Position | Fujitsu 600C specs

Configuration II: the number of devices attached to the SCSI bus (including the host PC) is three. The scanner is located at the end of the connection, as shown below.

Host PC

SCSI device

Scanner



						Set terminator switch at “on”
						Set terminator switch at “on”
Terminator							position
Terminator

If there is already another device linked to the host via SCSI cable, remove the terminator from that device. If the terminator can not be removed, it is recommended that the connection of Configuration I be used.

1.Set scanner’s SCSI terminator switch on

2.Plug one end of the SCSI cable to one female connector of the previous device or the host.

SCSI specifications require that:

1.Only one terminator may be attached to each end of the daisy chain.

2.The total length of the daisy chain must not exceed 6 meters. The vendor suggests that the SCSI cable be two or three meters in length to allow other devices to be attached to the SCSI bus.

3.Each device on the chain will be assigned a different ID. Devices with the same SCSI ID will cause them to malfunction.

4.There is no restriction on the position of the devices on the daisy chain.

3-6

Image 18

Fujitsu 600C manual Position

Contents

Version Page Table of Contents Diagnostics Group 3 error flowchart no paper in ADF paper tray Page General General System Block Diagram Device Configuration Outer View Components Functional Specifications Functional Specifications Remarks Environmental Specifications Environmental Specifications Remarks Operation Removing the Shipping Bracket Remove the shipping retainer Fasten the shipping retainer Power On/Off Indication Panel Scsi ID setting Setting the Scsi ID and Connecting the Interface CableNames and functions of the indicators Name Color Function Scsi Cable Connection Position Paper conditions Paper SpecificationsPaper Size 2.1 ADF FIatbed Items to avoid Readable area ADF readable area Document Setting Method When the document size is of letter/A4 size or smallerFlatbed When the document is a thick book Setting the ADF paper chute2 ADF Placing the documents on the ADF paper chute Placing the document on the ADF paper chute Angling the document sheets Separating the sheets for easy feeding Cleaning Cleaning the document cover and the document glass Cleaning inside the ADF Page Interface ∙ Busy ∙ Check Condition ∙ Good ∙ Reservation Conflict Physical Specifications Connection 1SCSI physical specifications Physical SpecificationSpecifications Termination Signal Name Pin Number Pin assignments Scsi Bus System configurationSystem configuration Addresses of Scsi devices Bus signals 2Bus signals Bus signal drive conditions 3Bus phases vs. signal drive sources 1/2 Bus Phases Method of driving the interface signalOr connection Nonor connection 5Signal delay times definition Time Definition BUS Free phase Signal delay times definitionTime Definition Arbitration phase BSY Scsi SEL Selection phase Information Transfer phases Information Transfer phase type PhaseDB7 to 9,P Transfer Direction Asynchronous information transfer Asynchronous transfer from target to initiator Asynchronous transler from initiator to target Commands Relative addressing is not supportedControl byte is not supported Operation Command Code hex Description Reserve Unit commandCommands Bit and field described as Reserved are Reserve Unit command Command phase initiator Õ target TP third party ByteTpid third party device ID Byte Release Unit command Release Unit command Command phase initiator → targetTP third party Byte 10 Inquiry command Inquiry commandInquiry command Command phase initiator → target Step Bus phase Initiator operation Target operation Evpd enable vital product data Byte Code ByteCAllocation length Byte Inquiry data Data in phase target → initiator Aenc Color mode Byte 24, bit 6 to SftRst Soft Reset ByteADF mode Byte 24, bit ISO version, Ecma version, Ansi approved version Byte Request Sense command Request Sense command Command phase initiator → target11 Request Sense command Allocation length Byte Sense data Data EN phase target → initiatorError code Byte Valid Byte EOM end of medium Byte ILI incorrect length indicator ByteFM file mark Byte Sense key Byte Sense Additional Description Send Diagnostic commandCommand-specific information bytes Bytes 8 to B Sense code Send Diagnostic command Command phase initiator → target PF page format ByteSlftst selftest Byte Test Unit Ready command Contents of self-testResults of self-test Test Unit Ready command Command phase initiator → target Acknowledgment SET Window command SET Window command Command phase initiator → target Window date Data OUT phase initiator → target Transfer Length Bytes 6 toHeader Window descriptor block Auto Byte Y resolution XR, YR Bytes 2 to 3 and 4 toWindow identifier Byte Upper left X,YULX, ULY Bytes 6 to 9, a to D Brightness Byte Remarks Bit ordering Bytes 1E to 1F Bit per pixel Byte 1ARIF reverse image format Byte 1D, bit Halftone pattern Bytes lB to 1C lB reserved Compression type, argument Bytes 20 to Update of ScanPartner 600C OEM manual7.4 B&W Scanning Vender unique parameters 18 Vender unique parameters byte 28 and laterPage ADF Byte 2A, Bit Color Scanning Vender unique parameters19 Vendor unique parameters byte 28 and later Source Byte 2A, Bit Line width Byte 2D to 2E Highlight value Byte 2BShadow value Byte 2C Line count Byte 2F to Object Position command Object Position command Command phase initator → target Position type ByteBit Count Bytes 2 to Unload objectLoad object Normal Read command Step Bus phase Initiator operation Target operationADF sequence Data type qualifier Bytes 4 to Read command Command phase initiator → targetData type code Byte Transfer length TL Bytes 6 to For binary data Data in phase target → initiatorImage data Data Type Code = Pixel size data Data Type Code = Scan command Scan Command phase initiator → target Status Status phase target initiator Code Status of unit Phase ATN detection timing MessagesATN detection Command Complete X00 Message in phase target → initiator Message typesMessage Abort X06 Message OUT phase initiator → target Message Reject X07 Message IN/OUT phase initiator → targetATN detection phase Action Phase when ATN is detected Action No Operation X08 Message OUT phase initiator → targetBUS Device Reset X0C Message OUT phase initiator → target Message rejected Action Idendify X80 to XFF Message OUT phase initiator → target Command Sequence Initial sequence Read sequence Read command sequenceRead sequence for B&W mode Single Read Multiple Read Status Transition of Logical Unit Error Table Sense key Items for Specifying Window Page Online diagnostics Ready LED Paper Jam LED Error indicationOnline diagnostics Offline diagnostics Offline diagnostics results Diagnostic flowcharts Group 1 error flowchart Lamp assemblyGroup 2 error flowchart Flatbed/ADF motor Group 3 error flowchart paper in ADF paper tray Group 3 error flowchart no paper in ADF paper tray