6.6Replacing Components

6.6.1 Replacing the Controller or Controller Wiring Harness

Refer to Chapter 5, Section 5.3 for this procedure.

6.6.2 Replacing the Temperature Probe

1.Unplug the rethermalizer and drain the cookpot.

2.Remove the screws from the upper corners of the timer panel and swing the panel open from the top, allowing it to rest on its hinge tabs. Cut the probe leads off at the rear of the probe. NOTE: Once the probe leads have been cut, the probe cannot be reused. Work the Tinnerman retaining clip rearward off the probe.

3.Remove the two screws securing the probe cover to the probe block and remove the cover. Slip the failed probe out of the block from the cookpot side and replace with a new probe. Carefully remove the Tinnerman retaining clip from the replacement probe to allow the leads and short end of the probe to be inserted through the probe block from cookpot side. When the replacement probe has been inserted, work the retaining clip onto the probe until the probe is held securely in place. Reinstall the probe cover and timer panel.

4.Remove the screws from the upper corners of the control panel and swing the panel open from the top, allowing it to rest on its hinge tabs. Remove the two upper screws securing the compo- nent box to the rethermalizer. Rotate the box forward and outward to expose the 12-pin connec- tor on the rear of the interface board.

5.Unplug the 12-pin connector from the interface board. Using a pin pusher, remove the cut off pieces of wire from the connector one at a time, and insert the corresponding wire from the new probe.

6.Reattach the 12-pin connector to the interface board, rotate the component box back into posi- tion, and replace and tighten the mounting screws. Close the control panel and replace the screws in each upper corner.

6.6.3 Replacing the Interface Board

1.Unplug the rethermalizer and drain the cookpot.

2.Remove the screws from the upper corners of the control panel and swing the panel open from the top, allowing it to rest on its hinge tabs.

3.Detach the grounding wire from the controller, unplug the 15-pin connector from the interface board, and remove the control panel from the unit by lifting it up and out of the hinge slots in the control panel frame.

4.Remove the two upper screws securing the component box to the rethermalizer. Rotate the box forward and outward to expose the 12-pin connector on the rear of the interface board, and un- plug it from the board.

6-5

Page 31 Page 33
Page 32
Image 32
Frymaster FBR18 Series manual Replacing the Temperature Probe, Replacing the Interface Board
Page 31 Page 33

FBR18 Series specifications

The Frymaster FBR18 Series stands out in the commercial kitchen arena for its innovative design, robust features, and advanced frying technologies. This series is specifically engineered to meet the demands of busy restaurants, fast-food establishments, and large-scale food service operations. With a focus on efficiency, durability, and food quality, the FBR18 Series has become a preferred choice for chefs and kitchen managers looking for reliable frying equipment.

One of the main features of the Frymaster FBR18 Series is its industry-leading oil filtration system. This self-filtering capability ensures that oil remains clean and minimizes the frequency of oil changes, leading to significant cost savings over time. The filtration system is designed for easy operation, allowing kitchen staff to focus on food preparation rather than maintenance.

The FBR18 Series is built with stainless steel construction, which enhances durability and simplifies cleaning. The sturdy design can withstand the rigors of a bustling kitchen environment. Additionally, the fryers are equipped with advanced heating technology, including high-efficiency gas burners that provide even heat distribution and reduce recovery time. This results in faster cooking cycles and improved product quality.

Temperature control is another hallmark of the FBR18 Series. With precise digital controls and built-in temperature monitoring, chefs can achieve optimal frying results every time, ensuring consistent quality across batches. The fryers are designed with safety features, including a shut-off mechanism that activates when the fry pot reaches an unsafe temperature, ensuring the safety of both the equipment and kitchen staff.

The FBR18 Series also offers versatility with multiple frying basket options, allowing operators to fry a variety of items simultaneously. The fry pots are spacious and can accommodate larger volumes, making them ideal for high-demand settings. This series is compatible with various frying mediums, including standard oils and specialty options, providing flexibility for different menu items.

In terms of energy efficiency, the Frymaster FBR18 Series incorporates various features aimed at reducing gas or electric consumption without sacrificing performance. This not only helps in lowering operational costs but also aligns with growing sustainability practices in the food service industry.

Overall, the Frymaster FBR18 Series combines cutting-edge technologies and practical features to deliver an exceptional frying experience. Its reliability, efficiency, and compliance with health and safety regulations make it an excellent investment for any commercial kitchen looking to elevate its frying capabilities. With an emphasis on quality and operator convenience, the FBR18 Series is a game-changer in modern frying solutions.
Top Page Image Contents