Audio Delay

Default settings are underlined.

While viewing video, manually adjust the time to delay audio output.

Setting details

0ms – 200ms

•This item can be set within the range of 0 to 100 ms when “Auto Lip Sync” (vpage 120) is set to “On” and when a TV compatible with Auto Lip Sync is connected.

•Store “Audio Delay” for each input source.

•Audio Delay for game mode can be set when “Video Mode” (vpage 121) is set to “Auto” or “Game”.

Volume

Default settings are underlined.

 

 

Set the MAIN ZONE (room where the unit is located) volume setting.

Setting items

Setting details

Scale

0 – 98 : Display in the range 0 (Min) to 98.

Set how volume is

–79.5dB – 18.0dB : Display ---dB (Min), in the range –79.5 dB to 18.0 dB.

displayed.

 

 

• The “Scale” setting is applied also to the “Limit” and “Power On Level”

 

display method.

 

• The “Scale” setting applies to all zones.

Limit

Off : Do not set a maximum volume.

Make a setting for

60 (–20dB) /70 (–10dB) /80 (0dB)

maximum volume.

 

Power On Level

Last : Use the memorized setting from the last session.

Define the volume setting

Mute : Always use the muting on condition when power is turned on.

that is active when the

1 – 98 (–79dB – 18dB) : The volume is adjusted to the set level.

power is turned on.

 

Mute Level

Full : The sound is muted entirely.

Set the amount of

–40dB : The sound is attenuated by 40 dB down.

attenuation when muting

–20dB : The sound is attenuated by 20 dB down.

is on.

 

 

Audio

Audyssey

Default settings are underlined.

Set Audyssey MultEQ® XT, Audyssey Dynamic EQ® and Audyssey Dynamic Volume®. These can be selected after Audyssey® Setup has been performed. For additional information on Audyssey technology, please see page 168.

NOTE

•If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup,

you may not be able to select Dynamic EQ/Dynamic Volume.

In this case, either perform Audyssey® Setup over again or perform “Restore...” (vpage 35) to return to the settings after Audyssey® Setup was run.

•When HD Audio for which the sampling frequency exceeds 96 kHz is played back, the “Audyssey” cannot be set.

Setting items

 

Setting details

 

 

 

 

MultEQ®XT

Audyssey : Optimize the frequency response of all speakers.

MultEQ® XT compensates

Audyssey Byp. L/R : Optimize frequency response of speakers except

for both time and

front L and R speakers.

 

 

 

frequency characteristics

Audyssey Flat : Optimize frequency response of all speakers to flat

of the listening area based

response.

 

 

 

on Audyssey® Setup

Graphic EQ : Apply frequency response

set with

“Graphic EQ”

measurement results.

(vpage 118).

 

 

 

Selection is done from three

Off : Turn “MultEQ® XT” equalizer off.

 

 

types of compensation

 

 

 

 

curves. We recommend the

• “Audyssey”, “Audyssey

Byp. L/R” and

“Audyssey

Flat” can be

“Audyssey” setting.

selected after Audyssey® Setup has been performed. “Audyssey”

MultEQ® XT is the

prerequisite function for

is automatically selected

after performing

Audyssey®

Setup. When

“Audyssey”, “Audyssey

Byp. L/R” or “Audyssey Flat” is selected,

Dynamic EQ and Dynamic

illuminates.

 

 

 

Volume.

 

 

 

• After running Audyssey® Setup, if the Speaker Configuration, Distance,

 

 

Channel Level, and Crossover Frequency have changed without

 

increasing the number of speakers measured, only

illuminates.

NOTE

When using headphones, “MultEQ® XT” is automatically set to “Off”.

“MultEQ® XT”, “Dynamic EQ” and “Dynamic Volume” settings are stored for each input source.

v See overleaf

version Basic

version Advanced

Informations

DVD

116