P9+, Self cut-out | Delta DO 9704 instruction

KEY	SIMBOLS LIT BESIDES
		THE NUMBERS
	P9+	= enable/disable
		self cut-out

ENGLISH

FUNCTION

DESCRIPTION

- P9 -

When ENTER is pressed with P9 on the display, the instrument enters the program which enables or di ables the self cut-out func- tion when it is in storage mode and with a set storage interval higher than or equal to 1 minute.

The sand tkeys are used to select the value 00 or 01.

00 With a set storage interval lower than 1 minute, the instrument does not switch off automatically; it always remains lit.

When the ON/OFF key is pressed, storage stops and the instrument switches off.

00 With a set storage interval higher than 1 minute, the display switches off automati- cally after about 8 minutes. At each set storage interval there is a beep and the display swit- ches on for a few seconds..

The display can be switched on or off by pressing the ON/OFF key. The instrument keeps on storing if you keep it switched on. The display swit- ches off automatically after about 8 minutes.

To stop storage, press the ON/OFF key (if the instrument is off). Press the ENTER key.

01 With a set storage interval lower than 1 minute, the instrument does not switch off

80

Image 16

Delta DO 9704 manual P9+, Self cut-out

Contents

Instructions Manual Page Pressure and Temperature DATA-LOGGER English Introduction Keyboard KEY Numbers Function Description Simbols LIT BesidesNumbers REL Tom of the display Simbols LIT Besides Function Numbers DescriptionSerial Output P0+ Press the Prog key to move on to step P1300 Baud 600 Baud P1+ = data dump P1+ StorageHours minutes Seconds This parameter is used for the fol- lowing two functions Function P3+ P4+ = set year P5+ = set month P6+ = set day P7+ = set hours P8+ = set minutes P9+ Self cut-out P10+ To stop storage, press the Enter keyP10 Complete printing Reduced printing P11+ P11Data Call + Start-Stop Operating mode When this operativeKEY Simbols LIT Besides Ches itself off again If the battery symbol does not fla Simbols LIT Besides Function Numbers Description Enter More than 30,000 acquisitions Restart itAfter having taken note HOW to Measure Probe Connection Various operations Temperature Measurement Method of Using the Instrument and Warnings Instrument Signals and Malfunctions ErrFUL LOU LOW Battery Warning and Battery Replacement Storage of the Instrument Serial Interface RS 232C Command Type Reply Parity None Bit Stop bit Protocol Xon/XoffType of terminal Dumping data from the memory Memory clear Diagram do Printer Example of a Report Printed by the Instrument English Hardware connection Software connection with Windows OK to confirm the setting one click Mark local Echo one click 100 101 Switch on the measuring instrument 102 OK to confirm Cancel in the next window 103 Parity None 104 105 106 107 108 109 To end receiving data from an instrument Select END from the pull-down sub-menu one clickTo quit running the Hyper Terminal 110 Calibrating the Instrument do Vdc=465.5 Flow Rate Measurements Connection of Probes to the Pressure Gauge Data Logger do Probe connection diagram Instrument do113 SEL R 100 105 110 115Turbine probe for measuring flow rate Between 4 Classification of Pressure Measurements Gauge Conversion Factors and Tables Psi = Pa Psi = kPa= 3,386 x 103 Pa = 2,491 x 102 Pa 118 Instrument Technical Data Connector DIN 45326 8-poleWeight / dimensions 320 gr. / 215x73x38 mm Minimum, Mean, Relative, A-B differential 120 121 Order Codes Guarantee Examples of USE of the Keyboard Serial lineDisplay blocked 124 Pressing Data Call repeatedly gives 125 Instrument programming Sets year Sets daySets hour 127 Enables self cut-out + Normal operatingDate and time Data printing is reduced 128 Activation or disactivation of the serial output Activation or disactivation of the Record functionFunction Serial output active Activation and disactivation of the storage function 130 Index 131 132 Safety EN61000-4-2, EN61010-1 level