8196339
24-Hour Service Hotline
PROTECTOR SERIES GAS FRYERS
APRIL
NOTICE TO U.S. CUSTOMERS
DANGER
1.1 Applicability and Validity
1.2 Safety Information
PROTECTOR SERIES GAS FRYER CHAPTER 1 GENERAL INFORMATION
DANGER
1.4 European Community CE Specific Information
Non-CE Standard for Incoming Gas Pressures
1.3 Computer Information for the CM7 Computers
1.7 Definitions
1.6 Installation, Operating, and Service Personnel
1.5 Equipment Description
What to do if your equipment arrives damaged
1.8 Shipping Damage Claim Procedure
1.9 Parts Ordering and Service Information
RETAIN AND STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE USE
2.1.1 Clearance and Ventilation
PROTECTOR SERIES GAS FRYER CHAPTER 2 INSTALLATION INSTRUCTIONS
2.1 General Installation Requirements
Do not block the area around the base or under the fryers
DANGER
2.1.2 National Code Requirements
One of the most important considerations of efficient fryer operation is ventilation. Make sure the fryer is installed so that products of combustion are removed efficiently, and that the kitchen ventilation system does not produce drafts that interfere with burner operation
DANGER
2.1.4 Australian Requirements
2.2 Caster/Leg Installation
2.1.3 Electrical Grounding Requirements
2.3 Pre-Connection Preparations DANGER
DANGER
Non-CE Standard for Incoming Gas Pressures
DANGER
2.4 Connection to Gas Line DANGER
DANGER
DANGER
Required airflow for the combustion air supply is 2m3/h per kW
CE Standard
DANGER
Refer to chapter 4 CM7 Computer your particular controller
2.5 Converting to another Gas Type
DANGER
2.6 Positioning the Fryer
1. Once the fryer has been positioned at the frying station, use a carpenter’s level placed across the top of the frypot to verify that the unit is level, both side-to-side and front-to-back
DANGER
PROTECTOR SERIES GAS FRYER CHAPTER 3 OPERATING INSTRUCTIONS
FINDING YOUR WAY AROUND THE PROTECTOR SERIES GAS FRYER
3.1 Controller Operation and Programming
3.2 Equipment Setup and Start-Up Procedures
3.2.1 Setup
CM7 COMPUTER
3.2.2 Lighting the Fryer
3.3 Boiling Out the Frypot
3.4 Shutting the Fryer Down
3.5.1 Prepare the System for Use
3.5.2 Install the Oil Reservoir
3.5 Oil Attendant Automatic Top-Off
3.5.3 Routine Oil Changes
3.5.4 Bulk Oil Systems
PROTECTOR SERIES GAS FRYERS CHAPTER 4 CM7 COMPUTER INSTRUCTIONS
4.1 CM7 General Information
4.2 Basic Operation
4.3 Cooking with Multi-Product Display
FR FRIES
4.4 Cooking with Dedicated Display
FR FRIES
4.5 Changing from Breakfast Setup to Lunch
4.6 Changing from Lunch Setup to Breakfast
4.7.2 Temperature and Unlock Buttons
4.7 CM7 Button Description and Functions
4.7.1 Navigation Buttons
4.7.3 Cook Cycle and Selection Buttons
Storing Product Menu Items in Product Buttons
4.8 CM7 Menu Summary Tree
Adding New Product Menu Items
Temperature Conversion from F to C
7378
4.9 Setup Mode Programming
SETUP
12hr
9. Use the 3and 4 buttons see Figure 12 to toggle between am and pm
The computer displays Oil SYSTEM on the left and JIB on the right
The computer displays FRYER Setup for three seconds then off
The computer displays VAT type on the left and SPLIT on the right
The computer displays TEMPERATURE on the left and F on the right
4.10.2 Adding New Product Items to the Menu
4.10 CM7 Common Tasks
4.10.1 Escape Menu Items
Covered in this section are common tasks used in stores
6. With the desired temperature entered, press the button see Figure
SENSITIVITY
4.10.3 Storing Menu Items in Product Buttons
1658
4.11 Boil-Out Mode
4.10.4 Temperature conversion from F to C
6. Press the 9 1 button see Figure
SETPOINT TEMPERATURE
DANGER
1650
DANGER
4.11.1 Clean Filter Pan, Detachable Parts and Accessories
DANGER
4-18
4321
Error Codes E01 - Right Remove Discard E02 - Left Remove Discard
4.12 Manager Mode
to E-LOG
off, 1 the softest and 9 the loudest
Sensitivity Setting
4.13 SENSITIVITY SETTINGS CHART
Sensitivity Settings for Various Products
Product
DANGER
PROTECTOR SERIES GAS FRYERS CHAPTER 5 FILTRATION INSTRUCTIONS
5.1 Draining and Manual Filtering DANGER
DANGER
DANGER
5.2 Preparing the Built-In Filtration System for Use
Magnasol Filter - includes crumb tray and Magnasol filter assembly
DANGER
5.2.1 Preparation for Use with Filter Paper or Filter Pad
5.2.2 Preparation for Use with the Magnasol Filter Assembly
DANGER
5.3 Operation of the Filter
alternating with YES NO
DANGER
The computer displays FILTER DONE alternating with YES NO
DANGER
DANGER
2. Separate the outer screens and grid
5.4 Disassembly and Reassembly of the Magnasol Filter Dissassembly
DANGER
Cleaning
Reassembly
DANGER
5.6 Using the “Optional” Oil Disposal
5.5 Draining and Disposing of Waste Oil
DANGER
6.2 DAILY CHECKS AND SERVICE
PROTECTOR SERIES GAS FRYERS CHAPTER 6 PREVENTIVE MAINTENANCE
6.1 FRYER PREVENTATIVE MAINTENANCE CHECKS AND SERVICE DANGER
6.2.1 Inspect Fryer and Accessories for Damage
6.3.2 Boiling Out the Frypot
6.3 WEEKLY CHECKS AND SERVICE 6.3.1 Drain and Clean Frypot DANGER
6.4 MONTHLY CHECKS AND SERVICE
6.4.1 Check Computer Magic 7 Set Point Accuracy
1. Disconnect the blower wiring harness and remove the four blower mounting nuts see Figure 1 below
5. Reinstall the blower shield or shield assembly
6.7 Annual/Periodic System Inspection
6.6 SEMI-ANNUAL CHECKS AND SERVICE 6.6.1 Clean Gas Valve Vent Tube
6.6.2 Check Burner Manifold Pressure DANGER
6.7.1 Fryer
6.7.2 Built-In Filtration System
Page
Before calling a servicer or the Frymaster HOTLINE
PROTECTOR SERIES GAS FRYERS CHAPTER 7 OPERATOR TROUBLESHOOTING
7.1 Introduction
DANGER
PROBABLE CAUSES
7.2 Troubleshooting Fryers 7.2.1 Computer and Heating Problems
PROBLEM
CORRECTIVE ACTION
Probable Causes
7.2.2 Error Messages and Display Problems
Corrective Action
IGNITION
PROBLEM
Problem
7.2.3 Filtration Problems
Probable Causes
Problem
7.2.4 Auto Top-Off Problems
7.2.5 Basket Lift Problems
PROBLEM
TEL 1-318-865-1711 FAX Parts 1-318-219-7140 FAX Tech Support
SERVICE HOTLINE
Shipping Address 8700 Line Avenue, Shreveport, Louisiana
819-6339