Decal DC-889 | GSI Outdoors PNEG-951 instruction

The GSI Group,Inc.recommends contacting yourlocalpower company,andhaving arepresentative survey your installation so the wiring is compatible with their system, and adequate power is supplied to your unit. Safety decals should be read and understood by all people in the grain handling area.

If a decal is damaged or is missing contact: The GSI Group, Inc.

1004 E. Illinois St. Assumption, IL 62510 217-226-4421

A free replacement will be sent to you.

Decal: DC-1224

Decal DC-1224 is located in two places on the fan/ heater control box. One on the lid and one on the front of the fan heater control box. Another location for this decal is insidethe upper control boxfor the dryer.

Decal DC-889 has two locations. One inside the fan/heater control box and another on the dryer upper con- trol box door next to the main power disconnect.

Decal: DC-889

PNEG-951

11

Image 11

GSI Outdoors PNEG-951 manual Decal DC-889

Contents

3 Module Network Portable Dryer Models Page Table of Contents Drying Charts Module Network Dryer Manual Introduction Section GSI GROUP, INC. Warranty Safety First Dryer Operation Decal DC-889 Decal DC-972 Decal DC-1227 Decal DC-973 USE Caution in the Operation of this Equipment PNEG-951 Control Panel Switch Panel Layout FAN Switch Control Power SwitchDrying Mode Switch Load Auger Switch Stop Switch Moisture Control SwitchOutside Light Switch RUN Switch Setup Button Out of Grain Time Delay ButtonScreens Button Set Out of Grain Meter Roll SP Avg View Grain Temps User Hour Meter Unload Button Help ButtonDRY Button Cool Button Stats Button PNEG-951 Dryer Pre Season Checks Fuel Check Electrical PowerInspect the Metering Rolls RUN Button Metering Roll Operation Load AugerUnload ONE Speed Operation Unload TWO Speed Operation Meter Roll 2 Speed Display FAN SwitchesBurner Safety Burner Test Fire Emergency Dryer Shutdown Dryer Shutdown PNEG-951 Dryer Startup and Operation Dryer Shutdown Initial Setup ParametersTimer and Delay Settings Fan and Auger Delays Load Delay OUT of Grain TMR position Unload Delay Drying mode switch is in the Continuous position Setting Up The Temperature Set Points Startup Startup Procedure Full Heat-Continuous Flow Operation Continuous Flow Drying Mode Dry and Cool-Continuous Flow Operation Continuous-Batch Operation Staged Batch Drying Mode PNEG-951 Dry Timer Main Display Screen Operating Display Screens PNEG-951 Safety Circuit Shutdown Messages Fan x No Airflow FAN and Heater Generated ErrorsAir Switch x Stuck Fan x Loss of Airflow Ignition Failure Housing x High LimitGrain Temp Short Grain x Overheat Plenum Temp Short Illegal FlameMotor Overload Plenum Temp Open Aux Load Overload INPUT/OUTPUT Generated ErrorsVapor x High Limit Air System Failure Out of Grain Grain Discharge WarningLoad Motor Overload Meter Rolls Failed Unload Motor Overload Master Display Generated ErrorsUser Safety Cont-Batch Mode Chng Network Failed Mast Network Failed I/O Service and Maintanance Lubrication Procedure Seasonal Inspection and Service FAN Blade Removal and Installation FAN Removaland Installation FAN Motor Removal Heater Parts Removal and Installation Main Controls Meter Roll Servicing HOW to Clear a Jammed Metering Roll Trouble Analysis Procedure PNEG-951 PNEG-951 PNEG-951 PNEG-951 Special Setup Screens Meter Roll Reverse Meter Roll DisableAIR Switch Testing Select Unload Method Reverse time Model Number Select Dryer AddressAttempt to Refill FAN/HEATER Select Temperature Scale SET Time & Date Possible reasons for using On/Off burner Contrast Adjustment PNEG-951 Drying Charts Series Dryers Continuous Dry & Cool Staged Batch Continuous Full Heat Continuous Dry & Cool Staged Batch PNEG-951 Technical Reference Control Panel Jumper Wiring Control Panel Internal Wiring PNEG-951 PNEG-951 PNEG-951 PNEG-951 PNEG-951 PNEG-951 Lower Control BOX Back Panelwiring Network FAN/HEATER Interface FAN Computer Pinouts FAN Control BOX Upper Terminal Strip Upper Back Panel Control Wiring 100 PNEG-951 PNEG-951 101 GSI Group, Inc 1004 E. Illinois St Assumption, IL Phone Fax