Manuals / Fujitsu / Computer Equipment / Scanner

Fujitsu 600C manual Window date DATA OUT phase initiator → target, a TRANSFER LENGTH Bytes 6 to

Models: 600C

1 95

Download 95 pages 10.46 Kb

Page 62

(a) TRANSFER LENGTH: Bytes 6 to 8

Byte 0

1

2

⏐

5

6

7

8

9

7	6					5	4	3		2		1		0
							Operator code X'24'

	Logical unit number										(Reserved)

(Reserved)

(MSB)

Transfer length

(LSB)

Control byte

(a) TRANSFER LENGTH: Bytes 6 to 8

Specifies the number of window data bytes sent in the DATA OUT phase. A 0 means that no data transferred; this situation is not considered an error.

If the number of bytes is not enough (less than 48) to set a single window, the scanner returns the following error

Status: B'00001' (CHECK CONDITION) Sense key: X'5' (ILLEGAL REQUEST)

Sense key: X'5' (ILLEGAL REQUEST)

4.4.7.2Window date: DATA OUT phase (initiator → target)

Window data specifies the details of a window. Window data contains a bead and one or more window descriptor block. Each window descriptor block specifies the attributes of a window (size, position, sca etc.).

If a target receives the SET WINDOW command when it already has window data, ..the target discards a current window data and validates the newly received data.

(a)Header

Window data (header) is shown in the following illustration.

Byte 0

7

6

5

4

3

2

1

0

⏐

5

6

7

(MSB)

Reserved

Window descriptor block length

(LSB)

Window descriptor block length: Bytes 6 and 7

4-34

Image 62

Fujitsu 600C manual Window date DATA OUT phase initiator → target, a TRANSFER LENGTH Bytes 6 to, a Header

Contents

Version Fujitsu ScanPartner 600C OEM ManualFujitsu Inc Page 1. GENERAL Table of Contents2. SPECIFICATIONS 3. OPERATION5. DIAGNOSTICS 5.3.4 Group 3 error flowchart no paper in ADF paper tray Page 1. General 1.1 GeneralFigure 1-1 System Block Diagram Figure 1-2 ScanPartner 600C Outer View 1.2 Device Configuration1.2.1 Outer View 1.2.2 Components 2.1 Functional Specifications 2.2 Environmental Specifications 2. Specifications2.1 Functional Specifications Table 2-1 Functional SpecificationsSpecifications Environmental SpecificationsTable 2-2 Environmental Specifications Remarks3. OPERATION 3.1 Removing the Shipping Bracket1. Remove the shipping retainer 2. Fasten the shipping retainer Figure 3-1 Power Switch 3.2 Power On/Off3.3 Indication Panel Figure 3-2 Indication PanelFigure 3-3 Signal cable connection 3.4 Setting the SCSI ID and Connecting the Interface CableTable 3-1 Names and functions of the indicators Content3.4.1 SCSI Cable Connection Host PC 3.5.2 Paper conditions 3.5 Paper Specifications3.5.1 Paper Size Figure 3-4 Paper size specifications3.5.2.2 FIatbed 3.5.2.3 Items to avoid3.5.3 Readable area Figure 3-5 ADF readable area3.6.1.1 When the document size is of letter/A4 size or smaller 3.6 Document Setting Method3.6.1 Flatbed Figure 3-6 Flatbed reading3.6.2.1 Setting the ADF paper chute 3.6.2 ADF3.6.1.2 When the document is a thick book Figure 3-7 Setting the ADF paper chute3.6.2.2 Placing the documents on the ADF paper chute Figure 3-8 Placing the document on the ADF paper chutea Angling the document sheets b Separating the sheets for easy feeding3.7 Cleaning 3.7.1 Cleaning the document cover and the document glass3.7.2 Cleaning inside the ADF Page 4.5 Status STATUS phase target initiator 4.6 Messages 4. INTERFACE4.1 Physical Specifications 4.2 SCSI Bus 4.3 Bus Phases 4.4 Commands 4.7 Command Sequence 4.8 Status Transition of Logical Unit3. Commands The following commands are supported by this scanner 4.1 Physical Specifications 4.1.1 ConnectionSpecifications 4.1.2 Physical Specification4.1.3 Termination Table 4-1 SCSI physical specificationsSignal Name 4.1.4 Pin assignmentsSignal Name Pin Number4.2.1.1 System configuration 4.2.1 System configuration4.2 SCSI Bus 4.2.1.2 Addresses of SCSI devices4.2.2 Bus signals Table 4-2 Bus signals4.2.3 Bus signal drive conditions Table 4-3 Bus phases vs. signal drive sources 1/2Figure 4-2 Phase sequence 4.3 Bus PhasesTable 4-4 Method of driving the interface signal Definition Table 4-5 Signal delay times definitionTime AssertionTime 4.3.1 BUS FREE phaseTable 4.5 Signal delay times definition definition4-12 4.3.2 ARBITRATION phaseothers Page 4.3.3 SELECTION phase Phase 4.3.4 INFORMATION TRANSFER phasesTable 4-6 INFORMATION TRANSFER phase type DB7 to 9,P4.3.4.1 Asynchronous information transfer a Asynchronous transfer from target to initiatorb Asynchronous transler from initiator to target 4.4 Commands b Relative addressing is not supportedCommand 4.4.1 RESERVE UNIT commandTable 4-7 Commands d A bit and field described as Reserved areb TPID third party device ID Byte 4.4.1.1 RESERVE UNIT command COMMAND phase initiator Õ targeta TP third party Byte 4.4.2 RELEASE UNIT command 4.4.2.1 RELEASE UNIT command COMMAND phase initiator → targetTable 4-10 INQUIRY command 4.4.3 INQUIRY command4.4.3.1 INQUIRY command COMMAND phase initiator → target Bus phaseCAllocation length Byte a EVPD enable vital product data Byteb Page code Byte EVPD4.4.3.2 Inquiry data DATA IN phase target → initiator f Asynchronous event notification capability AENC Byte l sftRst Soft Reset Bytee ISO version, ECMA version, ANSI approved version Byte g Response data format ByteTable 4-11 REQUEST SENSE command 4.4.4 REQUEST SENSE command4.4.4.1 REQUEST SENSE command COMMAND phase initiator → target Bus phasea Allocation length Byte 4.4.4.2 Sense data DATA EN phase target → initiatorb Error code Byte a Valid Bytee EOM end of medium Byte f ILI incorrect length indicator Byted FM file mark Byte g Sense key ByteTable 4-14 SEND DIAGNOSTIC command 4.4.5 SEND DIAGNOSTIC commandj Command-specific information bytes Bytes 8 to B Bus phaseBus phase 4.4.5.1 SEND DIAGNOSTIC command COMMAND phase initiator → targetTable 4.14 SEND DIAGNOSTIC command StepBus phase 4.4.6 TEST UNIT READY command4.4.5.2 Contents of self-test 4.4.5.3 Results of self-testByte 4.4.6.1 TEST UNIT READY command COMMAND phase initiator → target4.4.6.2 Acknowledgment Operation codeTable 4-16 SET WINDOW command 4.4.7 SET WINDOW command4.4.7.1 SET WINDOW command COMMAND phase initiator → target Bus phasea Header 4.4.7.2 Window date DATA OUT phase initiator → targeta TRANSFER LENGTH Bytes 6 to b Window descriptor block d Auto Byte e X, Y resolution XR, YR Bytes 2 to 3 and 4 toc Window identifier Byte f Upper left X,YULX, ULY Bytes 6 to 9, A to DRemarks Values under 0 in are omittedh Brightness Byte p Bit ordering Bytes 1E to 1F I Bit per pixel Byte 1An RIF reverse image format Byte 1D, bit m Halftone pattern Bytes lB to 1C lB reservedq Compression type, argument Bytes 20 to 4.4.7.3 Update of ScanPartner 600C OEM manual4.4.7.4 B&W Scanning Vender unique parameters Table 4-18 Vender unique parameters byte 28 and later4.4.7.4.2 Paper size byte 4.4.7.4.1 Vendor unique identification code ByteStatus B00001 CHECK CONDITION Sense Key X05 ILLEGAL REQUEST Specified a Paper Size. Set paper size used only in ADF modea ADF Byte 2A, Bit 4.4.7.5 Color Scanning Vender unique parametersTable 4-19 Vendor unique parameters byte 28 and later b Source Byte 2A, Bitf Line width Byte 2D to 2E d Highlight value Byte 2Be Shadow value Byte 2C Specifies line width in bytes for the current scan page4.4.8 OBJECT POSITION command POSITION TYPE 4.4.8.1 OBJECT POSITION command COMMAND phase initator → targeta Position type Byte Position typec Load object 4.4.8.2 Acknowledgmentb Unload object d Count Bytes 2 to4.4.8.3 ADF sequence 4.4.9 READ commandBus phase Stepb Data type qualifier Bytes 4 to 4.4.9.1 READ command COMMAND phase initiator → targeta Data type code Byte c Transfer length TL Bytes 6 tob For binary data 4.4.9.2 DATA IN phase target → initiatora Image data DATA TYPE CODE = C Pixel size data DATA TYPE CODE =Bus phase 4.4.10 Scan command4.4.10.1 SCAN Command phase initiator → target StepStatus of unit 4.5 Status STATUS phase target initiatorCode Phase 4.6 Messages4.6.1 ATN detection Status of unit4.6.2 Message types 4.6.2.1 COMMAND COMPLETE X00 MESSAGE IN phase target → initiatorATN detection phase 4.6.2.3 ABORT X06 MESSAGE OUT phase initiator → target4.6.2.4 MESSAGE REJECT X07 MESSAGE IN/OUT phase initiator → target Action4.6.2.7 BUS DEVICE RESET X0C MESSAGE OUT phase initiator → target 4.6.2.5 NO OPERATION X08 MESSAGE OUT phase initiator → target4.6.2.6 MESSAGE PARITY ERROR X09 MESSAGE OUT phase initiator → target Phase when ATN is detected4.6.2.8 IDENDIFY X80 TO XFF MESSAGE OUT phase initiator → target 4.7 Command Sequence 4.7.1 Initial sequence4.7.2.1 Read sequence for B&W mode 4.7.3 READ command sequence4.7.2 Read sequence 4.7.3.1 Single READ4.7.3.2 Multiple READ 4.8 Status Transition of Logical Unit HARD 4.9 Error TableERROR ILLEGALcomposition 4.10 Items for Specifying WindowImage BinaryPage 5.1 Online Diagnostics 5.2 Offline Diagnostics 5. Diagnostics5.1 Online diagnostics 5.3 Diagnostic FlowchartsTable 5-2 Offline diagnostics results 5.2 Offline diagnosticsError indication Ready LED5.3.2 Group 2 error flowchart Flatbed/ADF motor 5.3 Diagnostic flowcharts5.3.1 Group 1 error flowchart Lamp assembly 5.3.3 Group 3 error flowchart paper in ADF paper tray 5.3.4 Group 3 error flowchart no paper in ADF paper tray ADF paper-out