Manuals / Hearth and Home Technologies / Household Appliance / Electric Heater

Hearth and Home Technologies SL-550TRSI-AUE manual NOTE PIPES OVERLAP 32mm AT EACH JOINT

Models: SL-550TRSI-AUE

1 40

Page 9

		152mm	102mm
		152mm
	305mm
			DVP4
		DVP6
	DVP12
	362mm
310mm	51mm
MAX.	51mm
MAX.	MIN.
	MIN.
		610mm
	DVP12A		914mm
			1219mm
251mm		DVP24
	45.0O	DVP24
	45.0O
	260mm
	DVP45
		DVP36
		286mm
		184mm
		32mm TYP	DVP48
			DVP48
	217mm	13mm TYP
	319mm
	DVP90ST
	NOTE: PIPES OVERLAP 32mm AT EACH JOINT.

Figure 6. DVP-Series Balanced Flue Component Specifications (127mm inner pipe / 203mm outer pipe)

Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. B • 7/06

Page 9

Image 9

Hearth and Home Technologies SL-550TRSI-AUE manual NOTE PIPES OVERLAP 32mm AT EACH JOINT

Contents

INSTALLATION AND OPERATION INSTRUCTIONS MODEL SL-550TRSI-AUETHIS MANUAL MUST BE USED FOR INSTALLATION AND RETAINED BY HOMEOWNER FOR OPERATION AND MAINTENANCEMODEL SL-550TRSI-AUE TABLE OF CONTENTS Heat & Glo SL-550TRSI-AUE 2079-902 Rev. B 7/06 Figure 1. Diagram of SL-550TRSI-AUETop Flue 1.0 INSTALLATION INSTRUCTIONSRear Flue Minimum Clearances from the Fireplace to Combustible MaterialsFigure 3. Framing Dimensions 1.1 INTRODUCTIONFLUE FRAMINGVertically below an openable window, non-mechanical air Horizontally from an openable window, door, non-mechanical airSpace heaters Below eaves, balconies or other projectionsMODEL 1.2 FLUE SYSTEM APPROVALSFLUE TERMINATION APPROVALS Identifying Flue ComponentsHeat & Glo SL-550TRSI-AUE 2079-902 Rev. B 7/06 NOTE PIPES OVERLAP 32mm AT EACH JOINTHeat & Glo SL-550TRSI-AUE 2079-902 Rev. B 7/06 NOTE PIPES OVERLAP 1 3/8 INCHES 35mm AT EACH JOINTVERTICAL FLUEING Vertical Flue Restrictor36 MAXIMUM 10.97M USE SL D-SERIESFLUEING WITH ONE 1 90 ELBOW USE SL D-SERIES COMPONENTS ONLYFT. M FT. MH + H FLUEING WITH TWO 2 90 ELBOWSFT. M FT. MCOMPONENTS ONLY USE DVP-SERIESFLUEING WITH TWO 2 90 ELBOWS H + H1H + H FLUEING WITH THREE 3 90 ELBOWSFT. M FT. MCOMPONENTS ONLY USE DVP-SERIESFLUEING WITH THREE 3 90 ELBOWS V FTFlueing Out the Rear Flue Installing Flue ComponentsSYSTEM IS ATTACHED TO THE REAR STARTING COLLARS. SEE FIGURE Flueing Out the Top FlueA. On the REAR of the heater Installing Flue Components1. Attaching the First Flue Component to the Start- ing Collars NENT AND THE OUTER HEATER WRAP3. Install Support Brackets Install Support BracketsPROCEED TO STEP Figure 21. SeamsFor Vertical Runs 4. Install FirestopsFigure 23. Installing Support Brackets Flue Pipe & FirestopFigure 26. Ceiling Firestop Ceiling Side C. Flue TerminationFigure 27. Attic Firestop Figure 28. Venting through the WallFigure 29. Gas Supply Line 1.3 CONNECTING THE GAS SUPPLYShock Risk 1.4 IGNITION SYSTEM WIRINGBLOWER 1.5 BLOWER FANVARIABLE SPEED CONTROL BLACK BLACK 240VAC JUNCTION BOX BLUE BROWN GREEN/YELLOW1.6 FINISHING 1.7 INSTALLER TESTING Installing the TrimPilot Assembly 1.8 LOG PLACEMENT INSTRUCTIONS Log Set Assembly LOGS-550TRSI-AUE 1 2 3 4 5 6 7TABS LOG #3 SRV349-704 Position log #3 so that its right edge sits on log #1 as shown and its left edge sits on the first grate bar behind log #2 LOG #6 SRV550-718 Place log #6 on the base on front of the grate as shown OPERATING CAUTIONS 2.0 OPERATING INSTRUCTIONSTROL WIRING SYSTEM OF THIS UNIT WARNING THIS UNIT IS NOT FOR USE WITH SOLID FUELFOR YOUR SAFETY READ BEFORE LIGHTING 2.1 SAFETY & LIGHTING INFORMATIONLIGHTING INSTRUCTIONS TO TURN OFF GAS TOAPPLIANCE2.2 FAN OPERATION 3.0 SERVICING AND MAINTENANCEGLASS DOOR WHEN IT IS HOT Pilot Assembly3.3 PARTS REPLACEMENT 3.2 REMOVAL OF COMPONENTS FOR SERVICE3.4 ADJUSTMENTS AND REPLACEMENT PARTS 3.1 REMOVAL OF COVERS FOR SERVICING3.5 MAINTENANCE TASKS Maintenance TasksDoors Inspect Symptom 3.6 TROUBLESHOOTINGElectronic Ignition System Possible CausesElectronic Ignition System - continued SymptomPossible Causes Corrective Actions22 Log set assembly Service PartsNG, LP Exploded Parts Diagram SL-550TRSI-AUEAccesssories SL-550TRSI-AUE Service Parts ListPage Perth MelbourneSydney For Service or Replacement Parts Contact

NOTE: PIPES OVERLAP 32mm AT EACH JOINT.

Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. B • 7/06