Decal DC-973 | GSI Outdoors PNEG-951 guide

Decal: DC-973

Decal DC-973 is located on the rear plenum access door (inside and outside).

Decal: DC-388

Decal DC-388 is located on the hitch tongue.

Decal: DC-1249

Decal DC-1249 is located on the hitch tongue.

14

PNEG-951

Image 14

GSI Outdoors PNEG-951 manual Decal DC-973

Contents

3 Module Network Portable Dryer Models Page Table of Contents Drying Charts Module Network Dryer Manual Introduction Section GSI GROUP, INC. Warranty Safety First Dryer Operation Decal DC-889 Decal DC-972 Decal DC-1227 Decal DC-973 USE Caution in the Operation of this Equipment PNEG-951 Control Panel Switch Panel Layout Load Auger Switch Control Power SwitchDrying Mode Switch FAN Switch RUN Switch Moisture Control SwitchOutside Light Switch Stop Switch Setup Button Out of Grain Time Delay ButtonScreens Button Set Out of Grain View Grain Temps Meter Roll SP Avg User Hour Meter Cool Button Help ButtonDRY Button Unload Button Stats Button PNEG-951 Dryer Pre Season Checks RUN Button Electrical PowerInspect the Metering Rolls Fuel Check Unload TWO Speed Operation Load AugerUnload ONE Speed Operation Metering Roll Operation Burner Test Fire FAN SwitchesBurner Safety Meter Roll 2 Speed Display Dryer Shutdown Emergency Dryer Shutdown PNEG-951 Dryer Startup and Operation Fan and Auger Delays Initial Setup ParametersTimer and Delay Settings Dryer Shutdown Load Delay OUT of Grain TMR position Unload Delay Setting Up The Temperature Set Points Drying mode switch is in the Continuous position Startup Procedure Startup Continuous Flow Drying Mode Full Heat-Continuous Flow Operation Dry and Cool-Continuous Flow Operation Staged Batch Drying Mode Continuous-Batch Operation PNEG-951 Dry Timer Operating Display Screens Main Display Screen PNEG-951 Safety Circuit Shutdown Messages Fan x Loss of Airflow FAN and Heater Generated ErrorsAir Switch x Stuck Fan x No Airflow Grain x Overheat Housing x High LimitGrain Temp Short Ignition Failure Plenum Temp Open Illegal FlameMotor Overload Plenum Temp Short Air System Failure INPUT/OUTPUT Generated ErrorsVapor x High Limit Aux Load Overload Meter Rolls Failed Grain Discharge WarningLoad Motor Overload Out of Grain Cont-Batch Mode Chng Master Display Generated ErrorsUser Safety Unload Motor Overload Network Failed I/O Network Failed Mast Service and Maintanance Seasonal Inspection and Service Lubrication Procedure FAN Blade Removal and Installation FAN Removaland Installation Heater Parts Removal and Installation FAN Motor Removal Meter Roll Servicing Main Controls HOW to Clear a Jammed Metering Roll Trouble Analysis Procedure PNEG-951 PNEG-951 PNEG-951 PNEG-951 Special Setup Screens Meter Roll Reverse Meter Roll DisableAIR Switch Testing Reverse time Select Unload Method Model Number Select Dryer AddressAttempt to Refill Temperature Scale FAN/HEATER Select Possible reasons for using On/Off burner SET Time & Date Contrast Adjustment PNEG-951 Drying Charts Series Dryers Continuous Dry & Cool Staged Batch Continuous Full Heat Continuous Dry & Cool Staged Batch PNEG-951 Technical Reference Control Panel Jumper Wiring Control Panel Internal Wiring PNEG-951 PNEG-951 PNEG-951 PNEG-951 PNEG-951 PNEG-951 Lower Control BOX Back Panelwiring Network FAN/HEATER Interface FAN Computer Pinouts FAN Control BOX Upper Terminal Strip Upper Back Panel Control Wiring 100 PNEG-951 PNEG-951 101 GSI Group, Inc 1004 E. Illinois St Assumption, IL Phone Fax