Manuals / Hearth and Home Technologies / Household Appliance / Electric Heater

Hearth and Home Technologies SL-550TRSI-AUE Use Sl D-Series Components Only, Ft. M, 1 MIN.0.30M

Models: SL-550TRSI-AUE

1 40

Download 40 pages 39.95 Kb

Page 12

Image 12

NOTE: A 146mm section of vertical pipe must be attached to the heater before a 900 elbow.

USE SL D-SERIES

COMPONENTS

ONLY.

	FLUEING WITH ONE (1) 90° ELBOW
	V		H
	FT. (M)		FT. (M)
	1' MIN.(0.30M)		2' MAX.(0.61M)
	2' MIN.(0.61M)		4' MAX.(1.22M)
	3' MIN.(0.91M)		8' MAX.(2.44M)
	4' MIN.(1.22M)		10' MAX.(3.05M)
Figure 11.	V + H = 30' (9.14M)
Figure 11.
FLUEING WITH ONE (1) 90o ELBOW
V (FT.)		H (FT.)
1' MIN. (0.30M)		3' MAX. (0.91M)
2' MIN. (0.61M)		6' MAX. (1.83M)
3' MIN. (0.91M)		9' MAX. (2.74M)
4' MIN. (1.22M)		12' MAX. (3.66M)
V+H =36' MAX. (10.97M)		H= 12' MAX. (3.66M)
			V
USE DVP-SERIES
COMPONENTS
	ONLY.
Figure 12.
12		Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. B • 7/06

Page 12

Image 12

Hearth and Home Technologies SL-550TRSI-AUE manual Use Sl D-Series Components Only, FLUEING WITH ONE 1 90 ELBOW, Ft. M

Contents

MODEL SL-550TRSI-AUE INSTALLATION AND OPERATION INSTRUCTIONSTHIS MANUAL MUST BE USED FOR INSTALLATION AND RETAINED BY HOMEOWNER FOR OPERATION AND MAINTENANCEMODEL SL-550TRSI-AUE TABLE OF CONTENTS Figure 1. Diagram of SL-550TRSI-AUE Heat & Glo SL-550TRSI-AUE 2079-902 Rev. B 7/061.0 INSTALLATION INSTRUCTIONS Top FlueRear Flue Minimum Clearances from the Fireplace to Combustible Materials1.1 INTRODUCTION Figure 3. Framing DimensionsFLUE FRAMINGHorizontally from an openable window, door, non-mechanical air Vertically below an openable window, non-mechanical airSpace heaters Below eaves, balconies or other projections1.2 FLUE SYSTEM APPROVALS MODELFLUE TERMINATION APPROVALS Identifying Flue ComponentsNOTE PIPES OVERLAP 32mm AT EACH JOINT Heat & Glo SL-550TRSI-AUE 2079-902 Rev. B 7/06NOTE PIPES OVERLAP 1 3/8 INCHES 35mm AT EACH JOINT Heat & Glo SL-550TRSI-AUE 2079-902 Rev. B 7/06Vertical Flue Restrictor VERTICAL FLUEING36 MAXIMUM 10.97M USE SL D-SERIESUSE SL D-SERIES COMPONENTS ONLY FLUEING WITH ONE 1 90 ELBOWFT. M FT. MFLUEING WITH TWO 2 90 ELBOWS H + HFT. M FT. MUSE DVP-SERIES COMPONENTS ONLYFLUEING WITH TWO 2 90 ELBOWS H + H1FLUEING WITH THREE 3 90 ELBOWS H + HFT. M FT. MUSE DVP-SERIES COMPONENTS ONLYFLUEING WITH THREE 3 90 ELBOWS V FTInstalling Flue Components Flueing Out the Rear FlueSYSTEM IS ATTACHED TO THE REAR STARTING COLLARS. SEE FIGURE Flueing Out the Top FlueInstalling Flue Components A. On the REAR of the heater1. Attaching the First Flue Component to the Start- ing Collars NENT AND THE OUTER HEATER WRAPInstall Support Brackets 3. Install Support BracketsPROCEED TO STEP Figure 21. Seams4. Install Firestops For Vertical RunsFigure 23. Installing Support Brackets Flue Pipe & FirestopC. Flue Termination Figure 26. Ceiling Firestop Ceiling SideFigure 27. Attic Firestop Figure 28. Venting through the Wall1.3 CONNECTING THE GAS SUPPLY Figure 29. Gas Supply Line1.4 IGNITION SYSTEM WIRING Shock Risk1.5 BLOWER FAN BLOWERVARIABLE SPEED CONTROL BLACK BLACK 240VAC JUNCTION BOX BLUE BROWN GREEN/YELLOW1.6 FINISHING 1.7 INSTALLER TESTING Installing the TrimPilot Assembly 1.8 LOG PLACEMENT INSTRUCTIONS Log Set Assembly LOGS-550TRSI-AUE 1 2 3 4 5 6 7TABS LOG #3 SRV349-704 Position log #3 so that its right edge sits on log #1 as shown and its left edge sits on the first grate bar behind log #2 LOG #6 SRV550-718 Place log #6 on the base on front of the grate as shown 2.0 OPERATING INSTRUCTIONS OPERATING CAUTIONSTROL WIRING SYSTEM OF THIS UNIT WARNING THIS UNIT IS NOT FOR USE WITH SOLID FUEL2.1 SAFETY & LIGHTING INFORMATION FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS TO TURN OFF GAS TOAPPLIANCE3.0 SERVICING AND MAINTENANCE 2.2 FAN OPERATIONGLASS DOOR WHEN IT IS HOT Pilot Assembly3.2 REMOVAL OF COMPONENTS FOR SERVICE 3.3 PARTS REPLACEMENT3.4 ADJUSTMENTS AND REPLACEMENT PARTS 3.1 REMOVAL OF COVERS FOR SERVICING3.5 MAINTENANCE TASKS Maintenance TasksDoors Inspect 3.6 TROUBLESHOOTING SymptomElectronic Ignition System Possible CausesSymptom Electronic Ignition System - continuedPossible Causes Corrective ActionsService Parts 22 Log set assemblyNG, LP Exploded Parts Diagram SL-550TRSI-AUESL-550TRSI-AUE Service Parts List AccesssoriesPage Melbourne PerthSydney For Service or Replacement Parts Contact

USE SL D-SERIES

FLUEING WITH ONE (1) 90° ELBOW

FT. (M)

1' MIN.(0.30M)

2' MAX.(0.61M)

2' MIN.(0.61M)

4' MAX.(1.22M)

3' MIN.(0.91M)

8' MAX.(2.44M)

4' MIN.(1.22M)

10' MAX.(3.05M)

V + H = 30' (9.14M)

USE DVP-SERIES

COMPONENTS