Manuals / Grizzly / Power Tools / Saw

Grizzly G0504 owner manual Installing Tensioning Blade, To install and tension the blade

Models: G0504

1 76

Download 76 pages 31.87 Kb

Page 21

Installing &

Tensioning Blade

These instructions are hazardous if done while the machine is connect- ed to power. Disconnect power during this entire procedure!

Blade installation can be done by one person but is easiest if done with two people.

To install and tension the blade:

1.Put on safety glasses and heavy leather gloves.

2.Open the wheel cover to gain access to the wheels.

3.Hold the blade from each side, and position it in front of the wheels so the blade teeth are facing the front of the machine.

4.Carefully fit the blade over each wheel, and position it between the blade guides as shown in Figure 13. Make sure the teeth point toward the right-hand side of the machine, as you are facing the front.

Figure 13. Blade positioned between

blade guides.

G0504 16" Horizontal Resaw Bandsaw

5.Position the blade on the wheels so that the tooth gullet is approximately 1⁄16" over the edge of the wheel, as shown in Figure 14. Also, see the blade illustration in Figure 15 for more details.

Figure 14. Blade positioned on wheel.

Figure 15. Illustration of proper blade position.

-19-

Image 21

Grizzly G0504 owner manual Installing Tensioning Blade, To install and tension the blade

Contents

Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Parts Service AdjustmentsCommentary General InformationMachine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Circuit Requirements Phase PowerInside of electrical box Grounding Converting toMain motor 440V wiring Main Features Machine FeaturesPage Control Panel Memory Preset Keys A, B, C, D-AllowsAbout this Section SET UPPiece Inventory UnpackingHardware Recognition Chart Clean Up Site Considerations Mounting Resaw to the Floor Removing Resaw from Crate PalletTo install and tension the blade Installing Tensioning BladeAlways de-tension blade after use Adjusting Blade GuidesTo adjust the support bearings To adjust the upper guide block Support BearingConnecting to Dust Power SourceTo connect the resaw to a dust collector Test Run Power on switchOperation Safety Conveyor Controls OperationsTo operate the infeed conveyor Calibrating Digital Display Setting Blade HeightTo set the blade height with the keypad To calibrate the digital displayTo store a height in the a memory preset key Setting Memory Using Memory ButtonTo use the stored memory preset in the a key To set the memory functionTo perform a resawing operation ResawingBlade Information H4959-Coolant Dispenser AccessoriesH0580-Pneumatic Grease Gun H1300 H1298 G7984 H2347 H0736Cleaning MaintenanceMiscellaneous BeltsGrease Fittings Check the hydraulic fluid level daily Hydraulic System Minor ServiceTo inspect the hydraulic fluid Hydraulic System Major ServiceTo clean the tank screen To clean the bottom of the tankTo fill the tank with new fluid Service Adjustments About ServiceAdjusting Lower Blade Guides To adjust the tension for the hydraulic pump V-belt Adjusting V-Belt TensionAdjusting Main Conveyor Table Replacing V-BeltsTo check the main conveyor table alignment To set the conveyor tracking Tracking ConveyorsTo replace the conveyor belts Replacing ConveyorsDisconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Underpowered TroubleshootingSymptom Possible Cause Possible Solution Parts Housing PartsDescription Housing Parts ListFrame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Connector 3/8H X 3/8H Hydraulic System Parts ListElectrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page