Manuals / Fujitsu / Computer Equipment / Scanner

Fujitsu 600C manual Status STATUS phase target initiator, Code, Status of unit

Models: 600C

1 95

Download 95 pages 10.46 Kb

Page 78

4.5 Status: STATUS phase (target ® initiator)

Byte 0 1 2 3 4 5

7	6	5	4	3	2	1	0
			Operator code X'1B'

(Reserved)

Transfer length

Control byte

Transfer length: X'01'

The transfer length specifies the length in byte of the window identifier list that should be sent in the DATA OUT phase.

Window identifier: X'00'

4.5 Status: STATUS phase (target ® initiator)

Each time a command is terminated, the target moves into the STATUS phase and returns a status byte to the initiator to report the completion of the command.

Status byte

7	6	5	4	3	2	1	0
(Reserved)				Status byte code			(Reserved)

The status supported by this scanner are summarized in the following table.

	Table 4-22

Code	Status of unit

000000	GOOD
	∙ The command has successfully terminated
000001	CHECK CONDITION
	a) The command has abnormally terminated.
	b) An abnormal condition was detected before a unit is selected.
	∙ The target detected an error before start of command-
	controlled processing.
	∙ A unit that switched from the NOT READY status to the
	READY status was selected for the first time.
	∙ A unit that received a RESE~ CONDITION or a BUS
	DEVICE RESET message was selected for the first time.

4-50

Image 78

Fujitsu 600C manual Status STATUS phase target initiator, Code, Status of unit

Contents

Fujitsu ScanPartner 600C OEM Manual Fujitsu IncVersion Page 1. GENERAL Table of Contents2. SPECIFICATIONS 3. OPERATION5. DIAGNOSTICS 5.3.4 Group 3 error flowchart no paper in ADF paper tray Page 1. General 1.1 GeneralFigure 1-1 System Block Diagram 1.2 Device Configuration 1.2.1 Outer ViewFigure 1-2 ScanPartner 600C Outer View 1.2.2 Components 2.1 Functional Specifications 2.2 Environmental Specifications 2. Specifications2.1 Functional Specifications Table 2-1 Functional SpecificationsSpecifications Environmental SpecificationsTable 2-2 Environmental Specifications Remarks3. OPERATION 3.1 Removing the Shipping Bracket1. Remove the shipping retainer 2. Fasten the shipping retainer Figure 3-1 Power Switch 3.2 Power On/Off3.3 Indication Panel Figure 3-2 Indication PanelFigure 3-3 Signal cable connection 3.4 Setting the SCSI ID and Connecting the Interface CableTable 3-1 Names and functions of the indicators Content3.4.1 SCSI Cable Connection Host PC 3.5.2 Paper conditions 3.5 Paper Specifications3.5.1 Paper Size Figure 3-4 Paper size specifications3.5.2.2 FIatbed 3.5.2.3 Items to avoid3.5.3 Readable area Figure 3-5 ADF readable area3.6.1.1 When the document size is of letter/A4 size or smaller 3.6 Document Setting Method3.6.1 Flatbed Figure 3-6 Flatbed reading3.6.2.1 Setting the ADF paper chute 3.6.2 ADF3.6.1.2 When the document is a thick book Figure 3-7 Setting the ADF paper chute3.6.2.2 Placing the documents on the ADF paper chute Figure 3-8 Placing the document on the ADF paper chutea Angling the document sheets b Separating the sheets for easy feeding3.7 Cleaning 3.7.1 Cleaning the document cover and the document glass3.7.2 Cleaning inside the ADF Page 4.5 Status STATUS phase target initiator 4.6 Messages 4. INTERFACE4.1 Physical Specifications 4.2 SCSI Bus 4.3 Bus Phases 4.4 Commands 4.7 Command Sequence 4.8 Status Transition of Logical Unit3. Commands The following commands are supported by this scanner 4.1 Physical Specifications 4.1.1 ConnectionSpecifications 4.1.2 Physical Specification4.1.3 Termination Table 4-1 SCSI physical specificationsSignal Name 4.1.4 Pin assignmentsSignal Name Pin Number4.2.1.1 System configuration 4.2.1 System configuration4.2 SCSI Bus 4.2.1.2 Addresses of SCSI devices4.2.2 Bus signals Table 4-2 Bus signals4.2.3 Bus signal drive conditions Table 4-3 Bus phases vs. signal drive sources 1/24.3 Bus Phases Table 4-4 Method of driving the interface signalFigure 4-2 Phase sequence Definition Table 4-5 Signal delay times definitionTime AssertionTime 4.3.1 BUS FREE phaseTable 4.5 Signal delay times definition definition4.3.2 ARBITRATION phase others4-12 Page 4.3.3 SELECTION phase Phase 4.3.4 INFORMATION TRANSFER phasesTable 4-6 INFORMATION TRANSFER phase type DB7 to 9,P4.3.4.1 Asynchronous information transfer a Asynchronous transfer from target to initiatorb Asynchronous transler from initiator to target 4.4 Commands b Relative addressing is not supportedCommand 4.4.1 RESERVE UNIT commandTable 4-7 Commands d A bit and field described as Reserved are4.4.1.1 RESERVE UNIT command COMMAND phase initiator Õ target a TP third party Byteb TPID third party device ID Byte 4.4.2 RELEASE UNIT command 4.4.2.1 RELEASE UNIT command COMMAND phase initiator → targetTable 4-10 INQUIRY command 4.4.3 INQUIRY command4.4.3.1 INQUIRY command COMMAND phase initiator → target Bus phaseCAllocation length Byte a EVPD enable vital product data Byteb Page code Byte EVPD4.4.3.2 Inquiry data DATA IN phase target → initiator f Asynchronous event notification capability AENC Byte l sftRst Soft Reset Bytee ISO version, ECMA version, ANSI approved version Byte g Response data format ByteTable 4-11 REQUEST SENSE command 4.4.4 REQUEST SENSE command4.4.4.1 REQUEST SENSE command COMMAND phase initiator → target Bus phasea Allocation length Byte 4.4.4.2 Sense data DATA EN phase target → initiatorb Error code Byte a Valid Bytee EOM end of medium Byte f ILI incorrect length indicator Byted FM file mark Byte g Sense key ByteTable 4-14 SEND DIAGNOSTIC command 4.4.5 SEND DIAGNOSTIC commandj Command-specific information bytes Bytes 8 to B Bus phaseBus phase 4.4.5.1 SEND DIAGNOSTIC command COMMAND phase initiator → targetTable 4.14 SEND DIAGNOSTIC command StepBus phase 4.4.6 TEST UNIT READY command4.4.5.2 Contents of self-test 4.4.5.3 Results of self-testByte 4.4.6.1 TEST UNIT READY command COMMAND phase initiator → target4.4.6.2 Acknowledgment Operation codeTable 4-16 SET WINDOW command 4.4.7 SET WINDOW command4.4.7.1 SET WINDOW command COMMAND phase initiator → target Bus phase4.4.7.2 Window date DATA OUT phase initiator → target a TRANSFER LENGTH Bytes 6 toa Header b Window descriptor block d Auto Byte e X, Y resolution XR, YR Bytes 2 to 3 and 4 toc Window identifier Byte f Upper left X,YULX, ULY Bytes 6 to 9, A to DValues under 0 in are omitted h Brightness ByteRemarks p Bit ordering Bytes 1E to 1F I Bit per pixel Byte 1An RIF reverse image format Byte 1D, bit m Halftone pattern Bytes lB to 1C lB reservedq Compression type, argument Bytes 20 to 4.4.7.3 Update of ScanPartner 600C OEM manual4.4.7.4 B&W Scanning Vender unique parameters Table 4-18 Vender unique parameters byte 28 and later4.4.7.4.2 Paper size byte 4.4.7.4.1 Vendor unique identification code ByteStatus B00001 CHECK CONDITION Sense Key X05 ILLEGAL REQUEST Specified a Paper Size. Set paper size used only in ADF modea ADF Byte 2A, Bit 4.4.7.5 Color Scanning Vender unique parametersTable 4-19 Vendor unique parameters byte 28 and later b Source Byte 2A, Bitf Line width Byte 2D to 2E d Highlight value Byte 2Be Shadow value Byte 2C Specifies line width in bytes for the current scan page4.4.8 OBJECT POSITION command POSITION TYPE 4.4.8.1 OBJECT POSITION command COMMAND phase initator → targeta Position type Byte Position typec Load object 4.4.8.2 Acknowledgmentb Unload object d Count Bytes 2 to4.4.8.3 ADF sequence 4.4.9 READ commandBus phase Stepb Data type qualifier Bytes 4 to 4.4.9.1 READ command COMMAND phase initiator → targeta Data type code Byte c Transfer length TL Bytes 6 tob For binary data 4.4.9.2 DATA IN phase target → initiatora Image data DATA TYPE CODE = C Pixel size data DATA TYPE CODE =Bus phase 4.4.10 Scan command4.4.10.1 SCAN Command phase initiator → target Step4.5 Status STATUS phase target initiator CodeStatus of unit Phase 4.6 Messages4.6.1 ATN detection Status of unit4.6.2 Message types 4.6.2.1 COMMAND COMPLETE X00 MESSAGE IN phase target → initiatorATN detection phase 4.6.2.3 ABORT X06 MESSAGE OUT phase initiator → target4.6.2.4 MESSAGE REJECT X07 MESSAGE IN/OUT phase initiator → target Action4.6.2.7 BUS DEVICE RESET X0C MESSAGE OUT phase initiator → target 4.6.2.5 NO OPERATION X08 MESSAGE OUT phase initiator → target4.6.2.6 MESSAGE PARITY ERROR X09 MESSAGE OUT phase initiator → target Phase when ATN is detected4.6.2.8 IDENDIFY X80 TO XFF MESSAGE OUT phase initiator → target 4.7 Command Sequence 4.7.1 Initial sequence4.7.2.1 Read sequence for B&W mode 4.7.3 READ command sequence4.7.2 Read sequence 4.7.3.1 Single READ4.7.3.2 Multiple READ 4.8 Status Transition of Logical Unit HARD 4.9 Error TableERROR ILLEGALcomposition 4.10 Items for Specifying WindowImage BinaryPage 5.1 Online Diagnostics 5.2 Offline Diagnostics 5. Diagnostics5.1 Online diagnostics 5.3 Diagnostic FlowchartsTable 5-2 Offline diagnostics results 5.2 Offline diagnosticsError indication Ready LED5.3 Diagnostic flowcharts 5.3.1 Group 1 error flowchart Lamp assembly5.3.2 Group 2 error flowchart Flatbed/ADF motor 5.3.3 Group 3 error flowchart paper in ADF paper tray 5.3.4 Group 3 error flowchart no paper in ADF paper tray ADF paper-out