Turning Off the Power Supply, Turning off the power | Fujitsu 500

7 Turning Off the Power Supply

Cautions

•Before turning off the power, terminate all work and save data.

•Before turning off the power, confirm that the Floppy disk drive access lamp and the Hard disk drive access lamp are off. If the power is turned off while the lamps are on, data being processed may not be saved or data on the floppy disk or hard disk may be damaged.

•If the power cable is pulled out from the outlet while the power is on or if power is interrupted by a power failure, connect the power cable to the outlet again or wait until the power is restored. You do not have to press the power switch. Once the power is restored, the PC automatically turns on and starts up. However, when [Power-saving settings] - [Action at AC power restoration] of BIOS Setup is set to [Power off], the system does not turn on.

•On Windows 95 models, when [Power saving by APM] of BIOS Setup is set to [Disabled], they do not turn off automatically.

•Do not turn off the system during POST (power-on self-test). After the OS starts up, turn off the system in the following procedure.

•If the system does not shut down or restart in the normal procedure, press the power switch for four or more seconds until the power is turned off. However, use this procedure in an emergency only, because this may damage the hard disk.

Turning off the power

Windows Me

1Click the [Start] button, then click [Shut down Windows]. The [Shut down Windows] dialog box appears.

2Select [Shutdown] and click [OK]. The power is turned off.

Point

•The power can be turned off in the following procedure.

1Press the [Ctrl] + [Alt] + [Delete] keys. The [Abort programs] dialog box appears.

2Click [Shutdown].

The power is turned off.

23

Image 34

Fujitsu 500 user manual Turning Off the Power Supply, Turning off the power, Windows Me

Contents

Deskpower 5000 Series User’s Manual Important Safety Instructions Iii Before Starting Your PC Safety product applicationsFor Safe Operations Conventions used in this manual Point Diskcopy a a Command entry from keyboardCD-ROM drive¥setup.exe Sample screens Illustrations Deskpower Rear surface of the equipment Manual configuration Introduction Content Introduction Chapter Hardware Specifications Chapter Part Names and Functions Front of the PC unit Hard disk access lamp Power lampPower switch Floppy disk drive access lamp Rear of the PC unit CRT connector Keyboard connector Connect the keyboard Serial connectorParallel connector DVI connector Inside the PC unit Power supply unit Inch front access bayInternal hard disk drive Internal battery Primary IDE connector IDE1Dimm slots Keyboard Windows key Caps Lock/Alphanumeric keyCtrl control key Alt key Mouse Using the mouseUsing the mouse buttons Moving the mouse Pointing Double-clickingDragging Vertical placement InstallationInstallation area Using two feet Mount the feet on the PC unit Using one footMount the disassembled foot on the PC unit Disassemble the feet Horizontal placementPlace the PC unit on the disassembled feet Vertical placement Example of installationHorizontal placement Connection Connect the power cable to the display Connect the power cable to the outletConnect the mouse Connect the LAN cable Connect the keyboardConnect the display cable to the PC unit Connect the LAN cable to the network Connecting the power cable Page Turning On the Power Press the power switch on the display Turning on the powerPress the power switch on the PC Turning off the power Turning Off the Power SupplyWindows Me Windows Windows 98/95Windows NT Restarting Restarting the PC Point CD-ROM Removing the CD Inserting or removing a CDInserting a CD Press the Eject button Inserting or removing a floppy disk Point Floppy DiskInserting a floppy disk Confirm that the Floppy disk access lamp is off Removing the floppy disk Hardware Before Installing a Peripheral Device Page Removing the upper cover Removing the CoverRemove the upper cover Removing the reinforcement bracket Installing Memory Modules Location of memory modules Memory module installation procedureApplicable memory modules Installing Memory Modules Memory module combinations Insert a memory module into the slot Installing an Expansion Card Location of expansion cards Applicable expansion cards Installing an Expansion Card Remove the slot cover Plug the PC Turn on the PC Windows Me/98/95/2000 models Install the mounting bracketInsert the expansion card into the slot Windows NT models Installing an Internal Option Location of internal optionsPage Installing an Internal Hard Disk Drive Installing a device in the 3.5-inch front access bay Installing Other Internal Options Make a setting on the option to be installed Install the internal option on the PC unit Connect the flat cable Master Slave Connect the power cable Troubleshooting Problems Mouse cursor does not move Characters entered using the keyboard are not displayedData cannot be read from the CD-ROM drive Windows Me/98/95 Technical Information Maintenance of the keyboard Maintenance of the HardwareMaintenance of the PC unit Cleaning CDs Maintenance of the mouse Cleaning the floppy disk drive Preventing Television or Radio Interference Additional CautionsUSB Windows Me/98/95/2000 models Wakeup On LAN USB keyboard Windows 98 modelsAddition of a LAN card Digital display output Video memory capacity display Power-saving function of displayConnecting the display Replacing the display Mouse with a scrolling function scrolling wheel Power-saving functionInternational EnergyStar Program Intel processor serial number PC unit specifications Hardware SpecificationsProduct name LAN adapter specifications CSMA/CD Graphical specifications Sound specificationsConnector specifications TXC+ LAN connector 100BASE-TX/10BASE-T Mouse connector Keyboard connector Index CD-ROM drive Mouse Clicking