Pull cables to the PoleVault switcher | Extron electronic VLM 2000

4.Pull cables to the PoleVault switcher.

a.Pull the cables from the receiver to the PoleVault switcher’s location.

b.Remove the base of the PMK Pole Mount Kit to access the switcher.

c.Run the cables down through the top of the pole and out through the access hole.

Ó Runpole.the cable(s) through the projector

5.Connect cables to the PoleVault switcher.

a.Disconnect the cable from the PoleVault switcher’s

5-poleRS-232 MLC/IR port, and disconnect the power cable from the switcher.

b.Connect the VoiceLift adapter to the PoleVault switcher as follows:

•Connect the adapter’s three-pole captive screw connector to the switcher’s three-pole Aux/Mix In port.

•Connect the adapter’s five-pole connector to the switcher’s RS-232 MLC/IR port.

c.Connect the Ethernet cable to the VoiceLift adapter’s RJ-45 jack.

d.Connect the MLC controller’s power/communication cable to the VoiceLift adapter’s five-pole captive screw connector.

e.Reconnect the power cable to the PoleVault switcher.

f.Reattach the bottom section of the PMK (containing the switcher) to the top section.

Â–Ú	Connect the adapter to the
	PoleVault switcher.

	3-pin Connector	5-pin Connector in
		RS-232 MLC-IR Port
	in Aux/Mix In Port

Ethernet Cable		MLC Pwr/RS232
		Cable in MLC Port
in RJ-45 Jack

ÙConnect the MLC cable to the adapter’s five-pole MLC connector.

VoiceLift Microphone Installation • Installation — Stage 2

2-13

Image 21

Extron electronic VLM 2000, VLM 1000 manual Pull cables to the PoleVault switcher, Connect cables to the PoleVault switcher

Contents

VoiceLift Microphone Safety Instructions English PrecautionsConsignes de Sécurité Français Sicherheitsanleitungen Deutsch VoiceLift Microphone Installation Introduction Overview VoiceLift Microphone installation and wiring overviewIntroduction Overview FCC Class B Notice VoiceLift Microphone Installation Introduction Planning Typical classroom installationIntroduction Planning Room layout Room configuration Example of a classroom installationRoom considerations  The room is larger than 40 by Introduction Planning, cont’d Introduction Inventory Overview InventoryIncluded items Items not included  Bolts for concrete structural ceilings where needed VoiceLift Microphone Installation Installation Overview Installation Overview Stage 3 Configure and Test the System Stage 1 Install the VLR 102 Receiver Drop ceilingJunction box Wall or other hard surface Installation Stage VoiceLift Microphone Installation Installation StageDrop ceiling Junction box Wall or other hard surface Mount the receiver housing to the ceiling tile Installing the Receiver in a Drop CeilingCut a hole in the ceiling tile Cut a hole in the ceiling tile CAttach a conduit to the back plate if desired Attach a conduit to the back plate if needed Install the junction box Installing the Receiver in a Junction BoxAttach the receiver housing to the junction box Attach a conduit to the junction box if needed Installing the Receiver in a Wall or Other Hard Surface Install a raceway if neededMark the mounting screw locations on the surface Mount the receiver housing to the surface If not using a racewayIf using a raceway Receiver dome Where it goes Connects to the PVS 204 SA PoleVault switcherVoiceLift Adapter Ethernet cable ÇConnect the Ethernet cable to Receiver Out RJ-45 jack Pull the cables to the receiver Connect the cables to the receiver Attach the receiver dome to the housing Align the arrows on the housing rim and the dome tab Attach the receiver dome to the housing Connect cables to the PoleVault switcher Pull cables to the PoleVault switcherPoleVault switcher Runpole.the cables through the projector Set up the microphone Configure the systemÏSet up the microphone Test the system Adjust the audio level Finish the installationVoiceLift Microphone Installation Installation Stage 3 Walk around the room to check for sound quality Insert the black wire into the Ground port Optional Installation Example Instant AlertConnect the receiver to the MLC 104 IP Plus Connect the communication cable to an MLC Digital I/O port Using Global Configurator, configure the MLC’s Configure the MLC 104 IP PlusPress and hold both Volume buttons Test the instant alert notification Specifications VLR 102 and VLR 102 SR VoiceLift Microphone Installation Reference InformationReference Information General Audio/acoustic and electrical Specifications VLP 102 VoiceLift Microphone Specifications VLC 102 Microphone Charging Station Stage 2 Connect the Receiver to the PoleVault System Configure the system. Set up the microphone Test the system.