Manuals / Haier / Household Appliance / Septic System

Haier 3150 SF, 3150 SB 3A Ball Check Valve Pumps, Sanitary Ball Check Valve Pumps, Model, 310622L

Models: 1590 SB 3150 SA 3150 SF 1590 SA 3150 SB

1 40

Download 40 pages 55.19 Kb

Page 36

Image 36

Model 3150

Dimensional Drawing

3A Ball Check Valve Pumps

22.0in

(558.8 mm)

28.4in.

(721.4 mm)

6.5 in.

(165.1 mm)

		23.5 in.
TI4929d		(596.9 mm)

37.6in.

(955.0 mm)

TI7610c

Sanitary Ball Check Valve Pumps		Flapper Check Valve Pumps

28.3 in.		37.5 in.	29.5 in.		38.1 in.
(718.8 mm)		37.5 in.	(749.3 mm)		(967.7 mm)
		(952.5 mm)
6.5 in.			5.9 in.
(165.1 mm)			(149.9 mm)
	19.3 in.			19.3 in.	TI4928d
	19.3 in.			(490.2 mm)
	(490.2 mm)	TI4685d
		TI4685d

36					310622L

Page 36

Image 36

Haier 3150 SF 3A Ball Check Valve Pumps, Sanitary Ball Check Valve Pumps, Flapper Check Valve Pumps, Model, 310622L

Contents

Model SA3AAA Shown Instructions/Parts ListHigh Sanitation Pumps 310622L Contents ContentsDimensional Drawing Technical Data Warnings WarningsFIRE AND EXPLOSION HAZARD PRESSURIZED EQUIPMENT HAZARD BURN HAZARD PERSONAL PROTECTIVE EQUIPMENT Installation InstallationGeneral Information Leak Detection System Ground Wire Connection MountingsAir Line Fluid Suction Line Typical Installation FIG. 3 Typical Floor-Mount InstallationFluid Outlet Line Changing the Orientation of the Fluid Inlet and Outlet Ports Air Exhaust VentilationFIG. 4 Orientation of Fluid Ports FIG. 5 Venting Exhaust Air E Master air valve for accessories F Air line filter P MufflerA Air supply line B Bleed-type master air valve required for pump C Air regulator D Air line quick disconnect Pressure Relief Procedure Starting and Adjusting the PumpOperation Sanitizing the Pump Before First Use Maintenance Routine Cleaning of Product Contact Section of PumpMaintenance Lubrication Preventive Maintenance Schedule Maintenance PersonOperator Task Maintenance Troubleshooting TroubleshootingPROBLEM Follow Pressure Relief Proce erly/cleanly due to imbalance Leak in inlet or outlet sanitary fitLoose sanitary clamp Tighten clamp Service Repairing the Air ValveService Disassembly Reassembly 8. Install the valve carriage 105 so its tabs slip into the grooves on the narrow end of the actuator pis- tons 111. See FIG 3A Ball Check Assembly Check Valve Repair Service For Sanitary Ball Check pumps remove ball gasket Sanitary Ball Check AssemblyFlapper Check Assembly TI8769a Diaphragm Repair Tools Required Sanitary Pump 3A Pumpdiaphragm plate side high strength thread lock shaft side Bearing and Air Gasket Removal Service Pump Matrix 3150 Stainless Steel Sanitary Pumps1590 Stainless Steel Sanitary Pumps Pump Matrix Sanitary Ball Check Valve Assembly Flapper Check Valve AssemblySanitary Diaphragm Assembly Parts Drawing Parts List Pump Configuration Parts ListInlet and Outlet Parts List Parts List Diaphragm Material Parts List Indicates replacement parts † Indicates a recommended spare partPart 3150 Check Ball Material Parts List Indicates replacement parts † Indicates a recommended spare part center housing bore Apply medium strength adhesive to outsideApply a medium strength thread locker to screw threads and torque to 130-150 in-lbs Leak Detector and Pump Stand Parts List Air Section PartsFluid Section Parts Accessories Accessories3150 Conversion Kits 15D990 Leak Detector Dimensional Drawing ModelModel TI8778a Technical Data Santoprene is a registered trademark of the Monsanto CoLoctite is a registered trademark of the Loctite Corporation Performance Chart 1590 3A Performance ChartTest Conditions Pump tested in water with inlet submerged To find Fluid Outlet Pressure 3A Ball Check Valve Pumps Sanitary Ball Check Valve PumpsFlapper Check Valve Pumps Technical Data 3150 3A Performance Chart Model Graco Standard Pump Warranty Extended Product WarrantyGraco Warranties Graco Information