Cleanup, Site Considerations, Wheel Assembly | Grizzly G0604

Cleanup

The unpainted cast iron surfaces are coated with a waxy oil to protect them from corrosion during shipment. Remove this protective coating with a solvent cleaner or citrus-based degreaser such as Grizzly’s G7895 Degreaser. To clean thor- oughly, some parts may need to be removed. For optimum performance from your machine, make sure you clean all moving parts or slid- ing contact surfaces that are coated. Avoid chlorine-based solvents, such as acetone or brake parts cleaner, as they may damage painted surfaces should they come in contact.

Site Considerations

Machine Placement

Consider the jointer dimensions and size of mate- rial to be processed through each machine, and space for auxiliary stands, work tables or other machinery when establishing a location for your jointer. See Figure 4 for the Model G0604 over- head view dimensions.

551⁄2"

25"

Wheel Assembly

Components and Hardware Needed:	Qty
Wheel Assembly	1
Stand Assembly w/Motor	1
Hex Bolt M8-1.25 x 50	1
Flat Washer 8mm	1
Hex Bolts M10-1.5 x 55	2
Flat Washers 10mm	2
Hex Nuts M10-1.5	2
To attach the wheel:

1.Carefully lay the stand on its side so you can access the underside.

2.Bolt the wheel assembly to the stand with the provided hardware as shown in Figure 5.

Figure 4. Model G0604 overhead view	Figure 5. Bolting the wheel assembly to the
dimensions.	stand.
3.	Turn the stand rightside up.

G0604 6" X 56" Jointer

-13-

Image 15

Grizzly G0604 Cleanup, Site Considerations, Wheel Assembly, Components and Hardware Needed Qty, To attach the wheel

Contents

Model G0604 Page Table of Contents Warranty and Returns Introduction ForewordContact Info Machine Data Sheet Identification Safety Instructions for Machinery Safety Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Jointers 110V Operation Circuit Requirements Unpacking SetupSetup Safety Items Needed for Setup Jointer Box Figure Qty Stand Assembly w/MotorAssembly Fasteners Qty Inventory Hardware Recognition Chart Components and Hardware Needed Qty CleanupWheel Assembly Site Considerations To install the V-belt JointerV-BeltTo mount the jointer to the stand To check the outfeed table height Checking Outfeed Table Height To install the extension table Setting Outfeed Table Height onExtension Table Fence To install the fence Cutterhead Guard Pedestal SwitchTo install the cutterhead guard To install the pedestal switch Dust Port Knife Setting Jig Test Run Recommended Factory adjustments that should be verified Operation Safety Basic Controls OperationsStart & Stop Buttons Figure Tilt lock and plunger locations Stock Inspection and Requirements Squaring Stock Minimum dimensions for edge Jointing To surface plane on the jointer Surface Planing To edge joint on the jointer Edge Jointing To bevel cut on the jointer Bevel Cutting Accessories H9218-6 Byrd Shelix CutterheadG3631-Jointer/Planer Knife Hone Dispoz-A-BladeHolder and Knife H1300 H1298 G7984 H2347 H0736 Our most popular safety glasses Lubrication MaintenanceBelt Cleaning Schedule Troubleshooting Guide Service Cutting Adjusting/Replacing Knives Inspecting KnivesTo inspect the knives Tools Needed Qty To adjust/replace the knivesPage To check the outfeed table parallelism Checking/Adjusting Table Parallelism To check the infeed table parallelism To adjust the table parallelism To set the outfeed table height Setting Outfeed Table Height Positive stop bolts for infeed table Setting Infeed Table To calibrate the depth scale Setting Fence StopsCalibrating Depth Scale To set the 45 outward fence stop To set the 90˚ fence stop Wiring Diagram Electrical Components Jointer Parts Breakdown Description Jointer Parts List Bumper Stand/Motor Parts Breakdown Stand/Motor Parts List PLABEL-29 Cutterhead Guard Label Warranty and Returns G0604 6 X 56 Jointer Comments Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog