Manuals / Fujitsu / Computer Equipment / Scanner

Fujitsu 600C SCSI Bus, System configuration, Addresses of SCSI devices, Peripheral equipment

Models: 600C

1 95

Download 95 pages 10.46 Kb

Page 34

4.2 SCSI Bus

4.2.1System configuration

4.2.1.1System configuration

The SCSI bus connects up to eight SCSI units, each linked with a daisy chain. Both ends of the daisy chain require a terminator.

Each SCSI unit operates as an initiator or a target, so that a series of operations are performed between an initiator and target pair.

The system may be configured with any combination of initiators and targets as long as the number of the initiators and targets combined does not exceed eight.

4.2.1.2Addresses of SCSI devices

Every SCSI device on the bus is assigned a unique address (SCSI ID) that corresponds to the data bus bit number; ID#7 through ID#10 correspond to DB7 through DB0. The SCSI ID provides identification for specifying particular SCSI device when an initiator selects a target or when a target reconnects an initiator.

SCSI ID also represents the priority for using the bus in the arbitration phase. (A description regarding the bus phase is given later;) Priorities are given in the descending order of data bus bit numbers (DBn), with the highest priority placed on ID#7(DB7) and the lowest priority on ED#0(DB0).

4.2.1.3Peripheral equipment

With the basic specification, an initiator can designate up to eight peripheral devices (logical units) belonging tt a single target, where the peripheral devices are used as the I/O units of the initiator; Logical units are identified and selected by specifying their LUNs (logical unit numbers) in the IDENTIFY message or command (CDB: command descriptor block).

This scanner is equipped with a target and a logical unit, and its LUN is 000.

4-6

Image 34

Fujitsu 600C manual SCSI Bus, System configuration, Addresses of SCSI devices, Peripheral equipment

Contents

Fujitsu Inc Fujitsu ScanPartner 600C OEM ManualVersion Page 1. GENERAL Table of Contents2. SPECIFICATIONS 3. OPERATION5. DIAGNOSTICS 5.3.4 Group 3 error flowchart no paper in ADF paper tray Page 1. General 1.1 GeneralFigure 1-1 System Block Diagram 1.2.1 Outer View 1.2 Device ConfigurationFigure 1-2 ScanPartner 600C Outer View 1.2.2 Components 2.1 Functional Specifications 2.2 Environmental Specifications 2. Specifications2.1 Functional Specifications Table 2-1 Functional SpecificationsSpecifications Environmental SpecificationsTable 2-2 Environmental Specifications Remarks3. OPERATION 3.1 Removing the Shipping Bracket1. Remove the shipping retainer 2. Fasten the shipping retainer Figure 3-1 Power Switch 3.2 Power On/Off3.3 Indication Panel Figure 3-2 Indication PanelFigure 3-3 Signal cable connection 3.4 Setting the SCSI ID and Connecting the Interface CableTable 3-1 Names and functions of the indicators Content3.4.1 SCSI Cable Connection Host PC 3.5.2 Paper conditions 3.5 Paper Specifications3.5.1 Paper Size Figure 3-4 Paper size specifications3.5.2.2 FIatbed 3.5.2.3 Items to avoid3.5.3 Readable area Figure 3-5 ADF readable area3.6.1.1 When the document size is of letter/A4 size or smaller 3.6 Document Setting Method3.6.1 Flatbed Figure 3-6 Flatbed reading3.6.2.1 Setting the ADF paper chute 3.6.2 ADF3.6.1.2 When the document is a thick book Figure 3-7 Setting the ADF paper chute3.6.2.2 Placing the documents on the ADF paper chute Figure 3-8 Placing the document on the ADF paper chutea Angling the document sheets b Separating the sheets for easy feeding3.7 Cleaning 3.7.1 Cleaning the document cover and the document glass3.7.2 Cleaning inside the ADF Page 4.5 Status STATUS phase target initiator 4.6 Messages 4. INTERFACE4.1 Physical Specifications 4.2 SCSI Bus 4.3 Bus Phases 4.4 Commands 4.7 Command Sequence 4.8 Status Transition of Logical Unit3. Commands The following commands are supported by this scanner 4.1 Physical Specifications 4.1.1 ConnectionSpecifications 4.1.2 Physical Specification4.1.3 Termination Table 4-1 SCSI physical specificationsSignal Name 4.1.4 Pin assignmentsSignal Name Pin Number4.2.1.1 System configuration 4.2.1 System configuration4.2 SCSI Bus 4.2.1.2 Addresses of SCSI devices4.2.2 Bus signals Table 4-2 Bus signals4.2.3 Bus signal drive conditions Table 4-3 Bus phases vs. signal drive sources 1/2Table 4-4 Method of driving the interface signal 4.3 Bus PhasesFigure 4-2 Phase sequence Definition Table 4-5 Signal delay times definitionTime AssertionTime 4.3.1 BUS FREE phaseTable 4.5 Signal delay times definition definitionothers 4.3.2 ARBITRATION phase4-12 Page 4.3.3 SELECTION phase Phase 4.3.4 INFORMATION TRANSFER phasesTable 4-6 INFORMATION TRANSFER phase type DB7 to 9,P4.3.4.1 Asynchronous information transfer a Asynchronous transfer from target to initiatorb Asynchronous transler from initiator to target 4.4 Commands b Relative addressing is not supportedCommand 4.4.1 RESERVE UNIT commandTable 4-7 Commands d A bit and field described as Reserved area TP third party Byte 4.4.1.1 RESERVE UNIT command COMMAND phase initiator Õ targetb TPID third party device ID Byte 4.4.2 RELEASE UNIT command 4.4.2.1 RELEASE UNIT command COMMAND phase initiator → targetTable 4-10 INQUIRY command 4.4.3 INQUIRY command4.4.3.1 INQUIRY command COMMAND phase initiator → target Bus phaseCAllocation length Byte a EVPD enable vital product data Byteb Page code Byte EVPD4.4.3.2 Inquiry data DATA IN phase target → initiator f Asynchronous event notification capability AENC Byte l sftRst Soft Reset Bytee ISO version, ECMA version, ANSI approved version Byte g Response data format ByteTable 4-11 REQUEST SENSE command 4.4.4 REQUEST SENSE command4.4.4.1 REQUEST SENSE command COMMAND phase initiator → target Bus phasea Allocation length Byte 4.4.4.2 Sense data DATA EN phase target → initiatorb Error code Byte a Valid Bytee EOM end of medium Byte f ILI incorrect length indicator Byted FM file mark Byte g Sense key ByteTable 4-14 SEND DIAGNOSTIC command 4.4.5 SEND DIAGNOSTIC commandj Command-specific information bytes Bytes 8 to B Bus phaseBus phase 4.4.5.1 SEND DIAGNOSTIC command COMMAND phase initiator → targetTable 4.14 SEND DIAGNOSTIC command StepBus phase 4.4.6 TEST UNIT READY command4.4.5.2 Contents of self-test 4.4.5.3 Results of self-testByte 4.4.6.1 TEST UNIT READY command COMMAND phase initiator → target4.4.6.2 Acknowledgment Operation codeTable 4-16 SET WINDOW command 4.4.7 SET WINDOW command4.4.7.1 SET WINDOW command COMMAND phase initiator → target Bus phasea TRANSFER LENGTH Bytes 6 to 4.4.7.2 Window date DATA OUT phase initiator → targeta Header b Window descriptor block d Auto Byte e X, Y resolution XR, YR Bytes 2 to 3 and 4 toc Window identifier Byte f Upper left X,YULX, ULY Bytes 6 to 9, A to Dh Brightness Byte Values under 0 in are omittedRemarks p Bit ordering Bytes 1E to 1F I Bit per pixel Byte 1An RIF reverse image format Byte 1D, bit m Halftone pattern Bytes lB to 1C lB reservedq Compression type, argument Bytes 20 to 4.4.7.3 Update of ScanPartner 600C OEM manual4.4.7.4 B&W Scanning Vender unique parameters Table 4-18 Vender unique parameters byte 28 and later4.4.7.4.2 Paper size byte 4.4.7.4.1 Vendor unique identification code ByteStatus B00001 CHECK CONDITION Sense Key X05 ILLEGAL REQUEST Specified a Paper Size. Set paper size used only in ADF modea ADF Byte 2A, Bit 4.4.7.5 Color Scanning Vender unique parametersTable 4-19 Vendor unique parameters byte 28 and later b Source Byte 2A, Bitf Line width Byte 2D to 2E d Highlight value Byte 2Be Shadow value Byte 2C Specifies line width in bytes for the current scan page4.4.8 OBJECT POSITION command POSITION TYPE 4.4.8.1 OBJECT POSITION command COMMAND phase initator → targeta Position type Byte Position typec Load object 4.4.8.2 Acknowledgmentb Unload object d Count Bytes 2 to4.4.8.3 ADF sequence 4.4.9 READ commandBus phase Stepb Data type qualifier Bytes 4 to 4.4.9.1 READ command COMMAND phase initiator → targeta Data type code Byte c Transfer length TL Bytes 6 tob For binary data 4.4.9.2 DATA IN phase target → initiatora Image data DATA TYPE CODE = C Pixel size data DATA TYPE CODE =Bus phase 4.4.10 Scan command4.4.10.1 SCAN Command phase initiator → target StepCode 4.5 Status STATUS phase target initiatorStatus of unit Phase 4.6 Messages4.6.1 ATN detection Status of unit4.6.2 Message types 4.6.2.1 COMMAND COMPLETE X00 MESSAGE IN phase target → initiatorATN detection phase 4.6.2.3 ABORT X06 MESSAGE OUT phase initiator → target4.6.2.4 MESSAGE REJECT X07 MESSAGE IN/OUT phase initiator → target Action4.6.2.7 BUS DEVICE RESET X0C MESSAGE OUT phase initiator → target 4.6.2.5 NO OPERATION X08 MESSAGE OUT phase initiator → target4.6.2.6 MESSAGE PARITY ERROR X09 MESSAGE OUT phase initiator → target Phase when ATN is detected4.6.2.8 IDENDIFY X80 TO XFF MESSAGE OUT phase initiator → target 4.7 Command Sequence 4.7.1 Initial sequence4.7.2.1 Read sequence for B&W mode 4.7.3 READ command sequence4.7.2 Read sequence 4.7.3.1 Single READ4.7.3.2 Multiple READ 4.8 Status Transition of Logical Unit HARD 4.9 Error TableERROR ILLEGALcomposition 4.10 Items for Specifying WindowImage BinaryPage 5.1 Online Diagnostics 5.2 Offline Diagnostics 5. Diagnostics5.1 Online diagnostics 5.3 Diagnostic FlowchartsTable 5-2 Offline diagnostics results 5.2 Offline diagnosticsError indication Ready LED5.3.1 Group 1 error flowchart Lamp assembly 5.3 Diagnostic flowcharts5.3.2 Group 2 error flowchart Flatbed/ADF motor 5.3.3 Group 3 error flowchart paper in ADF paper tray 5.3.4 Group 3 error flowchart no paper in ADF paper tray ADF paper-out