FIatbed, Items to avoid | Fujitsu 600C manual

3.5.2.2FIatbed

(a)Paper quality No condition

(b)Ream weight No condition

(C)Paper form

Square is preferred.

3.5.2.3Items to avoid

Paper such as the following cannot be fed by ADF.

(a)Paper with clips or staples.

(b)Paper with ink not dry.

(C)Paper with inconsistent thickness, such as an envelope.

(d)Paper with large rumples or curls. (e)Paper with folds or tears.

(f)Tracing paper.

(g)Coating paper.

(h)Carbonless paper.

(i)Paper smaller than A5 size or larger than A4 width.

(j)Items other than paper, such as clothes, metal sheet, or OHP film.

(k)Photographic paper.

(1)Paper that has notches on its side. (m)Paper that has a shape other than square.

(n) Very thin paper.

(o) Important document not to be damaged.

Use the flatbed to perform scanning when reading paper of items e to o.

3-8

Image 20

Fujitsu 600C manual FIatbed, Items to avoid

Contents

Version Page Table of Contents Diagnostics Group 3 error flowchart no paper in ADF paper tray Page General General System Block Diagram Device Configuration Outer View Components Functional Specifications Functional Specifications Remarks Environmental Specifications Environmental Specifications Remarks Operation Removing the Shipping Bracket Remove the shipping retainer Fasten the shipping retainer Power On/Off Indication Panel Setting the Scsi ID and Connecting the Interface Cable Names and functions of the indicatorsScsi ID setting Name Color Function Scsi Cable Connection Position Paper Specifications Paper SizePaper conditions 2.1 ADF FIatbed Items to avoid Readable area ADF readable area Flatbed Document Setting MethodWhen the document size is of letter/A4 size or smaller 2 ADF When the document is a thick bookSetting the ADF paper chute Placing the documents on the ADF paper chute Placing the document on the ADF paper chute Angling the document sheets Separating the sheets for easy feeding Cleaning Cleaning the document cover and the document glass Cleaning inside the ADF Page Interface ∙ Busy ∙ Check Condition ∙ Good ∙ Reservation Conflict Physical Specifications Connection Physical Specification Specifications1SCSI physical specifications Termination Signal Name Pin Number Pin assignments System configuration System configurationScsi Bus Addresses of Scsi devices Bus signals 2Bus signals Bus signal drive conditions 3Bus phases vs. signal drive sources 1/2 Or connection Nonor connection Bus PhasesMethod of driving the interface signal 5Signal delay times definition Time Definition Time Definition BUS Free phaseSignal delay times definition Arbitration phase BSY Scsi SEL Selection phase DB7 to 9,P Transfer Direction Information Transfer phasesInformation Transfer phase type Phase Asynchronous information transfer Asynchronous transfer from target to initiator Asynchronous transler from initiator to target Control byte is not supported CommandsRelative addressing is not supported Reserve Unit command CommandsOperation Command Code hex Description Bit and field described as Reserved are Tpid third party device ID Byte Reserve Unit command Command phase initiator Õ targetTP third party Byte TP third party Byte Release Unit commandRelease Unit command Command phase initiator → target Inquiry command Inquiry command Command phase initiator → target10 Inquiry command Step Bus phase Initiator operation Target operation CAllocation length Byte Evpd enable vital product data ByteCode Byte Inquiry data Data in phase target → initiator Aenc SftRst Soft Reset Byte ADF mode Byte 24, bitColor mode Byte 24, bit 6 to ISO version, Ecma version, Ansi approved version Byte 11 Request Sense command Request Sense commandRequest Sense command Command phase initiator → target Sense data Data EN phase target → initiator Error code ByteAllocation length Byte Valid Byte ILI incorrect length indicator Byte FM file mark ByteEOM end of medium Byte Sense key Byte Send Diagnostic command Command-specific information bytes Bytes 8 to BSense Additional Description Sense code Slftst selftest Byte Send Diagnostic command Command phase initiator → targetPF page format Byte Results of self-test Test Unit Ready commandContents of self-test Test Unit Ready command Command phase initiator → target Acknowledgment SET Window command SET Window command Command phase initiator → target Header Window date Data OUT phase initiator → targetTransfer Length Bytes 6 to Window descriptor block Y resolution XR, YR Bytes 2 to 3 and 4 to Window identifier ByteAuto Byte Upper left X,YULX, ULY Bytes 6 to 9, a to D Brightness Byte Remarks Bit per pixel Byte 1A RIF reverse image format Byte 1D, bitBit ordering Bytes 1E to 1F Halftone pattern Bytes lB to 1C lB reserved Update of ScanPartner 600C OEM manual 7.4 B&W Scanning Vender unique parametersCompression type, argument Bytes 20 to 18 Vender unique parameters byte 28 and laterPage Color Scanning Vender unique parameters 19 Vendor unique parameters byte 28 and laterADF Byte 2A, Bit Source Byte 2A, Bit Highlight value Byte 2B Shadow value Byte 2CLine width Byte 2D to 2E Line count Byte 2F to Object Position command Bit Object Position command Command phase initator → targetPosition type Byte Unload object Load objectCount Bytes 2 to Normal ADF sequence Read commandStep Bus phase Initiator operation Target operation Read command Command phase initiator → target Data type code ByteData type qualifier Bytes 4 to Transfer length TL Bytes 6 to Data in phase target → initiator Image data Data Type Code =For binary data Pixel size data Data Type Code = Scan command Scan Command phase initiator → target Status Status phase target initiator Code Status of unit ATN detection Phase ATN detection timingMessages Message Command Complete X00 Message in phase target → initiatorMessage types ATN detection phase Action Abort X06 Message OUT phase initiator → targetMessage Reject X07 Message IN/OUT phase initiator → target No Operation X08 Message OUT phase initiator → target BUS Device Reset X0C Message OUT phase initiator → targetPhase when ATN is detected Action Message rejected Action Idendify X80 to XFF Message OUT phase initiator → target Command Sequence Initial sequence Read command sequence Read sequence for B&W modeRead sequence Single Read Multiple Read Status Transition of Logical Unit Error Table Sense key Items for Specifying Window Page Online diagnostics Online diagnosticsReady LED Paper Jam LED Error indication Offline diagnostics Offline diagnostics results Group 2 error flowchart Flatbed/ADF motor Diagnostic flowchartsGroup 1 error flowchart Lamp assembly Group 3 error flowchart paper in ADF paper tray Group 3 error flowchart no paper in ADF paper tray