Identification, G0606X identification | Grizzly G0605X/G0606X

Identification

A	B	C	D	E	F	G
					F

			H
Q
			I
P
O	M	L	K
		L
			J


	N

		Figure 1. G0606X identification.
A.	Front Rail	J.	Tool Chest (Optional)
B.	Outfeed Table	K.	Blade Tilt Handwheel & Lock
C.	Blade Guard and Splitter	L.	Blade Angle Digital Readout
D.	Miter Gauge	M.	Blade Tilt Scale
E.	Fence	N.	Blade Height Handwheel
F.	Fence Scale Indicator	O.	Dust Port
G.	Front (Main) Extension Table	P.	ON/OFF Switch w/Emergency STOP
H.	Fence Lock Handle		Paddle
I.	Support Leg	Q.	Motor Cover

-6-	G0605X/G0606X Extreme Series 12" Table Saw

Image 8

Grizzly G0605X/G0606X owner manual Identification, G0606X identification

Contents

Extreme Series Table SAW Page Table of Contents Accessories Maintenance Contact Info IntroductionForeword Machine Data Sheet Model G0606X 12 Extreme Series Table SAW Identification G0606X identification Safety Safety Instructions for Machinery Always Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Table Saws Below are tips to avoid the most common causes of kickback Preventing KickbackProtecting Yourself From Kickback Glossary of Terms Power Connection Device Circuit RequirementsOperation Full Load Amperage Draw Draw Extension Cords 220V Only Phase Converter Precaution440V Conversion SET UP Set Up SafetyItems Needed for Set Up Unpacking Fence Rail Inventory Machine InventoryFence Inventory Extension Table Inventory Outfeed Table Inventory Hardware Recognition Chart Clean Up Placement LocationSite Considerations Floor Load Components and Hardware Needed Qty To install the front and rear railsExtension Table Foot installed on support leg To install the outfeed table Outfeed Table To install the blade Saw Blade To change the arbor To install and adjust the table insertArbor Table Insert To install the blade guard Blade Guard Splitter Miter Gauge On/Off SwitchRiving Knife To connect a dust collection hose Fence ComponentsDust Collection Recommended Adjustments Recommended adjustment checklistTest Run To test run the machine Example of switching incoming power Basic Controls Operation SafetyOperations Disabling On/Off Switch Ripping blade featuresCrosscut blade features Combination blade features Laminate blade features Dado Blades Workpiece Inspection Non-Through Through CutsNon-Through Cuts Through Cuts Ripping Typical ripping operation To perform a miter cut To make a crosscut using the miter gaugeCrosscutting Miter Cuts Dado Cutting To use a standard saw blade to cut dadoes Rabbet Cutting To cut rabbets with the dado blade To cut rabbets with the standard blade Resawing Resaw Barrier Auxiliary Fence Resawing Operations Components Needed for ResawingPage Accessories G7895-Citrus DegreaserH1234-Table Saw Bench Guide H7583-Grizzly Tenoning Jig G7581-Superbar G7582-Master Plate G2370-SHOP FOX Board Buddies Maintenance CleaningSchedule Lubrication Motor & Electrical ServiceTroubleshooting Table Saw Operations To remove the flat belt Replacing Flat BeltTools Needed Qty To install the new belt To set the 45 stop bolt Blade Tilt StopsTo set the 90 stop bolt To set the digital readout To adjust the tilt indicator arrowDigital Readout To adjust the blade parallel to the miter slot Miter Slot to Blade Parallelism Shim procedure diagram a Adjusting Fence To adjust the blade by moving the tableBlade Alignment Square and Height Miter Gauge G0605X/G0606X Electrical Components G0605X motor junction box G0605X Wiring Diagram G0606X magnetic switch prewired to Phase G0606X Electrical Components G0606X Wiring Diagram G0606X Wiring Diagram Cabinet, Motor & Main Table Breakdown Cabinet, Motor & Main Table Parts List Description Description Blade Guard Assembly Breakdown Blade Guard Parts List Fence Assembly Breakdown Fence Parts List Miter Gauge Assembly Breakdown Miter Gauge Parts List Extension Table Assembly Outfeed Table Assembly Breakdown Outfeed Table Parts List Guard and ANTI-KICK Back Label Warranty and Returns Page Page