DESCRIPTION OF EVENT CODES

Event Code

Description

Action

 

Base: NO AC

No power to Base Unit

Check power supply

 

Base: POWER RESTORED

Base Unit power restored

NA

 

DEV x txt: NO AC

No power to device

Check power supply

 

DEV x txt: POWER RESTORED

Device power restored

NA

 

DEV x txt: LOW BATT

Device battery low

Change battery,

 

 

 

reset device

 

DEV x txt: LOW BATT CLR

Device battery restored

NA

 

BASE LOW BATT

Battery has dropped below

Plug in power supply

 

 

the voltage limit

to recharge battery

 

BASE LOW BATT CLR

Base Unit battery has

NA

 

 

been restored

 

 

DEV x txt: SIGNAL WEAK

Transmission signal from

Check for

 

 

device is weak

interference move

 

 

 

device location

 

DEV x txt: SIGNAL GOOD

Transmission signal from

NA

 

 

device now OK

 

 

DEV x txt: TAMPER

Device has been opened

Close device or

 

 

or damaged

or replace if damaged

 

DEV x txt: NO CHECK IN

Device check-in messages

Check for interference

 

 

have not been received

move device location

 

DEV x txt: NO CHECK IN CLR

Device check-in message

NA

 

 

has been received

 

 

DEV x txt: RESET

Device has been reset

NA

 

DEV x txt: REGISTERED

Device has been registered

NA

 

DEV x txt: REMOVED

Device has been

NA

 

 

unregistered and removed

 

 

 

from programming

 

 

Base: BATTERY FAULT

System battery is

Needs to be repaired at

 

 

defective

DEWALT authorized

 

 

 

service center

 

Base: BATTERY FAULT CLR

Base Unit battery has

NA

 

 

been restored

 

 

Base Motion: ALARM

Base Unit motion

Check for intrusion at

 

 

sensor tripped

Base Unit

 

Base Motion: ALARM CLR

Base Unit motion

NA

 

 

sensor alarm cleared

 

 

Base Vibration: ALARM

Base Unit vibration

Check for intrusion at

 

 

sensor tripped

Base Unit

 

Base Vibration: ALARM CLR

Base Unit vibration sensor

NA

 

 

alarm cleared

 

 

Cell Radio: SHUTDOWN

Cellular radio has been

See Troubleshooting;

 

 

shut down

call customer service

 

Cell Radio: ACTIVATED

Cellular radio has been

NA

 

 

reactivated

 

 

USER x txt: ARMED or

User x or Key Chain

NA

 

DEV x txt: ARMED (keychain) or

Remote x has armed

 

 

ARMED (code)

the system

 

 

USER x txt: DISARMED or

User x or Key Chain

NA

 

DEV x txt: DISARMED (keychain) or

Remote x has disarmed

 

 

DISARMED (code)

the system

 

DESCRIPTION OF EVENT CODES

Event Code

Description

Action

 

 

 

USER x txt: FORCED ARM or

User x or Key Chain

Check for faults; resolve

 

 

DEV x txt: FORCED ARM (keychain)

Remote x has armed

issue, clear fault and

 

 

or FORCED ARM (code)

the system over a fault

then re-arm

 

 

 

Base: AUTOARM

System has been

NA

 

 

 

automatically armed

 

 

 

 

 

Base: FORCED AUTOARM

System has been

Check for faults; resolve

 

 

 

automatically armed

issue, clear fault and

 

 

 

over a fault

then re-arm

 

 

 

Base: CALL SUCCESS

A call has been made

NA

 

 

 

to the monitoring service

 

 

 

 

 

Base: CALL FAIL

A call to the monitoring

Call customer service to

 

 

 

service failed

test system for issues

 

 

 

Base Siren: ENABLED or

Base Unit siren or strobe

NA

 

 

Base Strobe: ENABLED

has been enabled

 

 

 

 

 

Base Siren: DISABLED or

Base Unit siren or strobe

NA

 

 

Base Strobe: DISABLED

has been disabled

 

 

 

 

 

ENTER MASTER MODE

Master user entered

NA

 

 

 

master mode

 

 

 

 

 

MASTER MODE TIMEOUT

Master user allowed

NA

 

 

 

system to time out

 

 

 

 

 

EXIT MASTER MODE

Master user exited

NA

 

 

 

master mode

 

 

 

 

 

USER x: ADDED

User x has been added

NA

 

 

 

to the system

 

 

 

 

 

USER x: REMOVED

User x has been removed

NA

 

 

 

from the system

 

 

 

 

 

TIME/DATE CHANGED

Master user changed

NA

 

 

 

time and/or date

 

 

 

 

 

FAULTS CLEARED

Master user cleared

NA

 

 

 

faults

 

 

 

 

 

DEV x txt: RECEIVER FAULT

2-way transmission of

Call customer service to

 

 

 

device is lost

test system for issues

 

 

 

DEV x txt: RECEIVER FAULT CLR

2-way transmission of

NA

Appendix

 

 

device is restored

 

 

 

 

 

 

 

 

 

 

DEV x txt: ALARM

Dev x unsecured

Check dev x

 

 

 

(only when armed)

 

 

 

 

 

DEV x txt: ALARM CLR

Dev x secured

NA

 

 

 

(only when armed)

 

 

 

 

 

CELL RADIO: NO CHECK IN

Cell radio fault

NA

 

 

 

CELL RADIO: NO CHECK IN CLR

Cell radio cleared

NA

 

 

 

BASE NC: NO CHECK IN

Network control fault

Fault will clear itself

 

 

 

(RF processor)

 

 

 

 

 

BASE NC: NO CHECK IN CLR

Network control cleared

NA

 

 

 

FORCED DISARM

Force disarm due to

NA

 

 

 

low battery

 

 

 

 

 

Base: PERIODIC TEST

Periodic call to

NA

 

 

 

monitoring service

 

 

 

 

 

Base: ALARM CLR

8-minute alarm

 

 

 

 

 

 

cycle complete

NA

 

 

24

Page 31
Image 31
DeWalt DS100, DS200 instruction manual Description of Event Codes, Event Code Description Action

DS100, DS200 specifications

DeWalt has long been recognized as a leader in the power tool industry, and its DS200 and DS100 models continue this tradition by offering innovative features and reliable performance. Both models are designed with contractors and DIY enthusiasts in mind, providing durability and efficiency in various applications.

The DeWalt DS200 is a dual-speed, heavy-duty job site radio designed to withstand the rigors of construction environments. It boasts an impressive 20V MAX lithium-ion battery compatibility, allowing for extended battery life and convenience on the job site. One of the main features of the DS200 is its Bluetooth connectivity, enabling users to stream music directly from their smartphones or tablets. This added functionality allows for a more enjoyable work environment, fostering motivation and focus.

The sound quality of the DS200 is exceptional, featuring high-performance speakers and a digital sound processing system. Its rugged exterior is designed to protect it against dust and moisture, making it highly suitable for outdoor use. The DS200 also features a built-in USB port, allowing users to charge their devices while on the go. Additionally, its integrated hooks and available carrying handle offer enhanced portability, enabling easy transportation from one job site to another.

On the other hand, the DeWalt DS100 is a more compact and lightweight option, perfect for those seeking a portable audio solution without compromising on sound quality. The DS100 also supports 20V MAX lithium-ion batteries, ensuring compatibility and extending battery runtime. With its integrated Bluetooth technology, users can easily connect their devices and enjoy crisp audio performance.

The DS100's design prioritizes convenience, featuring a durable carry strap and a compact size that allows it to fit comfortably in small spaces. Despite its smaller stature, the DS100 does not sacrifice sound quality, providing rich audio capable of filling a room.

Both models exemplify DeWalt's commitment to quality and innovation. With their robust designs and advanced technologies, the DS200 and DS100 cater to the needs of modern users, making them essential tools for both professional contractors and home improvement enthusiasts. Whether in the workshop or on the job site, these audio solutions enhance productivity and elevate the working experience.