Machine Data Sheet | Grizzly G0504 instruction

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901

MODEL G0504 16" HORIZONTAL RESAW BANDSAW

Overall Dimensions:
Conveyor Table		16" W x 102" D
Height From Floor To Table		40"
Height From Floor To Return Table		30"
Overall Height (With Door Open)		831⁄2"
Overall Width		85"
Overall Depth		108"
Shipping Weight		4080 lbs.
Net Machine Weight		3300 lbs.
Crate Size		73" x 48" x 61"
Footprint		321⁄4" W x 451⁄4" L
Capacities:
Maximum Workpiece Width and Height		16" W x 10" H
Minimum Workpiece Length		16" L
Distance From Blade to Conveyor Table		1⁄4"-10"
Saw Wheel Diameter		Ø28" x 15⁄16"W
Saw Blade Size		180" L x 1" W x .035" T (.063 kerf)
Saw Blade Speed		7300 FPM
Feed Conveyor Belt Size		151⁄4" x 2153⁄4" x 1pc
Return Conveyor Belt Size		71⁄4" x 2153⁄4" x 1pc
Feed Speed		0-61 FPM
Construction:
Frame		Steel
Conveyor Table		Steel
Conveyor Belt		Rubber
Wheels		Steel
Wheel Cover		Pre-Formed Steel
Blade Guides		Ceramic
Pressure Roller		4" Cast Iron w/Polyurethane Tire
Main Motor:
Type		TEFC Induction
Horsepower		25 HP
Phase / Voltage		3-Phase / 220V/440V
Amps		60/30A
Cycle / RPM		60 Hertz / 1725 RPM
Switch	220V Magnetic w/Thermal Overload Protector
Bearings		Shielded & Lubricated Ball Bearings
Hydraulic Pressure		775 PSI (55KG/CM2)
Elevation Motor:
Type		TEFC Induction
Horsepower		1⁄2 HP
Phase ⁄ Voltage		3-Phase / 220V/440V
Amps		2.2/1.1A
Cycle ⁄ RPM		60 Hertz / 1725 RPM

Features:

.............................................................................................................4" Dust Port x 2

...........................................................................................................Return Conveyor

................................................................Hydraulic Blade Tension Control & Indicator

.....................................................................................Powered Saw Wheel Elevation

...................................Digital Position Controller for Accurate Saw Wheel Positioning

Specifications, while deemed accurate, are not guaranteed.

-4-	G0504 16" Horizontal Resaw Bandsaw

Image 6

Grizzly G0504 owner manual Machine Data Sheet

Contents

Model G0504 Horizontal Resaw Bandsaw Page Table of Contents Service Adjustments Parts General Information Commentary Machine Data Sheet G0504 16 Horizontal Resaw Bandsaw G0504 16 Horizontal Resaw Bandsaw Additional Safety Instructions for Bandsaws Additional Safety Instructions for Hydraulics Phase Power Circuit Requirements Grounding Converting to Inside of electrical box Main motor 440V wiring Machine Features Main FeaturesPage Memory Preset Keys A, B, C, D-Allows Control Panel Piece Inventory SET UPAbout this Section Unpacking Hardware Recognition Chart Clean Up Site Considerations Removing Resaw from Crate Pallet Mounting Resaw to the Floor Installing Tensioning Blade To install and tension the blade Adjusting Blade Guides Always de-tension blade after use To adjust the upper guide block Support Bearing To adjust the support bearings Connecting to Dust Power SourceTo connect the resaw to a dust collector Power on switch Test Run Operation Safety Conveyor Controls OperationsTo operate the infeed conveyor To set the blade height with the keypad Setting Blade HeightCalibrating Digital Display To calibrate the digital display To use the stored memory preset in the a key Setting Memory Using Memory ButtonTo store a height in the a memory preset key To set the memory function Resawing To perform a resawing operation Blade Information H0580-Pneumatic Grease Gun AccessoriesH4959-Coolant Dispenser H1300 H1298 G7984 H2347 H0736 Miscellaneous MaintenanceCleaning Belts Grease Fittings Hydraulic System Minor Service Check the hydraulic fluid level daily Hydraulic System Major Service To inspect the hydraulic fluid To clean the tank screen To clean the bottom of the tankTo fill the tank with new fluid Service Adjustments About ServiceAdjusting Lower Blade Guides Adjusting V-Belt Tension To adjust the tension for the hydraulic pump V-belt Adjusting Main Conveyor Table Replacing V-BeltsTo check the main conveyor table alignment Tracking Conveyors To set the conveyor tracking Replacing Conveyors To replace the conveyor belts Disconnect the resaw from the power source Blade Tracking Wheel Alignment Screws Page Troubleshooting Underpowered Symptom Possible Cause Possible Solution Housing Parts Parts Housing Parts List Description Frame Parts Frame Parts List Elevation Parts Elevation Parts List Blade Guide Parts Adjustment ROD Bracket Tensioning Wheel Parts Tensioning Wheel Parts List Drive Wheel Parts Hydraulic Pump Parts Main Conveyor Table Parts Main Conveyor Table Parts List Return Conveyor Table Parts Rear Hold Down Parts Front Hold Down Parts Front Hold Down Parts List Hydraulic System Parts Hydraulic System Parts List Connector 3/8H X 3/8H Electrical System Parts Electrical System Parts Electrical System Parts List Warranty and Returns Page Page Page