Drive Wheel Parts | Grizzly G0504 specs

Drive Wheel Parts

��

��

��

��

��

��

��

��

��

��		��	��
		��
	��
��	��
	��		��	��
			��	��
			��	��
			��	��
				��
	��
	��
��				��
��
				��
			��	��
			��	��
			��	��
			��
			��
		��
	��

REF	PART #	DESCRIPTION

1601	P0504428A	LOCK NUT AN11
1602	PTLW08M	EXT TOOTH WASHER 10MM
1603	P0504429A	LOCK RING
1604	PSB73M	CAP SCREW M12-1.75 X 50
1605	PLW05M	LOCK WASHER 12MM
1606	P0504403	RIGHT BLADE WHEEL
1607	P0504455	INT RETAINING RING 90MM
1608	P0504456	OIL SEAL TC-70 X 90 X 8
1609	P32011	BEARING 32011
1610	P05041610	BEARING SEAT-LEFT

REF	PART #	DESCRIPTION

1611	P05041611	BELT 5V X 740
1612	P32012	TAPER ROLLER BEARING 32012
1613	P05041613	OIL SEAL TC-75 X 95 X 10
1614	P05041614	INT RETAINING RING 95MM
1615	PZERK2	GREASE FITTING PT 1/8
1616	P05041616	RIGHT WHEEL SHAFT
1617	PB25M	HEX BOLT M12-1.75 X 25
1618	PN09M	HEX NUT M12-1.75
1619	P05041619	WHEEL ADJUSTMENT PLATE

-56-	G0504 16" Horizontal Resaw Bandsaw

Image 58

Grizzly G0504 owner manual Drive Wheel Parts

Contents

Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Service Adjustments Parts General Information Commentary Machine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Phase Power Circuit Requirements Grounding Converting to Inside of electrical box Main motor 440V wiring Machine Features Main FeaturesPage Memory Preset Keys A, B, C, D-Allows Control Panel Piece Inventory SET UPAbout this Section Unpacking Hardware Recognition Chart Clean Up Site Considerations Removing Resaw from Crate Pallet Mounting Resaw to the Floor Installing Tensioning Blade To install and tension the blade Adjusting Blade Guides Always de-tension blade after use To adjust the upper guide block Support Bearing To adjust the support bearings Power Source Connecting to DustTo connect the resaw to a dust collector Power on switch Test Run Operations Operation Safety Conveyor ControlsTo operate the infeed conveyor To set the blade height with the keypad Setting Blade HeightCalibrating Digital Display To calibrate the digital display To use the stored memory preset in the a key Setting Memory Using Memory ButtonTo store a height in the a memory preset key To set the memory function Resawing To perform a resawing operation Blade Information H0580-Pneumatic Grease Gun AccessoriesH4959-Coolant Dispenser H1300 H1298 G7984 H2347 H0736 Miscellaneous MaintenanceCleaning Belts Grease Fittings Hydraulic System Minor Service Check the hydraulic fluid level daily Hydraulic System Major Service To inspect the hydraulic fluid To clean the bottom of the tank To clean the tank screenTo fill the tank with new fluid About Service Service AdjustmentsAdjusting Lower Blade Guides Adjusting V-Belt Tension To adjust the tension for the hydraulic pump V-belt Replacing V-Belts Adjusting Main Conveyor TableTo check the main conveyor table alignment Tracking Conveyors To set the conveyor tracking Replacing Conveyors To replace the conveyor belts Disconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Troubleshooting Underpowered Symptom Possible Cause Possible Solution Housing Parts Parts Housing Parts List Description Frame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Hydraulic System Parts List Connector 3/8H X 3/8H Electrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page