Installation Overview | Extron electronic VLM 2000, VLM 1000

Installation — Overview

NFor operation and setup of other Extron PoleVault system components mentioned in this guide, refer to the appropriate user manual provided with each product.

This overview outlines the basic steps for installing the VLR 102 VoiceLift Receiver. Detailed descriptions with illustrations of these steps are provided in three sections, stages One through Three. If VLR 102 SR Secondary Receiver(s) are being used with your system, this installation procedure applies to them as well.

N

•Additional installation hardware is needed for this installation, and should be supplied by the installer. See

“Items not included,” in chapter 1, “Introduction,” for a list of items that you may need.

•Optional accessories may be desired for this installation. See “Optional items”, in chapter 1, “Introduction,” for a list of available accessories, or visit www.extron.com for details.

•Refer to local building standards and codes to verify that the installation will meet all the regulatory requirements.

•Observe all local and national building and safety codes, UL requirements, and ADA Accessibility Guidelines.

Mounting the VoiceLift receiver to a wall

Mounting the VoiceLift receiver in a drop ceiling.

Mounting the VoiceLift receiver in a junction box

The following pages contain instructions for installing the VLR 102 IR Receiver. Where possible, line drawings and photos from an actual installation are used to clarify some of the steps discussed in the text. Each image has a number

corresponding to the step that is being described (e.g., Ñ).

VoiceLift Microphone Installation • Installation — Overview

2-1

Image 9

Extron electronic VLM 2000, VLM 1000 manual VoiceLift Microphone Installation Installation Overview

Contents

VoiceLift Microphone Safety Instructions English PrecautionsConsignes de Sécurité Français Sicherheitsanleitungen Deutsch VoiceLift Microphone Installation Introduction Overview VoiceLift Microphone installation and wiring overviewIntroduction Overview FCC Class B Notice VoiceLift Microphone Installation Introduction Planning Typical classroom installationIntroduction Planning Room layout Room configuration Example of a classroom installationRoom considerations  The room is larger than 40 by Introduction Planning, cont’d Introduction Inventory Overview InventoryIncluded items Items not included  Bolts for concrete structural ceilings where needed VoiceLift Microphone Installation Installation Overview Installation Overview Stage 3 Configure and Test the System Stage 1 Install the VLR 102 Receiver Drop ceilingJunction box Wall or other hard surface Installation Stage VoiceLift Microphone Installation Installation StageDrop ceiling Junction box Wall or other hard surface Mount the receiver housing to the ceiling tile Installing the Receiver in a Drop CeilingCut a hole in the ceiling tile Cut a hole in the ceiling tile CAttach a conduit to the back plate if desired Attach a conduit to the back plate if needed Install the junction box Installing the Receiver in a Junction BoxAttach the receiver housing to the junction box Attach a conduit to the junction box if needed Installing the Receiver in a Wall or Other Hard Surface Install a raceway if neededMark the mounting screw locations on the surface Mount the receiver housing to the surface If not using a racewayIf using a raceway Receiver dome Where it goes Connects to the PVS 204 SA PoleVault switcherVoiceLift Adapter Ethernet cable ÇConnect the Ethernet cable to Receiver Out RJ-45 jack Pull the cables to the receiver Connect the cables to the receiver Attach the receiver dome to the housing Align the arrows on the housing rim and the dome tab Attach the receiver dome to the housing Connect cables to the PoleVault switcher Pull cables to the PoleVault switcherPoleVault switcher Runpole.the cables through the projector Set up the microphone Configure the systemÏSet up the microphone Test the system Adjust the audio level Finish the installationVoiceLift Microphone Installation Installation Stage 3 Walk around the room to check for sound quality Insert the black wire into the Ground port Optional Installation Example Instant AlertConnect the receiver to the MLC 104 IP Plus Connect the communication cable to an MLC Digital I/O port Using Global Configurator, configure the MLC’s Configure the MLC 104 IP PlusPress and hold both Volume buttons Test the instant alert notification Specifications VLR 102 and VLR 102 SR VoiceLift Microphone Installation Reference InformationReference Information General Audio/acoustic and electrical Specifications VLP 102 VoiceLift Microphone Specifications VLC 102 Microphone Charging Station Stage 2 Connect the Receiver to the PoleVault System Configure the system. Set up the microphone Test the system.