How to fix signal cable in cable gland | Furuno 1833C-BB, 1953C-BB

Tubing

Shield

Vinyl sheath	Bolt
within 4 cm

Plate

Gasket

Flat

washer

CABLE GLAND

How to fix signal cable in cable gland

6. Unfasten four screws shown in the figure below.

Four screws

Antenna unit chassis, cover opened

7. Pass the signal cable through the cable protector.

Cable protector

Antenna unit chassis, cover opened

1-25

Image 35

Furuno 1833C-BB, GD-1900C-BB, 1953C-BB, 1943C-BB, 1933C-BB, 1823C-BB manual How to fix signal cable in cable gland

Contents

Back 00014791603 Safety Instructions Table of Contents Equipment Lists Optional supply System Configurations Single-unit NavNet system GD-1900C-BB Single-unit NavNet system GD-1900C-BB Three-or-more-unit NavNet system Three-or-more-unit NavNet system Two-unit NavNet system Two-unit NavNet system Mounting Flush mounting of display unit Flush mounting Desktop mounting of display unit Desktop mounting Mounting the Processor Unit Processor unit, mounting dimensions Mounting the Antenna Unit of MODEL1823C-BB Typical antenna unit placement on sailboat and powerboat Antenna unit, showing location of mounting hardware How to fasten the mounting base to platform Antenna unit, inside view Snap holder Remove and discard the packing material GND Location of EMI core Sectional view EMI core, putting into core case How to pass the rotation detector cable Antenna unit, clamping the rotation detector cable Mounting the optional mounting bracket How to assemble and mount the optional mounting bracket Antenna unit Mounting the Antenna Unit of MODEL1833C-BB Antenna unit, inside view How to fasten the radome base to the mounting platformWiring and final preparation Antenna unit, cover removed RF unit Signal cable, antenna unit side How to position the radome cover How to attach EMI core Mounting bracket contents Mounting the Antenna Unit of MODEL1933C-BB/1943C-BB/1953C-BB Fastening the radiator bracket to the antenna unit chassis Fastening the radiator to the radiator bracketCoating the antenna with silicone sealant Antenna unit Location of rubber mat Fixing the antenna unit chassis How to fasten antenna unit to mounting platform Ground Antenna unit chassis, upper chassis separated Using inside fixing holes of the antenna housing Antenna unit chassis, cover opened Passing the signal cable through the cable gland assembly How to fix signal cable in cable gland Torque 9.8 ±0.1 N .m Power supply unit Mounting the Power Supply Unit of MODEL1953C-BB Desktop mount Mounting the Memory Card Interface Unit Standard Wiring Wiring DJ-1 Waterproofing cap and connector nut, sectional view Connecting GP-310B/320B to Data 2 port Connecting GP-310B/320B to Data 2 port Power supply unit, cover removed Wiring of Power Supply Unit MODEL1953C-BB only Replacement of the fuse HUB Connection of CU-200 Installation setup menu How to Access the Installation MenuHow to access the Installation menu Host name window Network Setup MenuNetwork setup menu NavNet equipment default settings Contents of Network setup menu Radar setup menu Radar Setup Menu Antenna Type Power supply unit, cover removed Examples of improper and correct sweep timing Tuning setup menu Video adjustment setting window Timing adjust setting menuTiming adjustment setting display Heading adjustment setting display Heading Adjustment Radar antenna height setting window Main bung suppression setting window Heading data setting window STC curve setting window Navigation Data Source Nav setup menuChecking Magnetron Heater Voltage Position Source Furuno BB GPS ALL Antenna height window GPS setup menu On next Contents of GPS sensor settings menu Contents of GPS sensor settings menu con’t Nmea data sentences Setting up Data PortsDATA1, DATA2 Port menus Contents of Data 1 and DATA2 Port menus Remote System Setting Processor unit cover removed External Buzzer ConnectionExternal buzzer Name Type Code No Qty ARP-11 contentsARP Kit ARP-11 Necessary parts 19P1001 board J112 This page is intentionally left blank Model 1823C-BB Model 1833C-BB Page Page M1933C-BB/1943C-BB Page Page ＰａｃｋｉｎｇＬｉｓｔ付属品表 PSU-005 CU-200-NAVBB 工事材料表 CU-200 Desktop mount kit Page Hatai Page Page Page Page Page Hatai Page Page 船舶用レーダー Interconnection Diagram Hatai Marine Radar