Signal

 

 

 

transmission

[

 

AMP]

indicator

 

[MODE SELECTOR]

[

TU]

[

NET/DTU]

[ iPod]

[NUMBER]

[RC SETUP]

Setting the Remote ID

When using multiple DENON AV receivers in the same room, make this setting so that only the desired AV receiver operates.

1Press [AMP] to set the main remote control unit to the AMP mode.

2Press and hold in [RC SETUP] for at least 3 seconds. The signal transmission indicator flashes twice.

3Refer to the table at the right, and use [NUMBER] to input the 5-digit number corresponding to the remote

ID to be changed.

The signal transmission indicator flashes twice.

4Press [TU], [iPod] or [NET/DTU] to select the mode to be set.

5Repeat steps 2 to 4 to set the remote IDs for all modes.

MODE

 

TUNER

 

NET/DTU

SELECTOR

 

 

 

 

 

 

 

 

AMP

DEVICE1

DEVICE2

iPod

DEVICE1

 

(MAIN)

(Net

 

(Analog

(XM)

 

 

 

 

Audio /

 

 

TUNER)

 

 

Remote ID

 

 

 

USB)

 

 

 

 

 

 

 

 

 

 

1

81001

52863

52864

72815

62865

(Default)

 

 

 

 

 

2

82001

52795

52812

72816

62837

3

83001

52800

52813

72817

62838

4

84001

52805

52814

72818

62839

 

 

 

 

 

 

NOTE

•When changing a setting, be sure to set the same remote ID as the AVR-3808CI’s (vpage 35).

•When changing the AMP mode’s remote ID, also change the “TUNER”, “iPod” and “NET/DTU” remote ID at the same time.

•Set the remote ID of an analog tuner for “TUNER” – “DEVICE1”, the XM remote ID for “DEVICE2”.

Learning Function

If your AV devices are of a brand other than DENON or if they cannot be operated with the preset memory function, their remote control signals can be transfered to stored in the AVR-3808CI’s main remote control unit.

1Press [MODE SELECTOR] for the device you want to set.

2Press and hold in [RC SETUP] for at least 3 seconds. The signal transmission indicator flashes twice.

3Press [9], [7] and [5], in that order.

The signal transmission indicator flashes twice and the learning mode is set.

4Press the button to be set.

The main remote control unit’s display turns off.

bIf a button that cannot be learned is pressed, the signal transmission indicator lights but the signal is not learned.

5Point the main remote control units directly at each other and press and hold the button on the other

device’s remote control unit that you want to learn.

Once learning is completed normally, the display lights and the signal transmission indicator flashes twice.

Other device’s remote control unit

AVR-3808CI’s main remote

control unit (RC-1068)

b If you want to learn other buttons, repeat steps 4 and 5. b The mode can be switched by pressing [MODE SELECTOR].

b The signal transmission indicator lights once for a long time if learning was not possible

6Press and hold in [RC SETUP] for at least 3 seconds. The signal transmission indicator flashes twice and the setting is completed.

•With some remote control units, the signals cannot be learned or the device will not operate properly even when the signals have been learned. In this case, use the device’s own remote control unit.

•Learned buttons have priority over the preset memory. If you no longer need the learned setting, reset the learning function (vpage 64).

NOTE

•[HOME] cannot be learned.

•Do not learn any remote control signals at [RC SETUP].

•The AMP, ZONE2, ZONE3, ZONE4 and SYSTEM CALL modes cannot be learned.

Troubleshooting Information Zone-Multi Control Remote Playback Setup Connections Started Getting

62