Installation Precautions | Foundry Networks LS 624, LS 648 manual

Installation Precautions

Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide

Installation Precautions

Follow these precautions when installing a Foundry device.

General Precautions

WARNING: All fiber-optic interfaces use Class 1 lasers.

CAUTION: Do not install the device in an environment where the operating ambient temperature might exceed 50o C (121o F).

CAUTION: Make sure the air flow around the front, sides, and back of the device is not restricted.

CAUTION: Never leave tools inside the device.

Lifting Precautions

WARNING: Make sure the rack or cabinet housing the device is adequately secured to prevent it from becoming unstable or falling over.

WARNING: Mount the devices you install in a rack or cabinet as low as possible. Place the heaviest device at the bottom and progressively place lighter devices above.

Power Precautions

CAUTION: Use a separate branch circuit for each AC power cord, which provides redundancy in case one of the circuits fails.

CAUTION: To avoid high voltage shock, do not open the device while the power is on.

CAUTION: Ensure that the device does not overload the power circuits, wiring, and over-current protection. To determine the possibility of overloading the supply circuits, add the ampere (amp) ratings of all devices installed on the same circuit as the device. Compare this total with the rating limit for the circuit. The maximum ampere rat- ings are usually printed on the devices near the input power connectors.

WARNING: Disconnect the power cord from all power sources to completely remove power from the device.

WARNING: If the installation requires a different power cord than the one supplied with the device, make sure you use a power cord displaying the mark of the safety agency that defines the regulations for power cords in your country. The mark is your assurance that the power cord can be used safely with the device.

3 - 4

© 2007 Foundry Networks, Inc.

September 2007

Image 20

Foundry Networks LS 624, LS 648 manual Installation Precautions, General Precautions, Lifting Precautions, Power Precautions

Contents

Foundry FastIron LS Layer 2 Compact Switch Hardware Installation GuideFastIron LS FastIron LS FGS Release Copyright 2007 Foundry Networks, Inc. All rights reserved INSTALLING A FASTIRON LS SWITCH ABOUT THIS GUIDEPRODUCT OVERVIEW CHAPTER C HECKING C ONNECTIVITY M AINTAINING THE F AST I RON LS H ARDWAREC HAPTER C ONNECTING N ETWORK D EVICES AND REGULATORY STATEMENTS APPENDIX AHARDWARE SPECIFICATIONS C AUTIONS AND W ARNINGS A PPENDIX BC AUTIONS W ARNINGS Chapter About This Guide IntroductionWhat’s Included in This Edition? Audience How to Get Help Warranty CoverageWeb Access Email Access Hardware Features Chapter Product OverviewFLS624, FLS648 Table 2.1 Chapter Contents Control Features Reset ButtonSerial Management Interface Console Port FastIron LS Network Interfaces Network Interfaces FastIron LS 10/100/1000BASE-T PortsTable 2.2 Network Interfaces Interface 10 Gigabit Ethernet Module Slots Cable Specifications for New Module10 Gbps CX4 Ports 10-GbE CX4 Module Port, System and Module Status LEDs CX4 Transceiver Infiniband cableTable 2.3 Port Status LEDs Condition Table 2.4 Status LEDs System LEDs Power Supplies Optional Redundant Power SupplyPower Supply Receptacles Fiber Optic Modules 2007 Foundry Networks, Inc Table 3.1 Chapter Contents Chapter Installing a FastIron LS SwitchUnpacking a System Package Contents General Requirements Summary of Installation Tasks Table 3.2 Summary of Installation TasksWhere to Find More Information Foundry FastIron Configuration Guide Installation Precautions General PrecautionsLifting Precautions Power Precautions Preparing the Installation Site Installation LocationInstalling the Device Cabling Infrastructure Figure 3.1 Attaching the adhesive feet Desktop InstallationRack Mount Installation Figure 3.2 Attaching the brackets Wall Mount InstallationFigure 3.3 Installing the device in a rack Installing a Redundant Power Supply About the RPS2-EIF Redundant Power SupplyFeatures and Benefits Package Contents LEDs Port IndicatorsSystem Indicators FastIron RPS2-EIF Installing a FastIron LS Redundant Power Supply Equipment ChecklistInstallation Mounting Figure 3.5 Attaching the brackets Desktop or Shelf MountingFigure 3.6 Installing the RPS in a Rack Connecting Switches to the RPS FastIron LS648 FLS units Installing an Optional Module into the Switch Ports Pin-Out RPS2-EIFGND N.C RPS Present Status Status Power Good GND GND N.C Installing an SFP Transceiver Figure 3.10 Inserting an SFP transceiver into a slot Attaching a PC or Terminal Powering On the SystemVerifying Proper Operation Wiring Map for Serial Cable Table 3.3 Serial Cable WiringSwitch’s 9-Pin Null Modem 2007 Foundry Networks, Inc Chapter Connecting Network Devices and Checking Connectivity Assigning Permanent PasswordsTable 4.1 Network Connectivity Tasks Step Recovering from a Lost Password FLS648 Switch enableFLS648 Switch# configure terminal FLS648 Switchconfig# FLS648 Switchconfig# enable super-user-password text Configuring IP Addresses Devices Running Layer 2 Software Connecting Network Devices ConnectorsCable Specifications Connecting to Ethernet or Fast Ethernet Hubs Connecting to Workstations, Servers, or Routers Connecting a Network Device to a Fiber PortInstalling a Fiber Optic Module Automatic MDI/MDIX Detection Testing Connectivity Cleaning the Fiber-Optic ConnectorsObserving LEDs Cabling a Fiber Optic Module Troubleshooting Network Connections Table 4.2 Network Connection-Related LED StatesDesired Meaning Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide Managing FastIron LS Temperature Settings Using the Temperature Sensor on the FastIron LSChapter Maintaining the FastIron LS Hardware Table 5.1 Chapter Contents Displaying the Temperature on the FastIron LS Displaying Syslog Messages for Temperature on the FastIron LSFLS648 Switch show chassis Power supply 1 not present Power supply 2 NA - AC - Regular present, status ok Fan 1 failed FLS648 Switch# show log Hardware Maintenance Schedule Installing or Replacing a 10-Gigabit Ethernet ModuleDisplaying Management Module CPU Usage Changing the Temperature Polling Interval Removing a 10-Gigabit Ethernet Module Installing an Optional Module into the SwitchReplacing a Fiber Optic Module Bail Latch Installing a New Fiber Optic ModuleRemoving a Fiber Optic Module Digital Optical Monitoring Cleaning the Fiber-Optic ConnectorsCabling a Fiber Optic Module Status Value Supported MediaTable 5.2 Status Value Description show optic port/slotnumber CLI Commandsno optical-monitor alarm interval 2007 Foundry Networks, Inc Chapter Troubleshooting Diagnosing Switch IndicatorsTable 0.1 Troubleshooting Chart Symptom In-Band Access Power and Cooling ProblemsInstallation Chapter Hardware Specifications Table 0.2 Chapter ContentsFastIron LS specifications Redundant Power supply specifications FastIron LS Specifications Physical DimensionsEnvironmental Considerations Operating Environment Cooling Storage EnvironmentMean Time Before Failure Table 0.7 Storage Environment Table 0.9 Fan Noise Levels for FastIron LS 24-Port Switch Table 0.10 Fan Noise Levels for FastIron LS 48-Port SwitchChassis side Fan Speed Regulatory Compliance FCC CFR 47 Part 15 WarningCISPR 22 CLASS A Warning Table 0.11 Regulatory Compliance and Safety Approvals Certifications Warranty Pinouts and SignalingVCCI Serial Console Port Pinouts Connector Type LC connector forTable 0.12 Cable length summary table Cable Type1 Table 0.12 Cable length summary table Continued Cable Type AC Power Supply SpecificationsTable 0.13 Specifications for AC Power Property Redundant Power Supply Specifications Power CordsKey features Physical Dimensions and Weight Input Connector Electromagnetic Compatibility EMC and Immunity StandardsTable 0.15 Input Connector for Power Supplies Input Connector Properties Safety Agency Approvals and Certifications Safety WarningsEnvironmental Considerations Table 0.17 Safety Warning Labels on Power Supplies Electrical Specifications Input specificationsTable 0.20 Input Specifications for Power Supplies Table 0.19 Mean Time Before Failure Specifiations 2007 Foundry Networks, Inc Appendix A Regulatory Statements U.S.AIndustry Canada Statement Europe and Australia 2007 Foundry Networks, Inc Appendix B Cautions and Warnings Cautions Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide Cautions and Warnings CAUTION Never leave tools inside the device Warnings Page Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide