Decal DC-1227 | GSI Outdoors PNEG-951 specs

Decal: DC-1227

Decal DC-1227 is located on the fan/heater access door.

Decal: DC-1225

Decal DC-1225 is located on the fan/heater access door.

Decal: DC-1229

Decal DC-1229 is located on each of the meter roll access doors.

PNEG-951

13

Image 13

GSI Outdoors PNEG-951 manual Decal DC-1227

Contents

3 Module Network Portable Dryer Models Page Table of Contents Drying Charts Module Network Dryer Manual Introduction Section GSI GROUP, INC. Warranty Safety First Dryer Operation Decal DC-889 Decal DC-972 Decal DC-1227 Decal DC-973 USE Caution in the Operation of this Equipment PNEG-951 Control Panel Switch Panel Layout Drying Mode Switch Control Power SwitchLoad Auger Switch FAN Switch Outside Light Switch Moisture Control SwitchRUN Switch Stop Switch Setup Button Screens Button Delay ButtonOut of Grain Time Set Out of Grain Meter Roll SP Avg View Grain Temps User Hour Meter DRY Button Help ButtonCool Button Unload Button Stats Button PNEG-951 Dryer Pre Season Checks Inspect the Metering Rolls Electrical PowerRUN Button Fuel Check Unload ONE Speed Operation Load AugerUnload TWO Speed Operation Metering Roll Operation Burner Safety FAN SwitchesBurner Test Fire Meter Roll 2 Speed Display Emergency Dryer Shutdown Dryer Shutdown PNEG-951 Dryer Startup and Operation Timer and Delay Settings Initial Setup ParametersFan and Auger Delays Dryer Shutdown Load Delay OUT of Grain TMR position Unload Delay Drying mode switch is in the Continuous position Setting Up The Temperature Set Points Startup Startup Procedure Full Heat-Continuous Flow Operation Continuous Flow Drying Mode Dry and Cool-Continuous Flow Operation Continuous-Batch Operation Staged Batch Drying Mode PNEG-951 Dry Timer Main Display Screen Operating Display Screens PNEG-951 Safety Circuit Shutdown Messages Air Switch x Stuck FAN and Heater Generated ErrorsFan x Loss of Airflow Fan x No Airflow Grain Temp Short Housing x High LimitGrain x Overheat Ignition Failure Motor Overload Illegal FlamePlenum Temp Open Plenum Temp Short Vapor x High Limit INPUT/OUTPUT Generated ErrorsAir System Failure Aux Load Overload Load Motor Overload Grain Discharge WarningMeter Rolls Failed Out of Grain User Safety Master Display Generated ErrorsCont-Batch Mode Chng Unload Motor Overload Network Failed Mast Network Failed I/O Service and Maintanance Lubrication Procedure Seasonal Inspection and Service FAN Blade Removal and Installation FAN Removaland Installation FAN Motor Removal Heater Parts Removal and Installation Main Controls Meter Roll Servicing HOW to Clear a Jammed Metering Roll Trouble Analysis Procedure PNEG-951 PNEG-951 PNEG-951 PNEG-951 Special Setup Screens AIR Switch Testing Meter Roll DisableMeter Roll Reverse Select Unload Method Reverse time Attempt to Refill Select Dryer AddressModel Number FAN/HEATER Select Temperature Scale SET Time & Date Possible reasons for using On/Off burner Contrast Adjustment PNEG-951 Drying Charts Series Dryers Continuous Dry & Cool Staged Batch Continuous Full Heat Continuous Dry & Cool Staged Batch PNEG-951 Technical Reference Control Panel Jumper Wiring Control Panel Internal Wiring PNEG-951 PNEG-951 PNEG-951 PNEG-951 PNEG-951 PNEG-951 Lower Control BOX Back Panelwiring Network FAN/HEATER Interface FAN Computer Pinouts FAN Control BOX Upper Terminal Strip Upper Back Panel Control Wiring 100 PNEG-951 PNEG-951 101 GSI Group, Inc 1004 E. Illinois St Assumption, IL Phone Fax