Heat & Glo LifeStyle LUX60 Table of Contents, Safety Alert Key, User Guide, Installer Guide

Safety Alert Key:

•DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

•WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

•CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

•NOTICE: Used to address practices not related to personal injury.

Table of Contents

	A.	Congratulations	2
	B.	Limited Lifetime Warranty	5
	1 Listing and Code Approvals
	A.	Appliance Certification	7
	B.	Ceramic Glass Specifications	7
	C.	BTU Specifications	7
	D.	High Altitude Installations	7
	E.	Noncombustible Materials Specification	7
	F.	Combustible Materials Specification	7
	G.	Electrical Codes	7
	H.	Requirements for the Commonwealth
		of Massachusetts	8

User Guide

2 Operating Instructions

A.	Gas Fireplace Safety	9
B.	Your Fireplace	9
C.	Clear Space	10
D.	Decorative Doors and Fronts	10
E.	Fixed Glass Assembly	10
F.	Operation of the LUX60	10
G.	Remote Operation	10
H.	Before Lighting Fireplace	11

I.IntelliFire Ignition System (IPI) Lighting

	Instructions	12
J.	After Fireplace is Lit	13
K.	Frequently Asked Questions	13
3 Maintenance and Service
A.	Maintenance Tasks-Homeowner	14
B.	Maintenance Tasks-Qualified Service Technician	16

Installer Guide

4 Getting Started
A.	Typical Appliance System	20
B.	Design and Installation Considerations	21
C. Tools and Supplies Needed		21
D. Inspect Appliance and Components		21

5 Framing and Clearances
A.	Select Appliance Location	22
B.	Assemble Steel Stud Kit	22
C.	Construct the Appliance Chase	23
D.	Clearances	23

6	Termination Locations
	A. Vent Termination Minimum Clearances		25
7	Vent Information and Diagrams
	A.	Approved Pipe	27
	B.	Vent Table Key	27

C.	Use of Elbows	27
D.	Measuring Standards	27
E.	Vent Diagrams	28

8 Vent Clearances and Framing

A.	Pipe Clearances to Combustibles	31
B.	Wall Penetration Framing	31
C.	Install the Ceiling Firestop	32
D.	Install Attic Insulation Shield	33

9 Appliance Preparation

A. Secure and Level the Appliance 34

10 Install Vent Pipe

A.	Assemble Vent Sections	35
B.	Assemble Slip Sections	36
C.	Secure the Vent Sections	36
D.	Disassemble Vent Sections	37
E.	Install Metal Roof Flashing	37
F.	Assemble and Install Storm Collar	38
G.	Install Vertical Termination Cap	39
H.	Heat Shield Requirements for Horizontal
	Termination	39
I.	Install Horizontal Termination Cap	40

11 Shrouds

A.	HHT Shrouds	41
B.	Field Constructed Shrouds	41

12 Gas Information

A.	Gas Pressure	43
B.	Gas Connection	43
C.	High Altitude Installations	43
D.	Install Flame Solenoid	44
E.	Setting Flame Height/Manifold Pressure	44

13 Electrical Information

A.	Wiring Requirements	45
B.	Electrical Service and Repair	45
C. Junction Box Installation		46

14 Wall Finishing

A.	Standard 1/2 in. (13 mm) Sheetrock	47
B.	Additional Decorative Finishing up to 1 in.
	(25 mm) Thick	48
C. Additional Decorative Finishing over 1 in.
	(25 mm) Thick	48

15 Appliance Setup

A.	Remove Glass Assembly	49
B.	Clean the Appliance	49
C.	Air Shutter Access & Adjustment	49
D.	Install Glass Rock	51

16 Troubleshooting

A. IntelliFire (IPI) Ignition System 52

Heat & Glo • LUX60 • 4062-116 • Rev. G • 4/11 3