Lowering the Two Rear Rollers, Installation | Falcon U108610-07

On no account try and move the cooker while it is

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Moving the Cooker

On no account try and move the cooker while it is

nn

plugged into the electricity supply.

The cooker is very heavy, so take great care.

nn

We recommend that two people manoeuvre the cooker. Make sure that the oor covering is rmly xed, or removed, to prevent it being disturbed when moving the cooker around.

To help you, there are two levelling rollers at the back, and two screw-down levelling feet at the front.

Remove the polystyrene base pack. From the front, tilt the cooker backwards and remove the front half of the polystyrene base (Fig.7-3). Repeat from the back and remove the rear half of the polystyrene base.

Lowering the Two Rear Rollers

To adjust the height of the rear of the cooker, rst t a 13 mm spanner or socket wrench onto the hexagonal adjusting nut (Fig.7-4). Rotate the nut – clockwise to raise – counter- clockwise to lower.

Make 10 complete (360°) turns clockwise. Make sure you lower BOTH REAR ROLLERS.

	Completing the Move
	Unfold the rear edge of the cardboard base tray. Open the	ArtNo.010-0004 Moving the cooker
	grill door and right-hand oven door so that you can get a	ArtNo.010-0004 Moving the cooker
	grill door and right-hand oven door so that you can get a
	good grip on the bottom of the fascia panel as you move the
	oven (Fig.7-5).

Carefully push the cooker backwards o the base tray. Remove the base tray.

Position the cooker close to its nal position, leaving just enough space to get behind it.

DO NOT use the door handles or control knobs to

nn

manoeuvre the cooker.

Fig.7-3

Fig.7-4

Fig.7-5

21

Image 23

Falcon U108610-07 Lowering the Two Rear Rollers, Completing the Move, Installation, plugged into the electricity supply

Contents

U108610-07 Installation InstructionsUser Guide 90 Dual Fuel Contents nnDO NOT use a steam cleaner to clean the cooker 1. Before You StartWARNING The appliance and its accessible parts surfaces To avoid overheating, DO NOT install the cooker DO NOT store ammable materials in the storage nnThis appliance is heavy so take care when moving itAlways keep combustible materials, e.g. curtains and ammable liquids a safe distance away from your cooker Fig.2-1 2. Cooker OverviewHotplate Burners A B C D Fig.2-7 Wok BurnerFig.2-3 Fig.2-4 Fig.2-5 Fig.2-6 Always leave space around the griddle for the gases DO NOT put it crossways - it will not t properly andwill be unstable DO NOT put it on any other burner - it is not designed to t in any of the other pan supports Fig.2-12 Fig.2-16 nnNever close the grill door when the grill is onArtNo.210-0001 Classic grill control Fig.2-15 To Stop the Ovens Automatically Setting the Time of DayA B C D E F Minute Minder Fig.2-32 AUTO is Showing, But you Want to Reset to Manual CookingKey Lock Fig.2-30Fig.2-31 Fig.2-35 Oven Shelves - Left-hand Main OvenOven Shelves - Right-hand Tall Oven The Handyrack Main Oven already warm Tips on Cooking with the TimerGeneral Oven Tips DO NOT use the timed oven if the adjoining oven is 4. Cooking Table The Wok Burner 5. Cleaning Your CookerDO NOT mix dierent cleaning products - they may The Single Ring Burners Do not use steel wool, oven cleaning pads, or any ‘Cook & Clean’ PanelsBefore you remove any of the grill parts for cleaning DO NOT use harsh abrasive cleaners or sharp metal Part Recommended Cleaning MethodRemoving the Main Oven Linings Hotplate Never use caustic or abrasive cleaners as these will 6. TroubleshootingHotplate ignition or hotplate burners faulty What cleaning materials are recommended for the cooker? An oven light is not working Fig.6-1 Fig.6-2Fig.6-3 Fig.6-4 INSTALLATION 7. InstallationIf you Have a Problem Out of Warranty Failure to install the appliance correctly could Installer’s Name Installer’s Company Installer’s Telephone NumberRead the instructions before installing or using this appliance AS 5601 - ‘Gas Installations’ Checking the Parts You will also need the following tools Fig.7-1 1. Overhead - Measurement A2. Side Clearances - Measurements B & C 3. Side Clearances - Measurement D & E plugged into the electricity supply Lowering the Two Rear RollersCompleting the Move On no account try and move the cooker while it is Fitting the Restraining Chain Unless properly installed, the cooker could be tipped byFitting the Stability Bracket and Chain Fitting a Stability Bracket Propane Pressure TestingGas Connection Natural Gas Fig.7-11 Fixed WiringA N Fig.7-10 Fitting the Handles and Handrail Classic only Hotplate CheckGrill Check Oven Check Toledo - Removing the Control Panel 8. Conversion to LP GasWhen servicing or replacing gas-carrying Classic - Removing the Control Panel Fig.8-4 WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON 9. Servicing1.1 To Remove the Control Panel 1.2 To Remove the Side Panels 2.4 To Replace a Hotplate Burner Electrode 2.1 To Remove the Hotplate2.2 To Replace the Hotplate Control Taps 2.3 To Change a Hotplate Burner Injector 4.1 To Replace the Grill Controller 3.1. To Replace the Ignition or Light Switch3.2 To Replace the Clock 3.3 To Change the Ignition Generator Fig.9-4 Fig.9-5 5.3 To Change the Oven Element5.4 To Change an Oven Element Thermal Cut-out 5.5 To Replace an Oven Thermostat 6.2 To Replace the Main Oven Door 6.3 To Adjust the Main Oven Door Angle6.6 To Adjust the Main Oven Door Catch Keep 6.1 To Remove the Grill Door 6.10 To Change an Oven Door Seal 6.7 To Remove the Tall Oven Door6.8 To Replace the Tall Oven Door Outer Panel 6.9 To Replace the Tall Oven Door Magnetic Latch Colour 10. Circuit DiagramDescription COUNTRY OF DESTINATION Australia 11. Technical DataMaximum power output @ 230V 50 Hz Usable volume litresPage Page E-mail consumers@falconappliances.co.uk Clarence Street, Royal Leamington Spa Warwickshire, CV31 2AD, EnglandTel +44 0 1926 457400 Fax +44 0 1926