Symptom | Cause/Solution | Page |
No sound is | • Check the subwoofer connections. | 85,86,87,88, |
produced from |
| 89, 90, 91 |
subwoofer. | • Turn on the subwoofer’s power. | – |
| • Set “Speaker Config.” – “Subwoofer” on the menu to “Yes”. | 130 |
| • If “Front” and “Center” for “Speaker Config.” are set to “Large”, | 130, 131 |
| and “Subwoofer Mode” is set to “LFE”, no sound may be output |
|
| from the subwoofers, depending on the input signal or selected |
|
| sound mode. |
|
DTS sound is not | • Set “Decode Mode” on the menu to “Auto” or “DTS”. | 127 |
output. |
|
|
Dolby TrueHD, DTS- | • Make HDMI connections. | 11 |
HD, Dolby Digital |
|
|
Plus audio is not |
|
|
output. |
|
|
Dolby PLg mode or | • Check that “Speaker Config.” – “Center” or “Surround” is set to | 130 |
DTS NEO:6 mode | other than “None”. If the speaker system is 2.0/2.1ch, this sound |
|
cannot be selected. | mode cannot be selected. |
|
| • When headphones are used, Dolby PLg or DTS NEO:6 cannot be | – |
| selected. |
|
Audyssey MultEQ® | • Switch the sound mode to other than “DIRECT” or “PURE | 75 |
XT, Audyssey | DIRECT”. |
|
Dynamic EQ® and | • When headphones are used, Audyssey MultEQ® XT, Audyssey | – |
Audyssey Dynamic | Dynamic EQ® and Audyssey Dynamic Volume® cannot be |
|
Volume® cannot be | selected. |
|
selected. |
|
|
Audyssey DSX® | • Check that “Speaker Config.” – “Front Height” or “Front Wide” is | 131 |
cannot be selected. | set to other than “None”. |
|
| • Check that “Speaker Config.” – “Center” is set to other than | 130 |
| “None”. |
|
| • Switch the sound mode to DOLBY listening mode or DTS listening | 75 |
| mode. |
|
| • When headphones are used, Audyssey DSX® cannot be selected. | – |
Audyssey Dynamic | • Run Audyssey® Setup. | 29, 92 |
EQ® and Audyssey |
|
|
Dynamic Volume® |
|
|
cannot be selected. |
|
|
Symptom | Cause/Solution | Page |
“Restorer” cannot | • Check that an analog signal or PCM signal (Sample Rate=44.1/48 | 115 |
be selected. | kHz) is input. For playback of multichannel signals such as Dolby |
|
| Digital or DTS surround, “Restorer” cannot be used. |
|
| • Switch the sound mode to other than “DIRECT” or “PURE | 75 |
| DIRECT”. |
|
When the HDMI | • The HDMI audio signals selected for ZONE2 are only output to the | – |
ZONE2 function is | HDMI ZONE2 OUT connector. (The HDMI audio signals selected |
|
used, in spite of | for ZONE2 are not output from the speaker of the TV in ZONE2 |
|
“Assign Mode” | that is connected to this unit.) |
|
being set to |
|
|
“ZONE2”, no audio |
|
|
is output from the |
|
|
speakers connected |
|
|
with this unit. |
|
|
GHD RadioH |
|
|
Symptom | Cause/Solution | Page |
Reception fails, or | • Change the antenna orientation or position. | 24 |
there is a lot of noise | • Separate the AM loop antenna from the unit. | 24 |
or distortion. | • Use an FM outdoor antenna. | 24 |
| • Separate the antenna from other connection cables. | 24 |
version Basic
version Advanced
Informations
DVD | 173 |