Options Dont Expand EXPAND1 UPC/EAN ExpansionDont Expand END UPC/EAN Add-Ons Optional Required Disabled ENDC128 and Custom Add-Ons Enable 4 Digit Check Enable 5 Digit Check Price/Weight Check DigitUPC Data Format Settings Send NSD1 Dont Send NSD1 Send Check DIGIT2 Send Check DigitSend NSD2 Dont Send NSD2 END EAN Data Format Settings Code 39 Options Code Dont Compute Dont Transmit Enable Disable END Setting Lengths END Code 128 Options AIM Symbology ID Prefix Interleaved 2 of 5 Label Lengths Interleaved 2 Check Digit and Variable Length Label Selections Setting Fixed Lengths Setting Interleaved 2 of 5 Fixed and Minimum Label LengthsSetting Minimum Label Length Set Fixed SET First Fixed Length Standard 2 of 5 Label Lengths Standard 2 Check Digit and Variable Length Label Selections Setting Standard 2 of 5 Fixed and Minimum Label Lengths Standard 2 of 5 Fixed and Minimum Label Lengths 5 Fixed Abel Lengths Tandard Minimum Codabar Options Codabar Check Digit & Variable Length Format = abcd/abcd END Codabar Start/Stop Character Codabar Fixed Length Enable Fixed Codabar SET Fixed Lengths ONE Check Digit TWO Check Digits END MSI/Plessey Check Digit MSI/Plessey Fixed Length MSI/PLESSEY SET Fixed Lengths Good Read Beeper Settings General Features OFF Universal Read Verification Read Verification Verify UPC-A Verify UPC-E Verify EAN-8 Verify EAN-13 Read Verification by SymbologyVerify Code Verify Interleaved 2 Disable LOW Power Idle Low Power Mode AutoSense Stand Mode Debug Mode Creating MultiFunction Labels Host ProgrammingNeed More Information? Appendix B Sample Bar Codes UPC-E QuickScan 6000/6000 Plus Default Wand Keyboard Symbology RS-232 I/F Code 128 Options Transmit Don’t Transmit Codabar Options ABCD/ABCD Page Australia