Installing an SFP Transceiver | Foundry Networks LS 648, LS 624

Installing an SFP Transceiver

Installing a FastIron LS Switch

NOTE: Slide-in modules are not hot-swappable. You must power off the switch before installing or removing a module.

To install an optional module into the switch, do the following:

1.Remove the blank metal plate (or a previously installed module) from the appropriate slot by removing the two screws with a flat-head screwdriver.

2.Before opening the package that contains the module, touch the bag to the switch casing to discharge any potential static electricity. Foundry recommends using an ESD wrist strap during installation.

3.Remove the module from the anti-static shielded bag.

4.Holding the module level, guide it into the carrier rails on each side and gently push it all the way into the slot, ensuring that it firmly engages with the connector.

5.When you are sure the module has properly engaged the connector, tighten the retainer screws to secure the module in the slot.

6.When the device is powered on, the module LED on the switch’s front panel should turn green to confirm that the module is correctly installed and ready to use.

CAUTION: If you do not install a module in a slot, you must keep the slot panel in place. If you run the device with an uncovered slot, the system will overheat.

Installing an SFP Transceiver

Figure 3.10 Inserting an SFP transceiver into a slot

FLS 624

Fastlron LS 624

See Table 0.12 on page 2-7for a list of compatible transceivers. To install an SFP transceiver, do the following:

1.Consider network and cabling requirements to select an appropriate SFP transceiver type.

2.Insert the transceiver with the optical connector facing outward and the slot connector facing down. SFP transceivers are keyed so they can only be installed in one orientation.

3.Slide the SFP transceiver into the slot until it clicks into place.

NOTE: SFP transceivers are hot-swappable. The switch does not need to be powered off before installing or removing a transceiver. However, always first disconnect the network cable before removing a transceiver.

NOTE: SFP transceivers are not provided in the switch package.

September 2007

© 2007 Foundry Networks, Inc.

3 - 15

Image 31

Foundry Networks LS 648, LS 624 manual Installing an SFP Transceiver, 10 Inserting an SFP transceiver into a slot

Contents

FGS Release Foundry FastIron LS Layer 2 Compact SwitchHardware Installation Guide FastIron LS FastIron LS Copyright 2007 Foundry Networks, Inc. All rights reserved CHAPTER INSTALLING A FASTIRON LS SWITCHABOUT THIS GUIDE PRODUCT OVERVIEW C ONNECTING N ETWORK D EVICES AND C HECKING C ONNECTIVITYM AINTAINING THE F AST I RON LS H ARDWARE C HAPTER HARDWARE SPECIFICATIONS APPENDIX AREGULATORY STATEMENTS W ARNINGS C AUTIONS AND W ARNINGSA PPENDIX B C AUTIONS Audience Chapter About This GuideIntroduction What’s Included in This Edition? Email Access How to Get HelpWarranty Coverage Web Access Table 2.1 Chapter Contents Hardware FeaturesChapter Product Overview FLS624, FLS648 FastIron LS Network Interfaces Control FeaturesReset Button Serial Management Interface Console Port Interface Network InterfacesFastIron LS 10/100/1000BASE-T Ports Table 2.2 Network Interfaces 10-GbE CX4 Module 10 Gigabit Ethernet Module SlotsCable Specifications for New Module 10 Gbps CX4 Ports Condition Port, System and Module Status LEDsCX4 Transceiver Infiniband cable Table 2.3 Port Status LEDs System LEDs Table 2.4 Status LEDs Fiber Optic Modules Power SuppliesOptional Redundant Power Supply Power Supply Receptacles September Unpacking a System Chapter Installing a FastIron LS SwitchTable 3.1 Chapter Contents General Requirements Package Contents Foundry FastIron Configuration Guide Summary of Installation TasksTable 3.2 Summary of Installation Tasks Where to Find More Information Power Precautions Installation PrecautionsGeneral Precautions Lifting Precautions Cabling Infrastructure Preparing the Installation SiteInstallation Location Installing the Device Rack Mount Installation Desktop InstallationFigure 3.1 Attaching the adhesive feet Figure 3.3 Installing the device in a rack Wall Mount InstallationFigure 3.2 Attaching the brackets Package Contents Installing a Redundant Power SupplyAbout the RPS2-EIF Redundant Power Supply Features and Benefits FastIron RPS2-EIF LEDsPort Indicators System Indicators Mounting Installing a FastIron LS Redundant Power SupplyEquipment Checklist Installation Figure 3.6 Installing the RPS in a Rack Desktop or Shelf MountingFigure 3.5 Attaching the brackets FastIron LS648 Connecting Switches to the RPS FLS units GND N.C Installing an Optional Module into the SwitchPorts Pin-Out RPS2-EIF GND N.C RPS Present Status Status Power Good GND Figure 3.10 Inserting an SFP transceiver into a slot Installing an SFP Transceiver Verifying Proper Operation Powering On the SystemAttaching a PC or Terminal Null Modem Wiring Map for Serial CableTable 3.3 Serial Cable Wiring Switch’s 9-Pin September Step Chapter Connecting Network Devices and Checking ConnectivityAssigning Permanent Passwords Table 4.1 Network Connectivity Tasks FLS648 Switchconfig# enable super-user-password text Recovering from a Lost PasswordFLS648 Switch enable FLS648 Switch# configure terminal FLS648 Switchconfig# Devices Running Layer 2 Software Configuring IP Addresses Connecting to Ethernet or Fast Ethernet Hubs Connecting Network DevicesConnectors Cable Specifications Automatic MDI/MDIX Detection Connecting to Workstations, Servers, or RoutersConnecting a Network Device to a Fiber Port Installing a Fiber Optic Module Cabling a Fiber Optic Module Testing ConnectivityCleaning the Fiber-Optic Connectors Observing LEDs Meaning Troubleshooting Network ConnectionsTable 4.2 Network Connection-Related LED States Desired Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide Table 5.1 Chapter Contents Managing FastIron LS Temperature SettingsUsing the Temperature Sensor on the FastIron LS Chapter Maintaining the FastIron LS Hardware Power supply 2 NA - AC - Regular present, status ok Fan 1 failed Displaying the Temperature on the FastIron LSDisplaying Syslog Messages for Temperature on the FastIron LS FLS648 Switch show chassis Power supply 1 not present FLS648 Switch# show log Changing the Temperature Polling Interval Hardware Maintenance ScheduleInstalling or Replacing a 10-Gigabit Ethernet Module Displaying Management Module CPU Usage Replacing a Fiber Optic Module Installing an Optional Module into the SwitchRemoving a 10-Gigabit Ethernet Module Removing a Fiber Optic Module Installing a New Fiber Optic ModuleBail Latch Cabling a Fiber Optic Module Cleaning the Fiber-Optic ConnectorsDigital Optical Monitoring Table 5.2 Status Value Description Supported MediaStatus Value no optical-monitor alarm interval CLI Commandsshow optic port/slotnumber September Symptom Chapter TroubleshootingDiagnosing Switch Indicators Table 0.1 Troubleshooting Chart Installation Power and Cooling ProblemsIn-Band Access Redundant Power supply specifications Chapter Hardware SpecificationsTable 0.2 Chapter Contents FastIron LS specifications Operating Environment FastIron LS SpecificationsPhysical Dimensions Environmental Considerations Table 0.7 Storage Environment CoolingStorage Environment Mean Time Before Failure Fan Speed Table 0.9 Fan Noise Levels for FastIron LS 24-Port SwitchTable 0.10 Fan Noise Levels for FastIron LS 48-Port Switch Chassis side Table 0.11 Regulatory Compliance and Safety Approvals Certifications Regulatory ComplianceFCC CFR 47 Part 15 Warning CISPR 22 CLASS A Warning Serial Console Port Pinouts WarrantyPinouts and Signaling VCCI Cable Type1 Connector TypeLC connector for Table 0.12 Cable length summary table Cable Type Table 0.12 Cable length summary table Continued Property AC Power SupplySpecifications Table 0.13 Specifications for AC Power Physical Dimensions and Weight Redundant Power Supply SpecificationsPower Cords Key features Input Connector Properties Input ConnectorElectromagnetic Compatibility EMC and Immunity Standards Table 0.15 Input Connector for Power Supplies Table 0.17 Safety Warning Labels on Power Supplies Safety Agency Approvals and CertificationsSafety Warnings Environmental Considerations Table 0.19 Mean Time Before Failure Specifiations Electrical SpecificationsInput specifications Table 0.20 Input Specifications for Power Supplies September Europe and Australia Appendix A Regulatory StatementsU.S.A Industry Canada Statement September Cautions Appendix B Cautions and Warnings Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide Cautions and Warnings CAUTION Never leave tools inside the device Warnings Page Foundry FastIron LS Layer 2 Compact Switch Hardware Installation Guide