Color Scanning Vender unique parameters | Fujitsu 600C guide

4.4.7.5Color Scanning Vender unique parameters

Table 4-19 Vendor unique parameters (byte 28 and later)

28

29

2A

2B

2C

2D

2E

2F

30

31

32

7	6			5	4	3			2	1		0
				Vender unique			identification		code
					Parameter length
ADF source					Color						Reserved

Highlight value

Shadow value

Line width

Line count

Reserved

Reserved

4.4.7.5.1Vendor unique identification code: Byte 28

Specifies a vendor unique identification code. For color image scanning, X'FF' must be specified. If other value is specified, this scanner returns the following error:

Status: B'00001' (CHECK CONDITION)

Sense key: X'5' (ILLEGAL REQUEST)

4.4.7.5.2Parameter length: Byte 29

Specifies parameter length for color scan.

4.4.7.5.3Color scanning parameters

a)ADF: Byte 2A, Bit 7

0:Flatbed scan mode

1:ADF scan mode

b)Source: Byte 2A, Bit 6

0:The initiator could read the line width and line count of the current scan page by using "READ" command. When the bits is specified X'00', the data field of Line width (X'2D' to X'2E') and Line

count (X'2F') to X'30') will be ignored by the scanner.

1: The initiator can tell the scanner the line width and the line count for the current page. The

information

should be placed in Line width (X'2D' to X'2E') and Line count (X'2E' to X'30').

c)Color: Byte 2A, Bit 5 to 3

Specifies a color pass. 000: Green channel

001:Red channel

010:Green channel

011:Blue channel

100:R-G-B color image

4-41

Image 69

Fujitsu 600C manual Color Scanning Vender unique parameters, Vendor unique parameters byte 28 and later, ADF Byte 2A, Bit

Contents

Version Page Table of Contents Diagnostics Group 3 error flowchart no paper in ADF paper tray Page General General System Block Diagram Outer View Device Configuration Components Functional Specifications Remarks Functional Specifications Environmental Specifications Remarks Environmental Specifications Removing the Shipping Bracket Operation Remove the shipping retainer Fasten the shipping retainer Indication Panel Power On/Off Names and functions of the indicators Setting the Scsi ID and Connecting the Interface CableScsi ID setting Name Color Function Scsi Cable Connection Position Paper Size Paper SpecificationsPaper conditions 2.1 ADF Items to avoid FIatbed ADF readable area Readable area Document Setting Method When the document size is of letter/A4 size or smallerFlatbed When the document is a thick book Setting the ADF paper chute2 ADF Placing the document on the ADF paper chute Placing the documents on the ADF paper chute Separating the sheets for easy feeding Angling the document sheets Cleaning the document cover and the document glass Cleaning Cleaning inside the ADF Page Interface ∙ Busy ∙ Check Condition ∙ Good ∙ Reservation Conflict Connection Physical Specifications Specifications Physical Specification1SCSI physical specifications Termination Pin assignments Signal Name Pin Number System configuration System configurationScsi Bus Addresses of Scsi devices 2Bus signals Bus signals 3Bus phases vs. signal drive sources 1/2 Bus signal drive conditions Bus Phases Method of driving the interface signalOr connection Nonor connection 5Signal delay times definition Time Definition BUS Free phase Signal delay times definitionTime Definition Arbitration phase BSY Scsi SEL Selection phase Information Transfer phases Information Transfer phase type PhaseDB7 to 9,P Transfer Direction Asynchronous transfer from target to initiator Asynchronous information transfer Asynchronous transler from initiator to target Commands Relative addressing is not supportedControl byte is not supported Commands Reserve Unit commandOperation Command Code hex Description Bit and field described as Reserved are Reserve Unit command Command phase initiator Õ target TP third party ByteTpid third party device ID Byte Release Unit command Release Unit command Command phase initiator → targetTP third party Byte Inquiry command Command phase initiator → target Inquiry command10 Inquiry command Step Bus phase Initiator operation Target operation Evpd enable vital product data Byte Code ByteCAllocation length Byte Aenc Inquiry data Data in phase target → initiator ADF mode Byte 24, bit SftRst Soft Reset ByteColor mode Byte 24, bit 6 to ISO version, Ecma version, Ansi approved version Byte Request Sense command Request Sense command Command phase initiator → target11 Request Sense command Error code Byte Sense data Data EN phase target → initiatorAllocation length Byte Valid Byte FM file mark Byte ILI incorrect length indicator ByteEOM end of medium Byte Sense key Byte Command-specific information bytes Bytes 8 to B Send Diagnostic commandSense Additional Description Sense code Send Diagnostic command Command phase initiator → target PF page format ByteSlftst selftest Byte Test Unit Ready command Contents of self-testResults of self-test Acknowledgment Test Unit Ready command Command phase initiator → target SET Window command Command phase initiator → target SET Window command Window date Data OUT phase initiator → target Transfer Length Bytes 6 toHeader Window descriptor block Window identifier Byte Y resolution XR, YR Bytes 2 to 3 and 4 toAuto Byte Upper left X,YULX, ULY Bytes 6 to 9, a to D Remarks Brightness Byte RIF reverse image format Byte 1D, bit Bit per pixel Byte 1ABit ordering Bytes 1E to 1F Halftone pattern Bytes lB to 1C lB reserved 7.4 B&W Scanning Vender unique parameters Update of ScanPartner 600C OEM manualCompression type, argument Bytes 20 to 18 Vender unique parameters byte 28 and laterPage 19 Vendor unique parameters byte 28 and later Color Scanning Vender unique parametersADF Byte 2A, Bit Source Byte 2A, Bit Shadow value Byte 2C Highlight value Byte 2BLine width Byte 2D to 2E Line count Byte 2F to Object Position command Object Position command Command phase initator → target Position type ByteBit Load object Unload objectCount Bytes 2 to Normal Read command Step Bus phase Initiator operation Target operationADF sequence Data type code Byte Read command Command phase initiator → targetData type qualifier Bytes 4 to Transfer length TL Bytes 6 to Image data Data Type Code = Data in phase target → initiatorFor binary data Pixel size data Data Type Code = Scan Command phase initiator → target Scan command Code Status of unit Status Status phase target initiator Phase ATN detection timing MessagesATN detection Command Complete X00 Message in phase target → initiator Message typesMessage Abort X06 Message OUT phase initiator → target Message Reject X07 Message IN/OUT phase initiator → targetATN detection phase Action BUS Device Reset X0C Message OUT phase initiator → target No Operation X08 Message OUT phase initiator → targetPhase when ATN is detected Action Message rejected Action Idendify X80 to XFF Message OUT phase initiator → target Initial sequence Command Sequence Read sequence for B&W mode Read command sequenceRead sequence Single Read Multiple Read Status Transition of Logical Unit Sense key Error Table Items for Specifying Window Page Online diagnostics Ready LED Paper Jam LED Error indicationOnline diagnostics Offline diagnostics results Offline diagnostics Diagnostic flowcharts Group 1 error flowchart Lamp assemblyGroup 2 error flowchart Flatbed/ADF motor Group 3 error flowchart paper in ADF paper tray Group 3 error flowchart no paper in ADF paper tray