Replacing a Fiber Optic Module | Foundry Networks LS 648, LS 624

Installing an Optional Module into the Switch

Maintaining the FastIron LS Hardware

Installing an Optional Module into the Switch

Figure 5.1 Installing the Device in a rack mount

NOTE: The slide-in modules are not hot-swappable, you must power off the switch before installing or removing a module.

To install an optional module into the switch, do the following:

1.Remove the blank metal plate (or a previously installed module) from the appropriate slot by removing the two screws with a flat-head screwdriver.

2.Before opening the package that contains the module, touch the bag to the switch casing to discharge any potential static electricity. Also, it is recommended to use an ESD wrist strap during installation.

3.Remove the module from the anti-static shielded bag.

4.Holding the module level, guide it into the carrier rails on each side and gently push it all the way into the slot, ensuring that it firmly engages with the connector.

5.If you are sure the module is properly mated with the connector, tighten the retainer screws to secure the module in the slot.

6.When the device is powered on, the Module LED on the switch’s front panel should turn green to confirm that the module is correctly installed and ready to use.

Removing a 10-Gigabit Ethernet Module

1.Remove the 10-Gigabit module:

•Use a #2 Phillips-head screwdriver to loosen and remove the two screws on the 10-Gigabit module.

•Gently lift the module up and out of the device.

2.Place the 10-Gigabit module in an anti-static bag for storage.

3.Do one of the following:

•Insert the new 10-Gigabit module as instructed in the section “Installing an Optional Module into the Switch” on page 5-5.

•If you are removing the module without replacing it, install the blank face place in the rear panel.

Replacing a Fiber Optic Module

You can remove an SFP or XFP from a port and replace it with a new one while the FastIron LS is powered on and running.

This section provides information about the following tasks:

•Removing a fiber optic module

•Installing a new fiber optic module

•Cabling a fiber optic module

September 2007

© 2007 Foundry Networks, Inc.

5 - 5

Image 47

Foundry Networks LS 648, LS 624 manual Replacing a Fiber Optic Module, Installing an Optional Module into the Switch

Contents

FGS Release Foundry FastIron LS Layer 2 Compact SwitchHardware Installation Guide FastIron LS FastIron LS Copyright 2007 Foundry Networks, Inc. All rights reserved CHAPTER INSTALLING A FASTIRON LS SWITCHABOUT THIS GUIDE PRODUCT OVERVIEW C ONNECTING N ETWORK D EVICES AND C HECKING C ONNECTIVITYM AINTAINING THE F AST I RON LS H ARDWARE C HAPTER REGULATORY STATEMENTS APPENDIX AHARDWARE SPECIFICATIONS W ARNINGS C AUTIONS AND W ARNINGSA PPENDIX B C AUTIONS Audience Chapter About This GuideIntroduction What’s Included in This Edition? Email Access How to Get HelpWarranty Coverage Web Access Table 2.1 Chapter Contents Hardware FeaturesChapter Product Overview FLS624, FLS648 FastIron LS Network Interfaces Control FeaturesReset Button Serial Management Interface Console Port Interface Network InterfacesFastIron LS 10/100/1000BASE-T Ports Table 2.2 Network Interfaces 10-GbE CX4 Module 10 Gigabit Ethernet Module SlotsCable Specifications for New Module 10 Gbps CX4 Ports Condition Port, System and Module Status LEDsCX4 Transceiver Infiniband cable Table 2.3 Port Status LEDs System LEDs Table 2.4 Status LEDs Fiber Optic Modules Power SuppliesOptional Redundant Power Supply Power Supply Receptacles September Table 3.1 Chapter Contents Chapter Installing a FastIron LS SwitchUnpacking a System General Requirements Package Contents Foundry FastIron Configuration Guide Summary of Installation TasksTable 3.2 Summary of Installation Tasks Where to Find More Information Power Precautions Installation PrecautionsGeneral Precautions Lifting Precautions Cabling Infrastructure Preparing the Installation SiteInstallation Location Installing the Device Figure 3.1 Attaching the adhesive feet Desktop InstallationRack Mount Installation Figure 3.2 Attaching the brackets Wall Mount InstallationFigure 3.3 Installing the device in a rack Package Contents Installing a Redundant Power SupplyAbout the RPS2-EIF Redundant Power Supply Features and Benefits FastIron RPS2-EIF LEDsPort Indicators System Indicators Mounting Installing a FastIron LS Redundant Power SupplyEquipment Checklist Installation Figure 3.5 Attaching the brackets Desktop or Shelf MountingFigure 3.6 Installing the RPS in a Rack FastIron LS648 Connecting Switches to the RPS FLS units GND N.C Installing an Optional Module into the SwitchPorts Pin-Out RPS2-EIF GND N.C RPS Present Status Status Power Good GND Figure 3.10 Inserting an SFP transceiver into a slot Installing an SFP Transceiver Attaching a PC or Terminal Powering On the SystemVerifying Proper Operation Null Modem Wiring Map for Serial CableTable 3.3 Serial Cable Wiring Switch’s 9-Pin September Step Chapter Connecting Network Devices and Checking ConnectivityAssigning Permanent Passwords Table 4.1 Network Connectivity Tasks FLS648 Switchconfig# enable super-user-password text Recovering from a Lost PasswordFLS648 Switch enable FLS648 Switch# configure terminal FLS648 Switchconfig# Devices Running Layer 2 Software Configuring IP Addresses Connecting to Ethernet or Fast Ethernet Hubs Connecting Network DevicesConnectors Cable Specifications Automatic MDI/MDIX Detection Connecting to Workstations, Servers, or RoutersConnecting a Network Device to a Fiber Port Installing a Fiber Optic Module Cabling a Fiber Optic Module Testing ConnectivityCleaning the Fiber-Optic Connectors Observing LEDs Meaning Troubleshooting Network ConnectionsTable 4.2 Network Connection-Related LED States Desired Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide Table 5.1 Chapter Contents Managing FastIron LS Temperature SettingsUsing the Temperature Sensor on the FastIron LS Chapter Maintaining the FastIron LS Hardware Power supply 2 NA - AC - Regular present, status ok Fan 1 failed Displaying the Temperature on the FastIron LSDisplaying Syslog Messages for Temperature on the FastIron LS FLS648 Switch show chassis Power supply 1 not present FLS648 Switch# show log Changing the Temperature Polling Interval Hardware Maintenance ScheduleInstalling or Replacing a 10-Gigabit Ethernet Module Displaying Management Module CPU Usage Removing a 10-Gigabit Ethernet Module Installing an Optional Module into the SwitchReplacing a Fiber Optic Module Bail Latch Installing a New Fiber Optic ModuleRemoving a Fiber Optic Module Digital Optical Monitoring Cleaning the Fiber-Optic ConnectorsCabling a Fiber Optic Module Status Value Supported MediaTable 5.2 Status Value Description show optic port/slotnumber CLI Commandsno optical-monitor alarm interval September Symptom Chapter TroubleshootingDiagnosing Switch Indicators Table 0.1 Troubleshooting Chart In-Band Access Power and Cooling ProblemsInstallation Redundant Power supply specifications Chapter Hardware SpecificationsTable 0.2 Chapter Contents FastIron LS specifications Operating Environment FastIron LS SpecificationsPhysical Dimensions Environmental Considerations Table 0.7 Storage Environment CoolingStorage Environment Mean Time Before Failure Fan Speed Table 0.9 Fan Noise Levels for FastIron LS 24-Port SwitchTable 0.10 Fan Noise Levels for FastIron LS 48-Port Switch Chassis side Table 0.11 Regulatory Compliance and Safety Approvals Certifications Regulatory ComplianceFCC CFR 47 Part 15 Warning CISPR 22 CLASS A Warning Serial Console Port Pinouts WarrantyPinouts and Signaling VCCI Cable Type1 Connector TypeLC connector for Table 0.12 Cable length summary table Cable Type Table 0.12 Cable length summary table Continued Property AC Power SupplySpecifications Table 0.13 Specifications for AC Power Physical Dimensions and Weight Redundant Power Supply SpecificationsPower Cords Key features Input Connector Properties Input ConnectorElectromagnetic Compatibility EMC and Immunity Standards Table 0.15 Input Connector for Power Supplies Table 0.17 Safety Warning Labels on Power Supplies Safety Agency Approvals and CertificationsSafety Warnings Environmental Considerations Table 0.19 Mean Time Before Failure Specifiations Electrical SpecificationsInput specifications Table 0.20 Input Specifications for Power Supplies September Europe and Australia Appendix A Regulatory StatementsU.S.A Industry Canada Statement September Cautions Appendix B Cautions and Warnings Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide Cautions and Warnings CAUTION Never leave tools inside the device Warnings Page Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide