Manuals / Hearth and Home Technologies / Household Appliance / Electric Heater

Hearth and Home Technologies manual MODEL SL-550TRSI-AUE

Models: SL-550TRSI-AUE

1 40

Download 40 pages 39.95 Kb

Page 2

MODEL SL-550TRSI-AUE

PLEASE READ THIS MANUAL BEFORE INSTALLING

AND USING THIS APPLIANCE.

MODEL SL-550TRSI-AUE

IS AUSTRALIAN GAS ASSOCIATION APPROVED FOR NATURAL GAS OR PROPANE AS A BALANCED FLUE HEATER.

Refer to the appliance data plates for gas consumptions and pressures.

Installation of this appliance should only be carried out by an authorized person in ac- cordance with the manufacturer's instruc- tions. Appliance is to be installed in full com- pliance with the National Gas Installation Standard AS5601, the manufacturer's in- structions, and any local authorities' require- ments for gas, electrical and building regu- lations.

This appliance and its components are tested and safe when installed in accor- dance with this Installation Manual. Report to your dealer any parts damaged in ship- ment, specifically check glass condition. The gas logs and flue system components are in separate packages. Read all instructions

before starting installation and follow these instructions carefully during installation to ensure maximum benefit and safety. Fail- ure to follow them will void your warranty and may present a fire hazard.

The Heat & Glo, a brand of Hearth & Home Technologies Inc. warranty will be voided by, and Heat & Glo, a brand of Hearth & Home Technologies Inc. disclaims any responsibil- ity for the following actions:

•Installation of any damaged heater or flue system component

•Modification of the heater or balanced flue system installation other than as instructed by Heat & Glo, a brand of Hearth & Home Technologies Inc.

•Improper positioning of the gas logs or the glass door

•Installation and/or use of any component part not manufactured or approved by Heat & Glo, brand of Hearth & Home Technologies Inc., not withstanding any independent testing laboratory or other party approval of such component part or accessory.

IMPORTANT: Read all instructions carefully before starting installation. Failure to follow these installation instructions may result in a possible fire hazard and will void the warranty. Save this Manual for future reference.

Heat & Glo, a brand of Hearth & Home Technologies, Inc. 20802 Kensington Blvd., Lakeville, MN 55044, USA Copyright 2006 • Printed in U.S.A.

Heat & Glo Quality Systems registered by SGS ICS

2	Heat & Glo • SL-550TRSI-AUE • 2079-902 Rev. B • 7/06

Image 2

Hearth and Home Technologies manual MODEL SL-550TRSI-AUE

Contents

THIS MANUAL MUST BE USED FOR INSTALLATION AND RETAINED MODEL SL-550TRSI-AUEINSTALLATION AND OPERATION INSTRUCTIONS BY HOMEOWNER FOR OPERATION AND MAINTENANCEMODEL SL-550TRSI-AUE TABLE OF CONTENTS Figure 1. Diagram of SL-550TRSI-AUE Heat & Glo SL-550TRSI-AUE 2079-902 Rev. B 7/06Rear Flue 1.0 INSTALLATION INSTRUCTIONSTop Flue Minimum Clearances from the Fireplace to Combustible MaterialsFLUE 1.1 INTRODUCTIONFigure 3. Framing Dimensions FRAMINGSpace heaters Horizontally from an openable window, door, non-mechanical airVertically below an openable window, non-mechanical air Below eaves, balconies or other projectionsFLUE TERMINATION APPROVALS 1.2 FLUE SYSTEM APPROVALSMODEL Identifying Flue ComponentsNOTE PIPES OVERLAP 32mm AT EACH JOINT Heat & Glo SL-550TRSI-AUE 2079-902 Rev. B 7/06NOTE PIPES OVERLAP 1 3/8 INCHES 35mm AT EACH JOINT Heat & Glo SL-550TRSI-AUE 2079-902 Rev. B 7/0636 MAXIMUM 10.97M Vertical Flue RestrictorVERTICAL FLUEING USE SL D-SERIESFT. M USE SL D-SERIES COMPONENTS ONLYFLUEING WITH ONE 1 90 ELBOW FT. MFT. M FLUEING WITH TWO 2 90 ELBOWSH + H FT. MFLUEING WITH TWO 2 90 ELBOWS USE DVP-SERIESCOMPONENTS ONLY H + H1FT. M FLUEING WITH THREE 3 90 ELBOWSH + H FT. MFLUEING WITH THREE 3 90 ELBOWS USE DVP-SERIESCOMPONENTS ONLY V FTSYSTEM IS ATTACHED TO THE REAR STARTING COLLARS. SEE FIGURE Installing Flue ComponentsFlueing Out the Rear Flue Flueing Out the Top Flue1. Attaching the First Flue Component to the Start- ing Collars Installing Flue ComponentsA. On the REAR of the heater NENT AND THE OUTER HEATER WRAPPROCEED TO STEP Install Support Brackets3. Install Support Brackets Figure 21. SeamsFigure 23. Installing Support Brackets 4. Install FirestopsFor Vertical Runs Flue Pipe & FirestopFigure 27. Attic Firestop C. Flue TerminationFigure 26. Ceiling Firestop Ceiling Side Figure 28. Venting through the Wall1.3 CONNECTING THE GAS SUPPLY Figure 29. Gas Supply Line1.4 IGNITION SYSTEM WIRING Shock RiskVARIABLE SPEED CONTROL BLACK BLACK 240VAC JUNCTION BOX 1.5 BLOWER FANBLOWER BLUE BROWN GREEN/YELLOW1.6 FINISHING Pilot Assembly 1.7 INSTALLER TESTINGInstalling the Trim TABS 1.8 LOG PLACEMENT INSTRUCTIONS Log Set Assembly LOGS-550TRSI-AUE1 2 3 4 5 6 7 LOG #3 SRV349-704 Position log #3 so that its right edge sits on log #1 as shown and its left edge sits on the first grate bar behind log #2 LOG #6 SRV550-718 Place log #6 on the base on front of the grate as shown TROL WIRING SYSTEM OF THIS UNIT 2.0 OPERATING INSTRUCTIONSOPERATING CAUTIONS WARNING THIS UNIT IS NOT FOR USE WITH SOLID FUELLIGHTING INSTRUCTIONS 2.1 SAFETY & LIGHTING INFORMATIONFOR YOUR SAFETY READ BEFORE LIGHTING TO TURN OFF GAS TOAPPLIANCEGLASS DOOR WHEN IT IS HOT 3.0 SERVICING AND MAINTENANCE2.2 FAN OPERATION Pilot Assembly3.4 ADJUSTMENTS AND REPLACEMENT PARTS 3.2 REMOVAL OF COMPONENTS FOR SERVICE3.3 PARTS REPLACEMENT 3.1 REMOVAL OF COVERS FOR SERVICINGDoors Inspect 3.5 MAINTENANCE TASKSMaintenance Tasks Electronic Ignition System 3.6 TROUBLESHOOTINGSymptom Possible CausesPossible Causes SymptomElectronic Ignition System - continued Corrective ActionsNG, LP Exploded Parts Diagram Service Parts22 Log set assembly SL-550TRSI-AUESL-550TRSI-AUE Service Parts List AccesssoriesPage Sydney MelbournePerth For Service or Replacement Parts Contact