Extron electronic VLM 1000, VLM 2000 manual

Outline of installation steps

Stage 1 — Install the VLR 102 Receiver

Drop ceiling:

cCut a hole in the ceiling tile. (page 2-4)

cMount the receiver housing to the ceiling tile. (page 2-4)

cAttach a conduit to the back plate if needed. (page 2-5)

Junction box:

cInstall the junction box. (page 2-6)

cAttach the receiver housing to the junction box. (page 2-6)

cAttach a conduit to the junction box if needed. (page 2-6)

Wall or other hard surface:

cInstall a raceway if needed. (page 2-7)

cMark the mounting screw locations on the surface. (page 2-7)

cIf using a raceway, remove the appropriate knockout in the receiver housing. (page 2-7)

cMount the receiver housing to the surface. (page 2-8)

Stage 2 — Connect the Receiver to the PoleVault System

cPull the cables to the receiver. (page 2-10)

cConnect the cables to the receiver. (page 2-10)

cAttach the receiver dome to the housing. (page 2-11)

cPull cables to the PoleVault switcher. (page 2-13)

Stage 3 — Configure and Test the System

cConfigure the system. (page 2-14)

cSet up the microphone (page 2-14)

cTest the system. (page 2-14)

cComplete the installation. (page 2-15)

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500 +1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794 +1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040 +31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400 +65.6383.4664 FAX

Extron Japan

+81.3.3511.7655 +81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568 +86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800 +971.4.2991880 FAX

© 2009 Extron Electronics. All rights reserved.

Image 30

Extron electronic VLM 1000, VLM 2000 manual Stage 2 Connect the Receiver to the PoleVault System

Contents

VoiceLift Microphone Consignes de Sécurité Français PrecautionsSafety Instructions English Sicherheitsanleitungen Deutsch Introduction Overview VoiceLift Microphone installation and wiring overviewVoiceLift Microphone Installation Introduction Overview FCC Class B Notice Introduction Planning Typical classroom installationVoiceLift Microphone Installation Introduction Planning Room layout Room configuration Example of a classroom installationRoom considerations Introduction Planning, cont’d  The room is larger than 40 by Introduction Inventory Overview InventoryIncluded items  Bolts for concrete structural ceilings where needed Items not included Installation Overview VoiceLift Microphone Installation Installation Overview Junction box Stage 1 Install the VLR 102 Receiver Drop ceilingStage 3 Configure and Test the System Wall or other hard surface Installation Stage VoiceLift Microphone Installation Installation StageDrop ceiling Junction box Wall or other hard surface Cut a hole in the ceiling tile Installing the Receiver in a Drop CeilingMount the receiver housing to the ceiling tile Cut a hole in the ceiling tile Attach a conduit to the back plate if needed CAttach a conduit to the back plate if desired Attach the receiver housing to the junction box Installing the Receiver in a Junction BoxInstall the junction box Attach a conduit to the junction box if needed Installing the Receiver in a Wall or Other Hard Surface Install a raceway if neededMark the mounting screw locations on the surface Mount the receiver housing to the surface If not using a racewayIf using a raceway VoiceLift Adapter Where it goes Connects to the PVS 204 SA PoleVault switcherReceiver dome Ethernet cable Pull the cables to the receiver ÇConnect the Ethernet cable to Receiver Out RJ-45 jack Attach the receiver dome to the housing Connect the cables to the receiver Attach the receiver dome to the housing Align the arrows on the housing rim and the dome tab PoleVault switcher Pull cables to the PoleVault switcherConnect cables to the PoleVault switcher Runpole.the cables through the projector ÏSet up the microphone Configure the systemSet up the microphone Test the system VoiceLift Microphone Installation Installation Stage 3 Finish the installationAdjust the audio level Walk around the room to check for sound quality Connect the receiver to the MLC 104 IP Plus Optional Installation Example Instant AlertInsert the black wire into the Ground port Connect the communication cable to an MLC Digital I/O port Press and hold both Volume buttons Configure the MLC 104 IP PlusUsing Global Configurator, configure the MLC’s Test the instant alert notification Specifications VLR 102 and VLR 102 SR VoiceLift Microphone Installation Reference InformationReference Information General Specifications VLP 102 VoiceLift Microphone Audio/acoustic and electrical Specifications VLC 102 Microphone Charging Station Configure the system. Set up the microphone Test the system. Stage 2 Connect the Receiver to the PoleVault System