Hearth and Home Technologies SL-550TRSI-AUE instruction

		FLUEING WITH THREE (3) 90° ELBOWS
		V (FT.)	H (FT.)		H + H1 (FT.)
		1´ MIN. (0.30M)	1´ MAX. (0.30M)		3´ MAX. (0.91M)
		2´ MIN. (0.61M)	2´ MAX. (0.61M)		5´ MAX. (1.52M)
		3´ MIN. (0.91M)	4´ MAX. (1.22M)		8´ MAX. (2.44M)
		4´ MIN. (1.22M)	6´ MAX. (1.83M)		12´ MAX. (3.66M)
			H = 6´ MAX. (1.83M)	H+H1	= 12´ MAX. (3.66M)
		NOTE: V + V, + H + H1 = 33’ (10.06M) MAX.
V1
			V
			H
		H1
		USE DVP-SERIES
		COMPONENTS ONLY.
H2
					V
			H1
FLUEING WITH THREE (3) 90° ELBOWS
V (FT.)	H (FT.)	H + H1 + H2 (FT.)
1´ MIN. (0.30M)	1´ MAX. (0.30M)	2´ MAX. (0.61M)
2´ MIN. (0.61M)	2´ MAX. (0.61M)	4´ MAX. (1.22M)
3´ MIN. (0.91M)	3´ MAX. (0.91M)	8´ MAX. (2.44M)
4´ MIN. (1.22M)	4´ MAX. (1.22M))	10´ MAX. (3.05M)			H
V+H+H1+H2 = 30´MAX.(9.14M)	H=4´MAX.(1.22M)	H+H1+H2 =10´MAX.(3.05M)
Figure 16.
16	Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. B • 7/06

Image 16

Hearth and Home Technologies SL-550TRSI-AUE manual Flueing with Three 3 90 Elbows

Contents

Model SL-550TRSI-AUE Kensington Boulevard, Lakeville, MN 55044 USA Heat & Glo Quality Systems registered by SGS ICS Table of Contents Diagram of SL-550TRSI-AUE Top Flue Installation InstructionsRear Flue Framing Dimensions Introduction Space heaters Model Flue Termination Approvals Flue System ApprovalsIdentifying Flue Components DVP90ST Heat & Glo SL-550TRSI-AUE 2079-902 Rev. B 7/06 Vertical Flueing Maximum 10.97MUSE SL D-SERIES USE DVP-SERIES Components only USE SL D-SERIES Components Only Flueing with ONE 1 90 Elbow USE DVP-SERIES Components + H FT. M Flueing with TWO 2 90 ElbowsFT. V M FT. HM Flueing with TWO 2 90 Elbows Flueing with Three 3 90 Elbows + H1 FT. M Flueing with Three 3 90 Elbows Installing Flue Components Nent and the Outer Heater Wrap Assembling Flue Components Install Support Brackets Continue Adding Flue Components Installing Support Brackets Hole and New Framing Members Flue Termination Connecting the GAS Supply Gas Supply Line Ignition System Wiring Shock Risk Blower FAN Finishing Ceiling Installing the Trim Installer TestingPilot Assembly 3 4 5 6 7 Heat & Glo SL-550TRSI-AUE 2079-902 Rev. B 7/06 Heat & Glo SL-550TRSI-AUE 2079-902 Rev. B 7/06 Trol Wiring System of this Unit Operating InstructionsOperating This Appliance MAY Exhibit a Slight Carbon Deposition Safety & Lighting Information Do not Connect 220/240 VAC to the Control Valve Glass Door When IT is HOT Servicing and MaintenanceFAN Operation Removal of Components for Service Parts ReplacementAdjustments and Replacement Parts Removal of Covers for Servicing Maintenance Tasks Doors Inspect Maintenance Tasks Troubleshooting Electronic Ignition System Pan beneath the burne Log set assembly SL-550TRSI-AUE SL-550TRSI-AUE Service Parts List Heat & Glo SL-550TRSI-AUE 2079-902 Rev. B 7/06 Melbourne